Home > Runco > Projector > Runco Vx 1000d Projector User Manual

Runco Vx 1000d Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Runco Vx 1000d Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							SHARPNESSadjusts the amount of high-frequency detail in the image. This can be adjusted to the
    preference of the user. Keep in mind that when SHARPNESS is decreased, fine details in the image will
    become soft; when it is increased, fine details will become sharper but will also make the picture appear
    noisy if adjusted too high.
    All the picture adjustments (contrast, brightness, color, tint and sharpness) must be saved man-
    ually to Custom 1 or Custom 2 under ISF presets menu. If not, all the picture adjustments will be
    whited out when ISF presets (ISF Night, ISF Day, Custom 1, Custom 2) are changed.
    Input Position
    Indicates selection has been made for the Input Position selection menu
    •Press ENTER to allow shifting the Image Position Left/Right with the LEFT
    and RIGHT arrows.
    •Press ENTER to allow shifting the Image Position Up/Down with the LEFT
    and RIGHT arrows.
    •Press ENTER to allow shifting the Image Position Width with the LEFT and 
    RIGHT arrows.
    •Press ENTER to allow shifting the Image Position Height with the LEFT and 
    RIGHT arrows.
    •Press ENTER to allow shifting the Image Position Overscan percentage with 
    the LEFT and RIGHT arrows.
    ISF Preset
    s
    Indicates selection has been made for the ISF Presets selection menu.
    •Press ENTER to select the ISF Night calibration settings.
    •Press ENTER to select the ISF Day calibration settings.
    •Press ENTER to select the Custom 1 calibration settings, or scroll RIGHT and 
    press ENTER to save settings you have made.
    •Press ENTER to select the Custom 2 calibration settings, or scroll RIGHT and 
    press ENTER to save settings you have made.
    •Press ENTER to force the Presets back to their Factory Default settings.
    Information
    Indicates selection has been made for the Information selection menu
    •Indicates the unit Serial Number on the front panel display.
    •Indicates the Hardware Version number on the front panel display.
    •Indicates the Firmware Version number on the front panel display.
    •Indicates the Firmware Version build date on the front panel display.
         Input Position
    Left/Right
    Up/Down
    Width
    Height
    Overscan
           ISF Presets
         ISF Night
         ISF Day
         Custom 1   Save
         Custom 2   Save
          
         Factory Default
    X
                   Information
    Serial Num
    Hardware        0
    Firmware         0000.0000
    Date                April  7  2004
    20 
    						
    							21
    Basic Troubleshooting Tips
    The following is a basic troubleshooting guide that can assist you in resolving typical problems may
    result in normal operation. If you have encountered problems that are not listed in this guide, please
    contact your Runco dealer for assistance.
    The Projector does not turn on
    after initial installation. The
    Power LED on the front of the
    Controller stays red after the
    power button is pressed.
    The Projector and Controller
    are both on, but there is no
    video image on-screen.
    The Projector is producing a
    split screen or an otherwise
    scrambled image.
    The image appears too bright,
    and there is a loss of definition
    in the brightest areas of the
    image.· The RJ-11 (ComLink) cable is
    not connected between the
    Controller and Projector, or is
    connected improperly.
    · The projector is not plugged in,
    or its AC outlet is not active.
    Look at its power LED and see if
    it is illuminated.
    · Incorrect phone cord
    · The Controller is on the wrong
    source.
    · The Controller is on the correct
    source, but the source itself is
    off.
    · A progressive scan DVD is
    plugged into Component input
    rather than the RGB/Component
    input.
    · Contrast is set too high.
    · The DVD player is set for a
    high-level output.
    · The video signal has not been
    terminated properly somewhere
    in the system.· Use a standard RJ-11
    phone-type cord. Ensure it is
    firmly plugged into both the
    Controller and the Projector.
    · Ensure there is good conti-
    nuity in the RJ-11 cable.
    · Verify that the AC outlet is
    active, or that the Projector is
    plugged in.
    · Press MENU on the
    Projectors remote, and look
    to see which source is active
    (the arrow will be pointing to
    the active source). Select the
    correct source as appropriate.
    · Turn on the source. It is rec-
    ommended that all sources be
    turned on first BEFORE the
    VX-1000d.
    · Only NTSC/PAL can be input
    to the Component input.
    Progressive scan must go into
    RGB/Component.
    · Turn down the CONTRAST
    level on the Controller. Mid-
    range is 0; 
    · Set the DVD player for a
    nominal output (no boost or
    gain).
    · Ensure all video signals are
    terminated in 75 Ohms.
    PROBLEM POSSIBLE CAUSE SOLUTION 
    						
    							The image appears too
    washed out, or the darkest
    areas of the image appear too
    bright.
    The colors of the image
    appear abnormal
    The Projector will not turn
    back on after it was powered-
    down, or the image disap-
    pears during operation.· Brightness is set too high.
    · The DVD player may be set
    for too high of a brightness
    level.
    · The Red, Green and/or Blue
    outputs of the Controller or
    inputs to the Projector are
    reversed.
    · The Pr and Pb inputs on the
    Component input on the
    Controller are reversed
    · The Projector will not turn on
    for two minutes after power-
    down to protect its bulb.
    · The bulb has failed· Turn down the BRIGHTNESS
    level on the Controller. If possi-
    ble, use a PLUGE pattern to set
    the brightness level properly.
    · Set the DVD player for a nomi-
    nal output (no boost or gain).
    · Check the cable connections
    on the back of the Controller or
    on the Projector.
    · Wait two minutes until the LED
    on the front of the Controller
    turns red.
    22 
    						
    							23
    RS-232 Communications
    Baud rate:19200 (fixed)
    Bits:8
    No Parity
    All protocol in ASCII format
    RS-232 input connector pin numbers:TxD= Pin# 2, RxD= Pin# 3, GnD= Pin# 5
    Command format (single command):command value (i.e. brightness 100).
    NO
    TE:A space (not an underscore) or comma may be used between the command and its value.
    Command string format:command,command value, command etc.
    (i.e. COMPOSITE,BRIGHTNESS 100,ANAMORPHIC,)
    NO
    TE:In between commands, a comma or space may be used
    NO
    TE:A carriage return must be used after each command or string.
    Other notes:
    •  For command strings, a maximum of 255 characters can be used in a single string.
    •  PARAMETER min/max refers to a functions minimum and maximum value range. Inputting values above or 
    below their range may cause unpredictable (but not fatal) results.
    General Information 
    						
    							24
    COMMAND PARAMETER(min/max)Value stored? DESCRIPTION
    POWER 0/1 NA Turns DHD On and Off
    ON NA NA Turns DHD Controller on
    OFF NA NA Turns DHD Controller off
    COMPOSITE NA YES Selects the Composite video 
    input 
    SVIDEO1 NA YES Selects the S-Video 1 input
    SVIDEO2 NA YES Selects the S-Video 2 input
    COMPONENT NA YES Selects the Component input
    HD1 NA YES Selects the RGB HD 1 input
    HD2 NA YES Selects the RGB HD 2 input
    DVI1 NA YES Selects the DVI 1 input 
    DVI2 NA YES Selects the DVI 2 input 
    HD1Pass NA YES Selects the HD 1 Pass Thru 
    input
    HD2Pass  NA YES Selects the HD 2 Pass Thru 
    input
    ANAMORPHIC NA YES Selects the anamorphic
    aspect ratio
    STANDARD NA YES Selects the standard (4:3)
    aspect ratio
    LETTERBOX NA YES Selects the letterbox aspect ratio
    VIRTUALWIDE  NA YES Selects the VirtualWide aspect 
    ratio
    RGBNN NA YES Outputs color space RGB
    w/negative, negative sync
    RGBPP NA YES Outputs color space RGB
    w/positive, positive sync
    RGBS NA YES Outputs color space RGB
    w/embedded sync on green
    YUV NA YES HD YUV output color space
    IHPOS -100/100 YES Sets a value for horizontal     
    position input
    IVPOS -100/100 YES Sets a value for vertical     
    position input
    IWIDTH -100/100 YES Sets the value for width input
    IHEIGHT -100/100 YES Sets the value for height input
    OVERSCAN 0/10 YES Sets the overscan value in %
    OHPOS -100/100 YES Sets the value for width output
    OVPOS -100/100 YES Sets the value for height output
    OWIDTH -100/100 YES Sets the value for width output
    OHEIGHT -100/100 YES Sets the value for height output
    RS-232 Commands 
    						
    							25
    COMMAND PARAMETER(min/max)Value stored? DESCRIPTION
    BRIGHTNESS -100/100 YES Sets a value for brightness
    CONTRAST -100/100 YES Sets a value for contrast
    COLOR -100/100 YES Sets a value for color
    TINT -100/100 YES Sets a value for tint
    SHARPNESS -6/6 YES Sets a value for sharpness
    NIGHT NA YES Selects the ISF Night setting
    DAY NA YES Selects the ISF Day setting
    CUSTOM1 NA YES Sets the value per client
    CUSTOM2 NA YES Sets the value per client
    TRIGGER 1/3 YES Sets the trigger
    BKGND -100/-100 YES Sets the background color for 
    letterbox
    IHPOS? NA NA Returns input horizontal position 
    value
    IHEIGHT? NA NA Returns input vertical height 
    value
    OHPOS? NA NA Returns output horizontal
    position value
    OHEIGHT? NA NA Returns output vertical height
    value
    COLOR? NA NA Returns color setting value
    ASPECT? NA NA Returns current aspect ratio
    INPUT? NA NA Returns active input
    OUTRES? NA NA Returns output resolution
    SERIALNUM? NA NA Returns serial number
    DATE? NA NA Returns the date of mfg
    IVPOS? NA NA Returns input vertical position 
    value
    OVERSCAN? NA NA Returns overscan percentage
    OVPOS? NA NA Returns output vertical position 
    value
    BRIGHTNESS? NA NA Returns brightness setting value
    TINT? NA NA Returns tint setting value
    PRESET? NA NA Returns preset ISF day or night
    POWER? NA NA Returns power status
    ASPECTIN? NA NA Returns the input source aspect
    SWVER? NA NA Returns software version number
    IWIDTH? NA NA Returns input horizontal width 
    value
    PHASE? NA NA Returns phase setting value
    OWIDTH? NA NA Returns output horizontal width 
    value
    CONTRAST? NA NA Returns contrast setting value
    SHARPNESS? NA NA Returns sharpness setting value
    BKGND? NA NA Returns background setting 
    value
    INRES? NA NA Returns input resolution
    ASPECTOUT? NA NA Returns output screen size
    HWVER? NA NA Returns hardware version
    number 
    						
    							26
    Specifications
    Projector Type:Digital Light Processing™ (DLP™), Single HD-2+ DMD™ Chip
    Native Resolution:1280 x 720 (Designed for 16:9 screens only)
    Aspect Ratios:Determined by supplied processor
    Video Standards:NTSC, PAL
    DTV Compatibility:480p, 720p, 1080i
    Scan Frequency:Horizontal: 15-81 kHz
    Vertical: 43-100 Hz
    Picture Size:Recommended Width: 72-96 in.
    (16:9 screen) Maximum Width: 200 in.
    Throw Distance:Minimum: Zoom 1.85 x screen width 
    (Factor x Screen Width) Maximum: Zoom 2.40 x screen width
    Horizontal / Vertical Offset:Horizontal: 0 / Vertical +/- 50%
    Light Output:CSMS S
    pecifications:
    Home Theater Calibration: 418-600 ANSI Lumens                   
    Foot-Lamberts: 15.6-22.4
    1500 ANSI Lumens                                                                                
    Contrast Ratio:CSMS Contrast Ratio: 211:1 to 229:1
    2700:1 to 3300:1
    Lamp:250W NSH
    Lamp Life:2000 hours @ 6500
    oKelvin
    Inputs:(1) RGB HV, (1) DVI w/HDCP, (1) RS-232                       
    12V Output:See Controller for specifications
    Power Requirements:100-240V AC, 50/60 Hz, 375W
    Operating Environment:40°- 95° F, (5°- 35° C), 0%-90% Humidity (non-condensing)
    Dimensions:Width: 20 7/8 in. (530 mm)
    (w/out feet) Depth: 21 5/8 in. (550.20 mm)
    Height: 7 1/8 in. (181 mm), with feet 8 1/4 in. (209.50 mm) 
    Weight: 50 lbs. (23 kg) (includes lens)
    Regulatory Approvals:Complies with FCC Class B, CE, C-Tick
    Limited Warranty: Projector: (2) Two year parts and labor from the date of delivery to the 
    end user.                  
    Lamp Warranty:1000 hours or (6) six months, which ever comes first.
    VX-1000d Projector: 
    						
    							27
    DHD Controller:
    Supplied Accessories
    Aspect Ratios:Anamorphic, Letterbox, VirtualWide™, 4:3 
    Input standards:NTSC / PAL
    Output resolution:720P
    Outputs:(1) HD - R (Pr), G (Y), B (Pb), H, V; (1) DVI w/HDCP
    Inputs:(1) Composite; (2) S-Video; (1) Component; (2) HD - R (Pr), G (Y), B 
    (Pb), H, V; (2) DVI w/HDCP
    Control Options:Discrete infrared remote, (2) RS-232, (1) 9-pin connector, (1) RJ-11, 
    Front panel controls
    Screen Trigger/
    Masking Outputs:(3) 12V DC, 1/8A
    Bandwidth:150 Mega Samples/Second (MSPS)
    Power Requirements: 100-240V AC (auto-sensing), 50/60 Hz, 160W
    Operating Environments:41°-95°F (5°-35°C); 0-90% Humidity (non-condensing)
    Dimensions:Width: 17 1/2 in. (444.50 mm) 
    Depth: 11 3/16 in. (284.10 mm) 
    Height: 3 3/4 in. (95.25 mm) 
    Weight: 13 lbs. (5.9 kg)
    Regulatory Approvals:Complies with FCC, CE, C-Tick
    Limited Warranty:(2) Two years parts and labor from the date of delivery to the end user.
    • Remote Control with 2 AAA batteries
    • Rack Mount hardware
    • (1) 6” RGBHV extension for the Controller, (1) 9-pin to RJ-45
    • Power cables (one for Projector, one for DHD Controller)
    • 50’ RJ-11 phone type cable
    • RS-232 to RJ-11 Adapter
    • Lens adjustment tool
    • User’s Manual
    • Warranty information 
    						
    							RUMA-010825
    rev 9-20-04 ver 2
    Runco International •2900 Faber Street •Union City, CA 94587 •ph (510) 324-7777 •fax (510) 324-9300 •www.runco.com 
    						
    All Runco manuals Comments (0)

    Related Manuals for Runco Vx 1000d Projector User Manual