Runco Dlc 2000hd Projector User Manual

							Rear Panel
8
12V TRIGGER
12V FUSERGB VIDEO OUTPUT VIDEO INPUTS
RS-232 IN
MADE IN USA
AC 120V 60Hz, 15W
MASK
SCREENHDTV/COMPUTER COMPOSITE V
HB G R Y Pr PbS-VIDEO
MADE IN USARUNCO INTERNATIONAL
HAYWARD, CA
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER. NO USER- 
SERVICEABLE PARTS INSIDE. REFER SERVICING 
TO QUALIFIED SERVICE CENTER.AV I S : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIRCAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN!
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
6789104 23 1
5
11 1 2
13
COMLINK OUT
1. 12v FUSE
This fuse protects the 12v outputs from the MASK and SCREEN jacks.
(Screen Fuse: 5mm x  25mm, AGC, 0.5A, 250V, Fast Blow)
2. MASK
This is a 12V output that is used to trigger masking on screens that have that capability.
(For use on motorized screens only, 1/4A maximum load).
3. SCREEN
This is a 12V output that is used to trigger the screen to drop. 
(For use on motorized screens only, 1/4A maximum load).
4. RS-232 IN
This is for systems using serial (RS-232) to control the PFPController.
5. COMLINK OUT
The output of this jack must be connected to the ComLink input of the DLC-2000HD Projector.
If this is not connected, neither the Controller or the Projector can operate.
6. RGB OUTPUT
This is the RGB Video output of the PFP Controller. Connect the RGB output of the Controller via a
five-wire
RGB cable to the DLC-2000HD Projector.
7. HDTV/COMPUTER
This is the input for RGB or Component HDTV sources. Computer and Progressive DVD sources may also be
input here.
8. COMPONENT INPUT
This is the input for Component Videofrom sources such as DVD players.
Note: The component output from a DTV decoder or a progressive-scan DVD cannot be used with this port;
it must be used with the HDTV port.
9. S-VIDEO INPUT
This is the input for S-Videofrom sources such as Satellite receivers, S-VHS VCR’s and DVD players.
10. COMPOSITE VIDEO INPUT
This is the input for Composite Videofrom sources such as laser disc players, VCRs and other misc. sources.
11. POWER INPUT
Plug in Main Power here.
12. 115 VAC FUSE
This is the main AC Input fuse (.5A/250V).
13. MAIN POWER SWITCH
Disconnects or applies main power to the Controller. 
						

							9
Remote Control Description
A.IR OUTPUT INDICATOR
Illuminates when a button is pressed, indicating that an IR signal is being
transmitted.
B.POWER BUTTON
Toggles the power on and off. For a discreet on or off command, you can
use the direct access buttons (see J). Note:When the main AC power
switch is first turned ON, the Controller will go through an initiation cycle
for approximately 15 seconds. The Controller cannot be turned on or
operated until the initialization is complete. 
C. UPBUTTON
When no menus are present on-screen, the UP button will toggle you
through aspect ratios in the following order:
Standard (4:3)         Letterbox          Anamorphic
When the menu is on-screen, the UP button will move the cursor up within
the menu.  When an adjustment item has been selected (i.e. brightness),
the UP button will increase the value of that function.
D. LEFT BUTTON
When no menus are present on-screen, the LEFT button will toggle you
through the five different sources in the following order:
RGB HD Component HD           Component            S-Video         Composite
E. DOWN BUTTON
When no menus are present on-screen, the DOWN button will toggle you
through aspect ratios in the following order:
Anamorphic          Letterbox          Standard (4:3)
When the menu is on-screen, the DOWN button will move the cursor
down  within the menu. When an adjustment item has been selected (i.e.
brightness), the DOWN button will decrease the value of that function.
F. RIGHT BUTTON
When no menus are present on-screen, the RIGHT button will toggle you
through the five different sources in the following order:
Composite           S-Video           Component           Component HD          RGB HD
G.MENU BUTTON
Pressing the MENU button will bring up the main menu. If no action is
taken within approximately 10 seconds, the menu will time-out (disappear).
Also, if you are in an adjustment mode or function, pressing MENU will
bring the menu back one level.
H.ENTER BUTTON
When an item is highlighted on a menu, pressing ENTER will select that
item.
I.PROGRAMBUTTON
If the remote control loses its memory as a result of weak or dead batter-
ies, it must be re-programmed for the PFP Controllerscode set. 
To reprogram the remote, press the PROGRAM button followed by 0,1,3.
Note:Pressing Enter after typing in the code is not necessary.
J.DIRECTACCESSBUTTONS
These buttons will allow you to directly
access an aspect ratio, source, or turn the
unit on or off without having to go through
any menus.  These buttons are:
1: Selects COMPOSITE video
2: Selects S-video
3: Selects COMPONENT video
4: Selects Component HD
5: Selects RGB HD
6: Not used
7: Selects the ANAMORPHIC aspect ratio
8: Selects the STANDARD (4:3) aspect ratio
9: Selects the LETTERBOX aspect ratio
0: Turns the Controller ON.
OFF: Also known as the button left of 0,
this turns the Controller OFF.
M
RUNCO
PWR
A
B
C
D
E
J F G
H
I
12 3
45 6
78
9
INPUT
0
NPUT
I
OFF
ON 
						

							10
Menu Description and Navigation
INPUT SELECT
Standard Video:
Composite 
S-Video
Component
High Definition:
Component
RGB
ASPECT RATIO SELECT
Menu Tree
Anamorphic
Standard 4:3
Letterbox
Through the Main Menu, you can easily switch sources and Aspect Ratios.
To select a source, you may either use the direct access buttons on the remote (pg. 9) or the
Left/Right buttons on the remote or Front Panel (pgs. 7, 10). If you wish to select a source via the Main
Menu, press MENU, highlight the desired source with the Up/Down arrows and press Enter. The arrow
to the left of the sources indicates the source currently in use.
To select an Aspect Ratio, you may use either the direct access buttons on the remote (pg. 9) or
the Up/Down buttons on the remote or Front Panel (pgs. 7, 10). If you wish to select an Aspect Ratio
via the Main Menu, press MENU, highlight ASPECT RATIO and press Enter. The Aspect Ratio selection
menu will then appear; highlight the desired Aspect Ratio with the Up/Down buttons and press Enter.
If you are in the Main Menu and you highlight the currently selected source and press Enter, you will see
the image quality adjustment menu. You can access these functions (Contrast, Brightness, Color, Tint)
by highlighting one and pressing Enter. For best results, it is recommended that these adjustments be
left the way the installer set them during initial installation. These adjustments are detailed in the DLC-
2000HD installer menu.
Main Menu
> 
						

							Specifications
Projector Type:  LCD
Native Resolution:1366 x 768
Lamp: 250W Metal Halide
Inputs: RGB/Component
Bandwidth:  180 Mhz (RGB)
Power Requirements:  100-120 VAC, 200-240 VAC 50/60 Hz (export version)
Current: 3.3A (100-120 VAC), 1.7A (200-240 VAC)
Power Consumption:  360W
Dimensions:    Width: 16.310 in. (414 mm)
Depth: 25.801 in. (655 mm)
Height: 8.439 in. (214 mm)
Weight:   56 lbs. (25.4 kg)
Safety Regulations:  Complies with FCC Class B, CE, C-Tick
DLC-2000HD Projector:
11 
						

							12
Controller:
Supplied Accessories
• Remote Control w/ 2 AAA Batteries
• Rack Mount Hardware
• Power Cords (2)
• 50’ RJ-11 cable
• User’s Manual
• Warranty information
• DB9 to RJ-11 Connector
• DB9 Female to DB9 Male Connector Inputs:  (1) Component, (1) S-Video, (1) Composite, (1) HDTV/Computer
Input standards:NTSC/PAL/480p/720p/1080i/SVGA/XGA
Output format: 1366 x 768
Bandwidth:  Video inputs: 5.5 Mhz, HDTV/Computer: 100 Mhz
Power Input:  120V (220V export model), 50/60 Hz
Power Consumption:  15W
Control Options:  RS-232, Infrared, Front Panel
Operating Environment:  41°-95°F (5°-35° C),  0-90% humidity, Non-condensing
Dimensions:    Width: 17.45 in. (443.23 mm)
Depth: 16 in. (406.40 mm)
Height: 3.5 in. (88.90 mm)
Weight:   16 lbs. (7.26 kg)
Safety Regulations:  Complies with FCC Class B, CE, C-tick
Fuses: (Screen Fuse: 5mm x 25mm, AGC, 1A, 250V, Fast Blow)
(Main Fuse: 5mm x 20mm, 500mA, 250V, Slow Blow)
Rack Ears: Included 
						

							RUMA-006700 rev 11-03
Runco International .2900 Faber Street .Union City, CA 94587 .ph (510) 324-7777 .fax (510) 324-9300 .www.runco.com