Ruger Mini 30 Rifle Instruction Manual

32
1. Fold rear sight down. Disassemble one ring and reassemble over the scope
body between the turret and the eyepiece. Remember - the lug on the base
should be on the front side of the scope.
2. Install the four top screws. Do not tighten.
3. Disassemble the other ring and install it on the forward section of the scope
tube with the lug forwardly also. Install the four top screws. Again, do not
tighten.
4. Assemble the rings to the receiver with the lugs engaging the recesses in the
top surface of the...

33
SUGGESTED SIGHT PIC-
TURE
The front sight is aligned in the
center of the rear sight aperture
(“peep”) and the target (bullseye) is
positioned to appear as if it is sit-
ting on top of the front sight.
ELEVATION ADJUSTMENT:To move the bullet impact point upor down, move
the elevation slide (the “peep”) by loosening both its screws (using a small
screwdriver with a blade tip that exactlyfits the screw-head) only slightly so the
slide doesn’t move too freely. Move the slide in the direction you want the...

34
SHIPPING FIREARMS FOR REPAIR
RUGER®MINI THIRTY RIFLESreturned to the factory for repair
should be sent to: Sturm, Ruger & Company, Inc., Product Service Department,
411 Sunapee St., Newport, New Hampshire 03773. Telephone (603) 865-2442.
Guns should be sent prepaid. We will not accept collect shipments.
The Federal Gun Control Act, as well as the laws of most States and localities, do
not prohibit an individual (who is not otherwise barred from purchasing or pos-
sessing a firearm) from shipping a...

35
CAUTION: A gun containing modified, broken, malfunctioning,
or badly worn parts should not be fired.
ORDERING PARTS
Please contact the New Hampshire Product Service Department for parts avail-
ability and current prices. All parts orders for the RUGER®MINI THIRTY
RIFLEshould be sent to: Sturm, Ruger & Co., Inc., Product Service
Department, 411 Sunapee Street, Newport, New Hampshire 03773, 603-865-
2442. We cannot comply with open account or C.O.D. orders. Payment in the
form of a check, money order,...

36
RUGER
®
MINI THIRTY RIFLE
PARTS LIST
Design, prices and specifications subject to change without notice.
SPECIFY MODEL WHEN ORDERING
(See Exploded View on Page 41)
Part Name Part No. Model
*Barrel, Specify Model & Serial Number 0M8002 Mini Thirty - Blued Model
*Barrel, Specify Model & Serial Number K0M8002 Mini Thirty - Stainless Models
*Bolt MS01003 Mini Thirty - Blued Model
*Bolt KMS01003 Mini Thirty - Stainless Models
*Bolt Assembly MS11003 Mini Thirty - Blued Model
*Bolt Assembly KMS11003 Mini...

37
Part Name Part No. Model
Butt Plate Screw, (2 Req’d.) B-64 Mini Thirty - Wood Stock Models
Butt Plate Screw, (2 Req’d.) B-91 Mini Thirty - Synthetic Stock Model
Ejector Bolt Stop MS03211 Mini Thirty - Blued Model
Ejector Bolt Stop KMS03211 Mini Thirty - Stainless Models
Extractor MS01403 Mini Thirty - Blued Model
Extractor KMS01403 Mini Thirty - Stainless Models
Extractor Plunger KMS01600 All Mini Thirty Models
Extractor Spring MS01500 All Mini Thirty Models
*Firing Pin KMS01103 All Mini Thirty...

Part Name Part No. Model
Hammer Strut MS01800 Mini Thirty - Blued Model
Hammer Strut KMS01800 Mini Thirty - Stainless Models
Hammer Strut Assembly MS01800A Mini Thirty - Blued Model
Hammer Strut Assembly KMS01800A Mini Thirty - Stainless Models
Handguard Assembly, Fiberglass MFH All Mini Thirty Models
Magazine, Complete, 5-Shot Capacity MAG/762 All Mini Thirty Models
Magazine Bottom MS03404 All Mini Thirty Models
Magazine Bottom Retainer MS02602 All Mini Thirty Models
Magazine Follower MS03004 All Mini...

Part Name Part No. Model
Safety Assembly MS13800A Mini Thirty - Blued Model
Safety Assembly KMS13800A Mini Thirty - Stainless Model
Safety Detent Spring KMS04900 All Mini Thirty Models
Safety Spring Retaining Pin MS06200 Mini Thirty - Blued Model
Safety Spring Retaining Pin KMS06200 Mini Thirty - Stainless Models
Scope Ring Clamp D-74 Mini Thirty - Wood Stock Models
Scope Ring Clamp, Matte Finish KD-74M Mini Thirty - Synthetic Stock Model
Scope Ring Nut D-73 Mini Thirty - Wood Stock Models
Scope Ring...

40
Part Name Part No. Model
Sling Swivel, Front MS07500 Mini Thirty - Blued Model
Sling Swivel, Front KMS07500 Mini Thirty - Stainless Models
Stock (Wood w/Butt Plate Attached) MS00403 All Mini Thirty Models
Stock Assembly, Complete, Synthetic KMS30427 Mini Thirty - Synthetic Stock Model
Stock Reinforcement Assembly MS20702 Mini Thirty - Blued Model
Stock Reinforcement Assembly KMS20702 Mini Thirty - Stainless Model
Stock Reinforcement Lock Washer,  MS08000 All Mini Thirty Models
(2 Req’d.)
Stock...

41
RUGER®MINI THIRTY RIFLE 
EXPLODED VIEW