Runco V50hd V63hd Dislay User Manual

							Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 37 
PREL
IMINARY
Height: Select Height from the Input Position menu to change the projected image 
height. Press  to increase the height; press   to decrease it.
Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture 
area of the video signal out beyond the edge of the display area. 
Some television programs are produced based on the assumption that older television 
sets may not display the outer edges of the broadcast picture area. Overscan effectively 
trims away these inactive, outer edges and enlarges the remaining portion of the image to 
fill the display area.
For HDTV, DVDs and other video sources, Overscan is generally not necessary or 
desirable.
This control defines the amount of overscan applied to the image. The range is from 
0 to 20. There are two overscan modes: 
Crop mode, each increment adds a mask at the top, bottom, left and right edges of 
the source image equal to 0.5% of the displayed horizontal resolution (1% total). A 
setting of 10, for example, crops the image 5% on all sides or 10% total.
Zoom mode, each increment adds a factor to the scaling of the source image so 
that the vertical and horizontal resolutions are 100% plus 1% increments of the size 
determined by the aspect ratio function. A setting of 10, for example, zooms in on the 
image 5% on all sides or 10% total.
Figure 4-6 illustrates the effect of each overscan mode setting. 
Figure 4-6. Overscan Modes
Off Crop Zoom
4:3
16:9
= Source Image Area
= Edge Noise
= Screen (16:9) 
						

							Operation
38 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Phase (RGB, Component or SCART sources): This control adjusts the phase of the 
pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB, 
Component or SCART image still shows shimmer or “noise” after Tracking has been 
optimized. 
For best results, use a good test pattern such as a smooth gray consisting of a clear 
pattern of black and white pixels, or a similar “half on, half off” graphic image. Adjust the 
slidebar until the image stabilizes and each pixel is clearly defined. You may notice that 
you can stabilize the image at more than one point. Use either setting in such cases. 
Tracking (RGB, Component or SCART sources): Tracking determines the frequency 
of the pixel sampling clock, indicated by the number of incoming pixels per line, so that all 
pixels generated by a particular source are sampled. 
Steady flickering or several soft vertical stripes or bands across the entire image indicates 
poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent 
across the screen, that aspect ratio is maintained and that pixel phase (see above) can be 
optimized. 
Memory PresetsFor each input, the DHD Controller lets you save image quality settings as presets that you 
can recall at a later time. You can create up to four presets per input and display mode 
(resolution and frame rate). 
The DHD Controller stores the following display modes in each memory preset:




 720p/24 Hz
 720p/25 Hz
 720p/30 Hz
 720p/50 Hz
 720p/60 Hz
 1080i/50 Hz
 1080i/50 Hz (Australia)
 1080i/60 Hz
 1080p/24 Hz
 1080p/25 Hz
 1080p/30 Hz
 1080p/50 Hz
 1080p/60 Hz
Use the Memory Presets menu to recall saved image presets, or to save image settings in 
the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated 
by a “Δ to its left; in the example shown here, ISF Night is selected.Adjust the Phase after adjusting Tracking (see below). 
Tip
Memory Presets
ÎISF Night
ISF Day
Custom 1 Save Reset
Custom 2 Save Reset
➤ 
						

							Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 39 
PREL
IMINARY
You should save changes to any of the following settings to a preset; otherwise they will 
be lost when a new input source or resolution is selected:
 Brightness

 Color saturation

 Sharpness

 Color temperature and white balance
To select a memory preset, press   or   to highlight it and press ENTER. 
To save the settings for the current input and display mode to the Custom 1 or Custom 2 
memory preset, select it, press  or  to highlight Save and press ENTER.
To reset the Custom 1 or Custom 2 memory preset to its factory-default state, select it, 
press  or  to highlight Reset and press ENTER.
Sleep Timer Select Sleep Timer from the Main Menu to turn off the V-50HD/V-63HD after a specified 
interval. Press   or   to select Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or 
4 Hours. Then, press ENTER. To save the settings for the current input and display mode to the 
ISF Night or ISF Day memory preset, select Save ISF Night or Save 
ISF Day from the Calibration menu (refer to Save ISF Night/Save 
ISF Day on page 44). 
Note
Sleep Timer
ÎOff
30 Minutes
60 Minutes
90 Minutes
2Hours
4Hours 
						

							Operation
40 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
InformationSignal / System: Select Information from the Main Menu, then choose either Signal or 
System to display information about the current input signal (resolution, frequency, type et 
cetera) and installed firmware versions, as well as other information that uniquely identifies 
your DHD Controller and display device. 
Should you ever need to contact Runco Technical Support, this information will help them 
answer your questions or resolve product performance issues.
Network: Select Information from the Main Menu, then choose Network to display 
information about the Ethernet network connection. 
To enable network communication via Ethernet, refer to IP Configuration on page 48.
Field Service / Manufacturing: The Field Service and Manufacturing menus are 
password-protected and intended for use only by Runco service personnel and factory 
technicians. 
Information
Signal
System
Network
Field Service
Manufacturing
➤
Signal
Input SourceHDMI 1
Signal Format1080p/60
Input Resolution1920x1080
Vertical Freq59.94 Hz
Horizontal Freq67.500 kHz
Pixel Clock148.500 MHz
Color SpaceREC709
Sync TypeSeparate
Memory PresetISF Night
System
ModelDHD-LS
Display NameV-50HD/V-63HD
Output Resolution1920x1080
Serial Number00000000
Boot Version4.0
Firmware Version4.0
Micro Version4.0
Network
MAC Address1A:2B:3C:4D:5E:6F
IP Address192.168.0.150
Subnet Mask255.255.0.0
Default Gateway192.168.1.1
DHCPEnabled
Network StatusConnected 
						

							Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 41 
PREL
IMINARY
Calibration Use the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the 
Memory Presets menu (see page 38) or use the corresponding remote control buttons. 
Display Color - Common Settings: Use the Display Color - Common Settings menu to 
adjust the color balance at the DHD Controller output. These settings are saved 
independently for each input and display mode.
Use the Gain controls to correct color imbalances in the bright areas of the 
image. A good way to do this is to use a test pattern consisting mostly of solid white 
areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr), 
green (Y) or blue (Pr), decrease the Gain for that color.
set: Use the Offset controls to correct color imbalances in the dark areas of the 
image. A good way to do this is to use a test pattern consisting mostly of dark gray 
areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr), 
green (Y) or blue (Pr), decrease the Offset for that color.
 Gamma: Select Gamma from the Display Color - Common Settings menu to choose a 
de-gamma curve. Used correctly, the Gamma control can improve contrast while 
maintaining good details for blacks and whites. If excess ambient light washes out the 
image and it becomes difficult or impossible to see details in dark areas, lower the 
gamma setting to compensate. This improves contrast while maintaining good details 
for blacks. Conversely, if the image is washed out and unnatural, with excessive detail 
in black areas, increase the setting. 
Mode: With the V-50HD/V-63HD, two Gamma adjustment modes are available: 
Simple or Advanced. The two modes are mutually exclusive; when you select the 
Simple mode, the Advanced selection in the Gamma menu is grayed out. Likewise, 
when you select Advanced, the Simple selection is grayed out.
Simple: Use the Simple Gamma control to perform gamma correction at the display 
according to a simple power law gamma function. The value chosen here 
corresponds to the power variable in this equation:
Output = Input
Power
The DHD Controller applies this gamma curve to all three primary color channels 
(red, green and blue). 
Advanced: To select a custom gamma curve, select Mode from the Gamma menu 
and set it to Advanced. Then, select Advanced from the Gamma menu to select one 
of up to 20 pre-programmed gamma tables. Custom gamma tables provide the 
ability to perform complex, non-linear gamma correction on each primary color 
channel independently of the others.
Calibration
ISF Settings
Display Color
Input Image
Input Color
Save ISF Night
Save ISF Day
Copy/Paste
Output Shift
Image Alignment
Splash Configure
OSD Position
You must enter a passcode to access the Calibration menu. Note 
						

							Operation
42 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
 Color Temp: Select Color Temp from the Display Color - Common Settings menu to 
adjust the color temperature. Color temperature establishes the “color of gray” by 
adjusting the 75% white point to various color points. 
What are “color points?”A “color point” is an x/y coordinate pair that defines a 
color’s location on the standard CIE chromaticity graph, shown in Figure 4-7. (CIE 
stands for “Commission Internationale de l’Éclairage” (International Commission on 
Illumination), the organization responsible for color measurement and management 
standards.)
Figure 4-7. CIE 1931 Chromaticity Diagram
Simple: Select Simple mode from the Color Temp menu to choose one of five color 
temperature presets: 3200K, 5500K, 6500K, 7500K and 9300K. The default setting, 
6500K, is appropriate for most situations. Higher settings produce a “bluer” picture; 
lower ones impart a reddish hue to the image. 
Table 4-2 lists the x- and y-coordinates for each color temperature preset in 
“Simple” mode. 
Table 4-2. Color Temperature Presets and Associated Color Points
Color Temperature PresetAssociated x/y Values
xy
3200K 0.423 0.404
5500K 0.332 0.348
0.00.10.20.30.40.50.60.70.80.91.0 0.0 0.1 0.2
0.3 0.4
0.5 0.6
0.7
0.8 0.9 1.0
x y
20002222 2500 2857 3333 4000 5000 5714 6667 8000 10000D50D65D93Red
BlueGreen
Cyan
Magenta
Yellow 
						

							Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 43 
PREL
IMINARY
Display Color - Panel Settings: These settings are also saved independently for each 
input and display mode.
 Panel Brightness: The Panel Brightness control changes the apparent brightness of 
the displayed image. Its effect is similar to that of a lamp intensity control on a projector. 
Use a higher setting for rooms with a lot of ambient light. Use a lower setting for more 
“theater-like” viewing conditions (little or no ambient light). 
 Power Mode: Select Power Mode from the Display Color - Panel Settings menu to set 
the power consumption threshold for the panel: High, Normal or Eco. The default 
setting is High. 
Input Image: The Input Image controls are functionally similar to those in the Picture 
menu (refer to page 32), but are accessible only by entering the Calibration menu 
passcode. 
Input Color: The Input Color controls are similar to those in the Display Color menu (see 
above), but adjust the color balance of the incoming signal. These settings are also saved 
independently for each input and display mode.
set (HD1, HD2 and Component/SCART inputs only): These controls 
operate similarly to those in the Display Color - Common Settings menu (described 
on page 41), but affect the Y, Pb and Pr signal components rather than the red, green 
and blue channels. 
use the Chroma Delay control to correct a mis-aligned image from a 
composite video source. Chroma delay in an image causes color shifts to occur to the 
left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If 
necessary, adjust this setting to eliminate them. 
se Filter: To apply noise filtering to the input signal, select Noise Filter from the 
Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i 
video sources. 
Use the left- or right-arrow buttons to select the desired amount of noise reduction, 
keeping in mind that higher settings (which reduce high frequencies) may also “soften” 
the image.
6500K 0.313 0.329
7500K 0.299 0.315
9300K 0.284 0.298
To prolong the life of the display, set the Panel Brightness only as 
high as is necessary to produce the desired brightness. 
The Input Image settings establish the “zero point” for the Picture 
menu settings, whose values represent offsets from the Input 
Image settings. For example, if you set Brightness to 10 in this 
menu, setting Brightness to 10 in the Picture menu results in an 
actual setting value of 20 (10+10).
Table 4-2. Color Temperature Presets and Associated Color Points
Color Temperature PresetAssociated x/y Values
xy
Tip
Note 
						

							Operation
44 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you 
should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to 
do this.
  Copy/Paste - Memory Preset: You can copy and paste settings from one memory 
preset to another. This gives you a convenient starting point for creating a new preset 
based on an existing one, to make the calibration process less time-consuming. 
For example, you can use the Copy/Paste Memory Preset feature to:
 Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
 Calibrate an input for 720p source signals, then use those settings for 1080i sources.
 Duplicate ISF Night settings for a given source and signal format and save them in the 
Custom 1 memory preset.
To use this feature, select Copy/Paste from the Calibration menu, then select Memory 
Preset. 
set - Copy Settings: Select Copy Settings from the Copy/Paste 
Memory Preset menu to place the settings for the current input source, signal format 
(resolution and frame rate) and memory preset onto a “clipboard,” which is a temporary 
memory location. When you do, the message “Settings Copied” briefly appears 
on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied 
settings. 
set - Paste Settings: To apply the settings on the clipboard to a 
different input source, signal format and/or memory preset, do any or all of the 
following:
 Switch to another input (for example, from HD1 to HD2).
 Change the output signal format at the source (for example, from 720p/60 to 
1080i/60).
 Switch to another Memory Preset (for example, from ISF Night to Custom 1).
Then, select Paste Settings from the Copy/Paste Memory Preset menu. If you want 
to keep these new settings, you must save them! (Refer to Save ISF Night/Save 
ISF Day on page 44 or Memory Presets on page 38.)
 Copy/Paste - Aspect Ratio: You can also copy and paste certain settings, such as 
those for Output Shift and Image Alignment (refer to page 45) from one aspect ratio or 
“screen” (refer to Screen on page 32) to another. 
To do this, select Copy/Paste from the Calibration menu, then select Aspect Ratio. 
spect Ratio - Copy Settings: Select Copy Settings from the Copy/Paste Aspect 
Ratio menu to place the Output Shift and Image Alignment settings for the current 
aspect ratio onto a “clipboard,” which is a temporary memory location. When you do, 
the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then 
re-appears, indicating the source of the copied settings. 
Copy/Paste
Memory Preset
Aspect Ratio
Memory Preset
Copy Settings
Paste Settings
Copied From:
Input Source HDMI 1
Signal Format 1080p/60
Memory Preset ISF Night
Copied settings are not retained after a power cycle. Note
Copy/Paste
Memory Preset
Aspect Ratio
Aspect Ratio
Copy Settings
Paste Settings
Copied From:
Aspect Ratio 16:9
Screen Screen 1
Copied settings are not retained after a power cycle. Note 
						

							Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 45 
PREL
IMINARY
spect Ratio - Paste Settings: To apply the Output Shift and Image Alignment 
settings on the clipboard to a different aspect ratio and/or screen, do either of the 
following:
 Switch to another aspect ratio (for example, from 16:9 to Cinema).
 Switch from Screen 1 to Screen 2 or vice versa.
Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings 
are saved automatically.
Output Shift: The controls in the Output Shift menu are similar to those in the Input 
Position menu, except that they change the characteristics of the output signal. These 
settings are saved independently for each aspect ratio. 
Image Alignment: The Image Alignment menu provides precise, nine-point control over 
the displayed image geometry. Use these controls as (and only if) needed to re-position 
the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) 
or “pincushion” distortion (mid-points not aligned with corners). See Figure 4-8. 
Figure 4-8. Keystone and Pincushion Distortion
Vertical Keystoning Horizontal Keystoning
Pincushion Distortion 
						

							Operation
46 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
To correct keystoning or pincushion distortion:
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Calibration from the Main Menu and enter the Calibration Menu passcode. 
3. Select Image Alignment from the Calibration Menu.
4. Select Corner Alignment to correct a “keystoned” image by adjusting the image 
corner positions. Select Midpoint Alignment to correct pincushion distortion by 
adjusting the image edge mid-points. See Figure 4-9. 
Figure 4-9. Image Alignment Controls
Splash Configure: Use the Splash Configure menu to control the appearance and 
behavior of the “splash” screen that appears on the display upon power-up. 
SF Calibrated/ISF Other: You can have the V-50HD/V-63HD display 
the owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up 
to 30 characters in length. 
Use the up or down cursor button to select a character. Use the right and left cursor 
buttons to change the cursor position. Press MENU when you have finished entering 
text. Use the built-in test pattern when adjusting the image corners or 
midpoints. To access it, check the Test Pattern box in the Corner 
Alignment or Midpoint Alignment menu. 
The “Left Middle y” setting also controls the “Right Middle” 
y-coordinate. Similarly, the “Top Middle x” setting also controls the 
“Bottom Middle” x-coordinate.
Tip
Top Left (x, y)
Left
Middle
(x, y)Right
Middl
e(x)
Bottom Left (x, y)Top Right (x, y)
Bottom Right (x, y) Top Middle (x, y)
Bottom Middle (y)
Notes:
1. Bottom Middle x = Top Middle x
2. Right Middle y = Left Middle y
3. Smaller “x” values move a point to the left; larger values move it to the right.
4. Smaller “y” values move a point up; larger values move it down.
Center
(x, y)
Note