Runco Cl 710 Projector User Manual

							1. Overview Runco CL-710/ CL-710LT User’s Manual8 
Video
Composite video signal input
S-Video
S-Video signal input  
Comp
Component Y/C
B/CR input
Comp HD
DTV Y/P
B/PR signal input
RGB HD
DTV RGBHV signal input
DV I
Digital/ Analog signal input PBP (Picture by Picture)
Enable the PIP function.
ACTIVE
Switch to the active window in PIP 
display mode. 
PIP (Picture in Picture)
Enable the PIP function. Use 
ARROW keys to adjust the 
position of the PIP window (see 
PIP/ PBP function on page 20)
PIP+
Enlarge the size of PIP window.
PIP-
Shrink the size of PIP window.Arrow (c,e,d,f)
Use to select the menu or to 
make various adjustments. 
Enter
Enter the setting of items in the 
menu.
Picture
Access the Picture Setting menu 
(see Picture Quality 
Adjustments on page 23)
Info
Access the projector information
Exit
Exit and save the setting(s) of 
items in the menu.
Menu
Turns on/off the on-screen display 
menu. 
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual9
2. Installation
Remote Control 
Notes on Batteries
■Make sure that the battery polarities are correct when installing the batteries.
■Do not mix an old battery with a new one or different types of batteries.
■If you will not use the remote control for a long time, remove the batteries to avoid damage from battery 
leakage. 
Notes on Remote Control Operation
■Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver 
on the projector.
■The useable range is between 3m/ 9.8 feet (from the front of the projector) and 4m/ 13.1 feet (from the top of 
the projector) within 30 degree horizontal angle and 15 degree vertical angle.
Projector
❚Connect the Power Cord     
Push forward on the tap and lift to open the cover. 
Install the two AAA batteries with the correct 
polarity, then close the cover.  
Plug the supplied power cord into the AC inlet in the 
rear of this unit. (AC 100V ~ 240V)
Turn on the main power switch in the rear of this unit 
(next to the AC inlet). The POWER LED will light up 
in orange. Press ON key on the remote control for 
ONE second to turn on the unit. 
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual10❚
Adjust the Lens Zoom/Focus ring   
❚Adjust the height    
Adjust the projected image size you need with the 
zoom ring on the lens. To focus the image, rotate the 
focus ring on the lens.
There are 4 screw adjusters on the bottom of this 
unit. You can adjust the height or projection angle of 
this unit by using these adjusters.
Focus
Zoom outZoom in 
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual11
Installation For CL-710 (With 1.40 - 1.60 Lens)  
Screen  __________ (H)  x __________ (W)
C) VERTICAL OFFSET: 
Screen width x 0.052 = _________ inches from the center of the lens.
B) THROW DISTANCE: 
CL-710 16 x 9 Screens:
Minimum: (screen width x 1.40) =  __________ inches 
Maximum: (screen width x 1.60) =  __________ inches
Ceiling
Floor
  
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual12
Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens)
CL-710 @ 1280 x 720    
Screen Height Screen WidthMin Throw 
DistanceMax Throw 
DistanceVe r t i c a l  O f f s e t  
Po s i t i o n
40.5 72 100.80 115.20 3.74
43 77 107.80 123.20 4.00
45 80 112.00 128.00 4.16
47 84 117.12 133.86 4.35
49 87 121.80 139.20 4.52
50 89 124.60 142.40 4.63
51.5 92 128.80 147.20 4.78
52 93 130.20 148.80 4.84
54 96 134.40 153.60 4.99
56 100 140.00 160.00 5.20
58 103 144.20 164.80 5.36
58.5 104 145.60 166.40 5.41
60 107 149.80 171.20 5.56
61 109 152.60 174.40 5.67
63 112 156.80 179.20 5.82
65 116 162.40 185.60 6.03
67.5 120 168.00 192.00 6.24
72 128 179.20 204.80 6.66
80 142 198.80 227.20 7.38
82 146 204.40 233.60 7.59
90 160 224.00 256.00 8.32
Screen Hight Screen Width Min TD  Max TD  Vertical Offset
(SWx1.40) (SWx1.60) Screen Width x 0.052 
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual13
Installation For CL-710LT (With 1.85 - 2.40 Lens)
Screen  __________ (H)  x __________ (W)
C) VERTICAL OFFSET: 
Two inches offset means that the center of the projection lens is 2 above 
the top of the screen (inverted ceiling) or 2 below the bottom of 
the screen (upright floor mount).
B) THROW DISTANCE: 
CL-710LT 16 x 9 Screens:
Minimum: (screen width x 1.85) =  __________ inches 
Maximum: (screen width x 2.40) =  __________ inches
Ceiling
Floor
  
						

							2. Installation Runco CL-710/ CL-710LT User’s Manual14
Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens)
CL-710LT @ 1280 x 720    
Note: Two inches offset means that the center of the projection lens is 2” above the top of the screen (inverted ceiling) 
or 2” below the bottom of the screen (upright floor mount). Screen Height Screen WidthMin Throw 
DistanceMax Throw 
DistanceVe r t i c a l  O f f s e t  
Po s i t i o n
40.5 72 133.20 172.80 2.0
43 77 142.45 184.80 2.0
45 80 148.00 192.00 2.0
47 84 154.77 200.78 2.0
49 87 160.95 208.80 2.0
50 89 164.65 213.60 2.0
51.5 92 170.20 220.80 2.0
52 93 172.05 223.20 2.0
54 96 177.60 230.40 2.0
56 100 185.00 240.00 2.0
58 103 190.55 247.20 2.0
58.5 104 192.40 249.60 2.0
60 107 197.95 256.80 2.0
61 109 201.65 261.60 2.0
63 112 207.20 268.80 2.0
65 116 214.60 278.40 2.0
67.5 120 222.00 288.00 2.0
72 128 236.80 307.20 2.0
80 142 262.70 340.80 2.0
82 146 270.10 350.40 2.0
90 160 296.00 384.00 2.0
Screen Hight Screen Width Min TD  Max TD  Vertical Offset
(SWx1.85) (SWx2.40) 2.00” 
						

							3. Connecting Runco CL-710/ CL-710LT User’s Manual15
3. Connecting
When connecting, make sure to:
1. Turn off all equipment before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly connected. 
4. Connect all audio signals to external speakers. This projector is not equipped with speakers.
Connecting Video Inputs
❚Video / S-Video / Component (Interlaced Video)   
DVD Player 
						

							3. Connecting Runco CL-710/ CL-710LT User’s Manual16❚
Progressive Component (DTV Y/PB/PR)   
❚RGBHV (DTV RGB)
The RGB BNC input supports two kinds of HDTV formats: Progressive component (DTV Y/PB/PR) and DTV RGB. The 
unit will auto detect the resolution automatically.
DTV Source
DTV Source 
						

							3. Connecting Runco CL-710/ CL-710LT User’s Manual17
Connecting a Computer (DVI/ HDCP) 
This unit is compatible with the following computer resoultions: 1280x720, 1024x768, 800x600, 640x480.
PC or Notebook