Runco Dr 300c Projector User Manual

9
Projector Description
Input Panel
Top View
Input Panel
RGB / Component / HDS-Video
Video
Power Inlet
ComLink
Status
Power
Lens
Lens adjustments
• Outer ring focuses the lens
• Inner ring zooms the image
Status LED:indicates status of
Projector, including any faults.
See page 26 for fault indications.
IR Receiver:Receives infrared
commands from the Projector’s
remote (not used in the DR-300c
system).
Power Indication:
Green= Operation
Blinking= Warming up/cooling
down
Orange= Standby
Bottom view of...

10
Projector Placement and Offset Information
Ceiling Mount Configuration
Screen Center
Screen Top
Projector Base
angleC
B
A
Full Screen LengthHalf Screen
Length
6.090
2.842
1.745
Base plate to center of lens 1.895
3.398
Screen Center
Screen Top
Projector Base
angleC
B
A
Full Screen Length
Half Screen
Length
1.745
Base plate to center of lens 3.398
4.028
 Minimum: = (screen width x 2.0) =  __________ inches
 Maximum: = (screen width x 2.3) =  __________ inches
Distance between lens center and top edge of...

11
PFP Controller Description
Front Panel
menu
ratio
ratio
input
enter>
<
<
<
PIXEL FOR PIXELTM
1     2     3
4         5    6      7         8               9         10
1. IR RECEIVER
Receives the infrared signal from the remote control.
2.POWER BUTTON
Turns the unit ON or OFF. The Main Power switch on the rear of the unit must be on first for this button to be active.
3. POWER INDICATOR
When the PFP Controller is ON, this LED will illuminate GREEN. When the unit is OFF or in STANDBY, this LED will...

Rear Panel
12V TRIGGER
12V FUSERGB OUTPUT VIDEO INPUTS
RS-232 IN
MADE IN USA
AC 120V 60Hz, 15W
MASK
SCREENRGB/COMPONENT COMPOSITE V
HB G R Y Pr PbS-VIDEO
MADE IN USARUNCO INTERNATIONAL
HAYWARD, CA
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER. NO USER- 
SERVICEABLE PARTS INSIDE. REFER SERVICING 
TO QUALIFIED SERVICE CENTER.AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIRCAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN!
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS...

13
Remote Control Description
A. IR OUTPUT INDICATOR
Illuminates when a button is pressed, indicating that an IR signal is being
transmitted.
B. POWER BUTTON
Toggles the power on and off. For a discrete on or off command, you can
use the direct access buttons (see J). Note:When the main AC power
switch is first turned ON, the PFP Controller will go through an initiation
cycle for approximately 15 seconds. The PFP Controller cannot be turned
on or operated until the initialization is complete. 
C. UP...

14
Quick Set-up Guide
Connection Examples
12V TRIGGER
12V FUSERGB OUTPUT VIDEO INPUTS
RS-232 IN
MADE IN USA
AC 120V 60Hz, 15W
MASK
SCREENRGB/COMPONENT COMPOSITE V
HBG R YPrPbS-VIDEO
MADE IN USARUNCO INTERNATIONAL
HAYWARD, CA
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER. NO USER- 
SERVICEABLE PARTS INSIDE. REFER SERVICING 
TO QUALIFIED SERVICE CENTER.AV I S : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIRCAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN!
WARNING: TO REDUCE THE RISK OF FIRE
OR...

15
Overall Functional Description
The DR-300c systemconsists of the PFP Controllerand the DR-300c Projector. This sys-
tem is unique in the way it is controlled; the control center for this system is located within the
PFP Controller. The PFP Controller tells the Projector to turn on or off, controls its brightness,
contrast, color temperature and more. All of this is accomplished by Runcos unique ComLink,
which is the transfer of information between the PFP Controller and the Projector via their
ComLink...

4:3 Screen
16:9 Screen
Anamorphic Lens
16:9 Position
Keystone
Picture Orientation
Lamp Hours 20
16
Menu Description and Navigation
Input Select:
Composite
S-Video
>Component
High Definition:
RGB/Component
Aspect Ratio Select
Installer Adjust
Menu Tree
Anamorphic
Standard 4:3
Letterbox
Tint
Color
Brightness
Contrast
Sharpness
Luma Enhance*
Chroma Enhance*
Color Temperature*
Color Balance*
The menu tree above is an overall glance at the menu system in the DR-300c. This menu is
shown with the installation...

Source Selectionis done by highlighting the desired source with the up or down arrows
and pressing ENTER. Sources may also be selected by pressing the left or right arrows on
the front panel or remote, or by one of the direct access buttons on the remote (pg. 13).
Picture adjustments such as color, tint, brightness, etc, are unique per source.
Aspect R
atioselection is done by highlighting Aspect Ratio on the main menu and press-
ing enter. The Aspect Ratio menu will then appear; and either ANAMORPHIC,...

18
Picture Quality Adjustments
Main Menu
>COMPOSITE
S-VIDEO
COMPONENT
RGB/COMPONENT
ASPECT RATIO SELECT
INSTALLER ADJUSTTINT
COLOR
BRIGHTNESS
CONTRAST
SHARPNESS
LUMA ENHANCE*
CHROMA ENHANCE*
COLOR TEMPERATURE*
COLOR BALANCE*
Picture quality adjustments (also known as Front Panel Controls) are the controls that change differ-
ent parameters of the image such as the amount of color, black level, etc. While these adjustments
can be set to suit the needs of the user, there is a way to set these properly....