Runco Cl 710lt Projector User Manual

							4. Basic Operation Runco CL-710/ CL-710LT User’s Manual18
4. Basic Operation
Turning on the Power      
Zoom/ Focusing    
Selecting Video Memory
■The Power LED lights orange when power is applied 
and the power switch is turned on.
■Press and hold the ON key on the remote control 
for ONE second to turn on the unit. The POWER 
LED will blink orange during warm up period, then 
light solid green. 
■ Searching…. will be displayed on the screen before 
the projector identifies the input signal. This message 
will remain on the screen until a valid signal is 
detected. 
■If an incompatible input signal exceeds the range of 
the projector a Not supportive timing message will 
be displayed on the screen. This message will remain 
on the screen until you change the input signal.
■Adjust the projection image size you need with the 
zoom ring on the lens. To focus the image, rotate the 
focus ring on the lens.
■Press M1, M2, M3 buttons to recall settings in the 
memory. 
■Press Default to select the default setting.
Focus
Zoom outZoom in 
						

							4. Basic Operation Runco CL-710/ CL-710LT User’s Manual19
Selecting ASPECT RATIO 
Direct Picture Adjust (Menu Bypass) 
Setting Menu  
■Select the proper aspect ratio according to the 
format of signal content. There are four aspect ratios 
for choice.
■Anamorphic: 4:3 image is stretched horizontally to 
fit the 16: 9 screen. This is for 16:9 DVDs.
■4 X 3: The input signal will be scaled to fit 4 : 3 
display mode in the center screen.
■LPos+, LPos-: Adjust Letterbox image vertical 
position.
■Letterbox: Image in letterbox format is enlarged to 
fit 16:9 full screen display and the upper/lower 
portion are compressed.
■VirtualWide: This transforms a 4x3 image to a 
16x9 image. 
■Press Color to adjust color intensity.
■Press Brightness to adjust picture brightness.
■Press Contrast to adjust picture contrast.
■Press Tint to adjust color tones.
■Press the Menu button to turn on /off the on-screen 
menu.
■Use the ARROW buttons (c,e,d,f) to select the 
menu or to make various adjustments.
■Press the Enter or f button to enter the setting of 
items in the menu, or press the Exit button to leave 
and save the setting of items in the menu.
■For more detailed settings, see Chapter 5 Menu on 
page 22.
■Press Picture to access the picture setting menu.
■Press Info to access projector information. 
						

							4. Basic Operation Runco CL-710/ CL-710LT User’s Manual20
Selecting Input Source   
PIP/ PBP function     
■When this unit is turned on, it will search for the 
input source you selected last time.
■You may select the input source directly on the 
remote control.
■Press the PIP button to enable the PIP function
■For PIP purposes, there are two groups of inputs 
separated by their display modes: 
Video Group: Video, S-Video and Component Y/C
B/
C
R inputs 
Graphic Group: HDTV input and Computer input. 
■The PIP can show one input from the Graphic Group 
within one input from the Video Group, or show one 
input from Video Group within one input from the 
Graphic Group.
■Press the PIP button to switch to the main window 
or turn off PIP function.
■Select the input source of main window by pressing 
the INPUT button.
■Press the ACTIVE button to switch to the active 
window. You can change the input signal setting in 
active window.
■Press PIP+ or PIP- to adjust the size of PIP window.
■Adjust the position of the PIP window with the 
ARROW keys (c,e,d,f).
■Press PBP to enable the PBP function. 
						

							4. Basic Operation Runco CL-710/ CL-710LT User’s Manual21
Turning off the Power 
■Press the OFF key on the remote control to turn 
off the unit.
■The POWER LED will blink green and the fans will 
speed up for a quick cool down. The projector 
will not respond to any command for 90 seconds. 
■The POWER LED will light solid orange once the 
cooling down cycle has completed.
■After turning off the unit, the POWER LED will 
blink green and the fans will operate at high speed 
for 90 seconds.
■Fans will run for three minutes to cool.
■You may turn the projector back on after the first 
90 seconds. 
						

							5. Menu Runco CL-710/ CL-710LT User’s Manual22
5. Menu
Using the Menu 
This unit is equipped with an on-screen display (OSD) menu for making various adjustments and settings. 
There are four different menu languages; see page 24 Language setting for more details.
■Press the Menu button to turn on /off the on-screen display menu.
■Use the ARROW buttons (c,e,d,f) to select the menu or to make various adjustments.
■Press the Enter or f button to enter the setting of items in the menu, or press the Exit button to leave and save 
the setting of items in the menu.
Main Menu
When the Menu button is pressed on the remote control, the main menu will appear on-screen. An example of the 
main menu is shown above. Use c or d button to move the item you want to choose and then press the Enter or f 
button.
The active source is indicated by an arrow ( 
> ) to the left of the source; note that in the example above, Video is the 
current source.
Runco CL-710
  > Video
     S-Video
     Component
     Component HD
     RGB HD
     DVI-I
     -----------------------
     Aspect Ratio
     Options
     Setup
Source selection and picture quality adjustments
Aspect ratio selection
Option selection
Setup selection 
						

							5. Menu Runco CL-710/ CL-710LT User’s Manual23
Picture Quality Adjustments
To access the picture quality adjustments, press Menu, highlight the active source (indicated by the arrow) and press 
Enter or f. The picture quality sub-menu will then appear (see above).
To make an adjustment to a particular function, highlight the function with the c or d arrow button and press Enter 
or fto activate a scroll bar for that adjustment.
To enter into the memory selection menus, use Store and Recall menus to save and load three different memories. 
There are three memories: Memory 1, Memory 2 and Memory 3.
Aspect Ratio
There are four aspect ratios available that can be selected for video signal inputs.
16:9 Screens:
■ANAMORPHIC: The image is compressed vertically, but anamorphic software will appear properly 
proportioned. This is best suited for use with 16:9 DVDs.  
Runco CL-710
  > Video
     S-Video
     Component
     Component HD
     RGB HD
     DVI-I
     -----------------------
     Aspect Ratio
     Options
     Set UpAdjustment
     Brightness
     Contrast
     Color
     Tint
     Sharpness
     Filter
     Temperature
     Store
     Recall 
Runco CL-710
  > Video
     S-Video
     Component
     Component HD
     RGB HD
     DVI-I
     -----------------------
     Aspect Ratio
     Options
     Set Up
Adjustment
     > Anamorphic (16:9)
        Standard (4:3)
        Letterbox
        Virtual Wide
Active Image Area 
						

							5. Menu Runco CL-710/ CL-710LT User’s Manual24
■4 x 3:  The input signal will be scaled to fit in the center of the 16:9 screen.  
■LETTERBOX: The image in the Letterbox mode will be stretched vertically, and the top and bottom portion 
blanked off. This ratio is best suited for LaserDisc movies or non-anamorphic DVDs.
■VIRTUAL WIDE: A 4:3 image is transformed into a 16x9 image to allow the user to watch SDTV on their 
widescreen.  
Options
Press Enter on selected feature to open the adjustment menu. 
Reset Adjustments: Use this function to reset all values of the current source back to factory default.
Language: There are 4 different menu languages are available: English, Spanish, French and German.
Picture Orientation: The projector could be installed on a ceiling or behind a screen, or with one or more mirrors. 
There are four settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.
Logo Light: To turn on or off projector logo light.
Active 
Image Area
Active Image Area
Runco CL-710
  > Video
     S-Video
     Component
     Component HD
     RGB HD
     DVI-I
     -----------------------
     Aspect Ratio
     Options
     Set Up
Options
     > Reset Adjustments
        Language
        Picture Orientation
        Logo Light
        Sleep Timer
        Lamp Hours
        OSD Position
        PC & HD Adj. 
						

							5. Menu Runco CL-710/ CL-710LT User’s Manual25 Sleep Timer: To setup auto off minutes. The setting timer is from 10 minutes to 3 hours.
Lamp Hours: To check for total time lamp age.
OSD Position: To adjust horizontal and vertical positions of OSD.
PC & HD Adj.: The following settings are only available with a PC or DTV RGB signal. There is no position adjustment 
when using DVI-D signal.
■AUTO: Adjusts the phase, frequency and position automatically.
■FREQ.: Adjusts the frequency of the signal.
■PHASE: Adjusts the phase of the input signal.
■H. POS.: Adjusts the horizontal position of the image.
■V. POS.: Adjusts the vertical position of the image.
Setup
The Setup menu is passcode protected and for the use by Runco personnel only. Many of the adjustments available in 
this section are intended for use by trained service personnel only. If you are having difficulty with one of these items, 
please contact your Runco Dealer for service. 
All items below which are printed in italic are intended for service personnel only. Non-italic items can be modified by 
the projector owner.
The CL-710 has four memory settings for color temperature. Three of these settings are factory set to defalt as 
follows:
Te m p  1 -- 5400 kelvin
Te m p  2 -- 6500 kelvin
Te m p  3 -- 7500 kelvin
The Temp 4 memory is installer adjustable and can be used to create custom settings. A passcode must be entered in 
order to change this setting. There are nine adjustable white balance parameters available for the Temp 4 setting. 
Once the desired adjustments have been entered, selecting store will save these custom settings into the Temp 4 
memory position.
Keystone: Corrects the trapezoidal distortion as a result of the angle of projection (-12° ~ +12°). This can correct for up to +/- 
12 degrees of offset.
Blue Image: This makes the red and green turn off.
Runco CL-710
  > Video
     S-Video
     Component
     Component HD
     RGB HD
     DVI-I
     -----------------------
     Aspect Ratio
     Options
     Setup
Setup
     > Keystone
        Blue Image
        White Balance
        Reset Lamp Timer
        Background Color 
						

							5. Menu Runco CL-710/ CL-710LT User’s Manual26White Balance: To adjust grey scale.  
Reset Lamp Timer: Use this function to reset lamp usage counter. Reset only if you replace a new lamp.
Background Color: To adjust background color to blue or white.
White Balance
        Red Gamma
        Green Gamma
        Blue Gamma
        Red Gain
        Green Gain
        Blue Gain
        Red Offset
        Green Offset
        Blue Offset
        Store
Adjust the Gamma Curve
Adjust High End
Adjust Low End 
						

							6. Additional Information Runco CL-710/ CL-710LT User’s Manual27
6. Additional Information 
Warning Message   
Replace the Lamp (Contact your Runco Dealer) 
■It is normal for lamp to be darker when this unit 
has been used for a period of time.
■ Lamp life is expired ! Please change a new lamp. 
And reset the lamp timer message will be 
displayed for 30 seconds on the screen if the lamp 
has operated for 950 hours.
■ Please change the lamp, Lamp will exceed its 
lifetime after (hours): message will be displayed 
on the screen for 30 seconds for each time turning 
on, if the lamp has operated for 980 hours. And 
the number will count down continuously.
■Please change the lamp ! message will display on 
the screen all the time and the POWER LED will 
blink in orange and green sequentially if the lamp 
has operated for more than (1,000) hours.
■The power will turn off automatically after 10 
minutes.
1. Loosen the screw of 
front lamp cover
  2. Take off the front lamp 
cover.
3. Loosen the two 
screws of lamp 
module. 4. Pull out the lamp 
module horizontally. 
5. Insert the new lamp 
module into this 
projector 
horizontally until it 
is securely in place.6. Tighten the two screws 
of lamp module.
Lamp life is expired !
Please change new lamp
And reset the lamp timer
Please change the lamp !
Lamp will exceed its 
lifetime after (hours):
Please change the lamp !
1
2