Home > Ruger > Firearms > Ruger Carbines PS9 Instruction Manual

Ruger Carbines PS9 Instruction Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Ruger Carbines PS9 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 48 Ruger manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							21
    ATTACHING RUGER SCOPE RINGS
    Each Ruger telescope ring is a mated assembly of a top and a base. Do not mix
    the parts of the two ring assemblies as they are not interchangeable. On the
    underside of each mounting ring assembly there is an integral lug, located off
    center with respect to the front and back sides of the mount. The lug is nearer to
    the front surface. By reference to the lug, the mounting ring can be correctly
    assembled with the front of the ring toward the muzzle of the rifle.
    1. Disassemble one ring and reassemble over the scope body between the turret
    and the eyepiece. Remember - the lug on the base should be on the front side
    of the scope.
    2. Install the four top screws. Do not tighten.
    3. Disassemble the other ring and install it on the forward section of the scope
    tube with the lug forwardly also. Install the four top screws. Again, do not
    tighten.
    4. Assemble the rings to the receiver with the lugs engaging the recesses in the
    top surface of the receiver. Tighten the clamp nuts so that the rings are locked
    to the semicircular cuts on the sides of the receiver.
    5. Rotate the scope until cross-hairs are aligned properly and slide scope to
    desired eye relief. Then tighten the eight top screws each a bit at a time to grip
    the scope body.
    6. Sight in according to the directions with your scope.
    SIGHT ADJUSTMENT
    The RUGER® CARBINErifles are equipped with an adjustable rear sight.
    Each click of the sight adjustment screw (either windage or elevation) will move
    the point of impact of the bullet approximately 3/4” at a range of 25 yards.
    Be careful not to use one of the curved front sight blade protectors as a front
    sight when you aim -- the front sight is a vertical post. 
    UP
    DOWN
    ELEVATION
    RIGHT
    LEFT
    WINDAGE
    To raisepoint of impact: turn screw
    counterclockwise.
    To lower
    point of impact: turn screw 
    clockwise.
    To move the point of impact to the right:
    turn screw counterclockwise.
    To move the point of impact to the left
    :
    turn screw clockwise. 
    						
    							Serrated
    Sight Base
    G06302
    Windage
    Adjustment - Screw
    G06250
    Lock Screw
    G06410
    (Must be loosened 1/2 turn prior to any sight adjustment)
    Aperture
    G06202
    Base Screw (2 Reqd)
    G06401Rear Sight Nut
    G06451
    WINDAGE ADJUSTMENT
    1.  Loosen Lock Screw approximately 1/2 turn.
    2. Windage Screw can now turn:
    a. Turn screw clockwise
    to move bullet point of impact to 
    the right
    .
    b. Turn screw counter
    clockwiseto move bullet point of 
    impact to the left
    .
    ELEV
    ATION ADJUSTMENT
    1.  Loosen Lock Screw onlyenough to permit Aperture to slide across serrations 
    on sight base.
    2. Aperture elevation can now be adjusted.
    a. Slide Aperture up
    Serrated Base to move bullet point of impact up.
    b. Slide Aperture down
    Serrated Base to move bullet point of impact down.
    T
    ighten Lock Screw when adjustments are completed.
    NOTE:Do notremove Lock Screw completely. Complete removal of sight from
    Carbine will be required to reinstall the Lock Screw so that the sight can be cor-
    rectly reassembled.
    R
    L
    SUGGESTED SIGHT PICTURE
    Top of front sight even with top
    of rear sight blade. Front sight
    centered in notch of rear sight
    blade. Target bulls-eye centered
    on top of front sight.
    GHOST RING SIGHT ADJUSTMENT
    For Rifles So Equipped
    22 
    						
    							23
    SERVICE AND PARTS POLICY
    If you have any question with regard to the performance of your RUGER®
    CARBINErifle please write or call (520-778-6555) our Product Service
    Department in Prescott, Arizona 86301, fully describing all circumstances and
    conditions involved. If you should return your rifle to the factory for repair, or
    order parts for it, please comply with the following suggestions for prompt serv-
    ice:
    WARNING: BEFORE SHIPPING ANY FIREARM,
    BE ABSOLUTELY CERTAIN THAT IT AND ITS MAG-
    AZINE ARE UNLOADED. DO NOT SHIP CAR-
    TRIDGES WITH A FIREARM.
    !
    SHIPPING FIREARMS FOR REPAIR
    RUGER®CARBINE rifles returned to the factory for repair should be sent
    to: Sturm, Ruger & Company, Inc., Product Service Department, 200 Ruger
    Road, Prescott, Arizona 86301-6181. Phone: (520) 778-6555.
    Guns should be sent prepaid. We will not accept collect shipments.
    The Federal Gun Control Act, as well as the laws of most States and localities, do
    not prohibit an individual (who is not otherwise barred from purchasing or pos-
    sessing a firearm) from shipping a firearm directly to the manufacturer for
    repair. However, before you ship your rifle to us, be certain that your State or
    locality does not have a law or regulation which will prohibit you from receiving
    the rifle from us after it has been repaired. If such receiving is prohibited, then
    please have a Federally Licensed firearms dealer ship the gun to us. If your rifle
    is sent to us by a dealer, it will be returned to him after being repaired. If a hand-
    gun (pistol or revolver) is shipped by an individual who does not hold a Federal
    Firearms License, it must be shipped via U.P.S. (Next Day Air) Persons who do
    not hold a Federal Firearms License are prohibited by Federal law from shipping
    a handgun by Mail. Handguns mailed in violation of the law are impounded by
    the Post Office.
    Please do not include rifle case, sling, telescopic sights or custom accessories
    with a firearm being shipped to the factory for service. DO NOT SEND GUN
    BOXES OR LITERATURE THAT YOU CONSIDER TO BE COLLECTOR’S ITEMS
    – THESE ARE INVARIABLY DAMAGED OR DESTROYED IN SHIPMENT.Rifles
    and shotguns may be shipped via Parcel Post. Always insure your shipment.
    Enclose a letter which includes your name, address, telephone number, serial
    number and model of the firearm. Describe in detail the trouble you have experi-
    enced with your firearm, or the work you wish to have done. Merely stating that
    the firearm “needs repair” is inadequate information. 
    						
    							It is the purchaser’s responsibility to be absolutely
    certain that any parts ordered from the factory are
    correctly fitted and installed. Firearms are compli-
    cated mechanisms and IMPROPER FITTING OF
    PARTS MAY RESULT IN A DANGEROUS MAL-
    FUNCTION, DAMAGE TO THE FIREARM, AND
    SERIOUS INJURY TO THE SHOOTER AND
    OTHER PERSONS. The purchaser and installer of
    parts must accept full responsibility for the correct
    adjustment and functioning of the pistol after such
    installation.
    PARTS MUST FIT CORRECTLY
    24
    !WARNING – PARTS PURCHASERS
    ORDERING PARTS
    Please contact the Arizona Product Service Department for parts availability and
    current prices. All parts orders for the RUGER®CARBINE rifles should be
    sent to: Sturm, Ruger & Company, Inc., Parts Department, 200 Ruger Road,
    Prescott AZ 86301-6181, (520)778-6555. We cannot comply with open account or
    C.O.D. requests. Payment in the form of a check, money order, Visa or
    Mastercard must accompany your order. Credit Card orders must include the
    account number, expiration date and whether it is a Visa or Mastercard account.
    Minimum parts order is $1.00 plus a $3.50 shipping and handling charge. Order
    parts by Part Number and Part Name, include the entire serial number of the
    firearm for which the parts are being ordered. There is a minimum net labor
    charge of $20.00 plus $12.00 shipping and handling charge if the parts are facto-
    ry fitted. All factory-fitted parts are fitted on an exchange basis only. We will not
    return the replaced parts.
    Because the CARBINEreceiver (part number G00125 or G00101) is a serial
    numbered component, it is defined as a “firearm” by Federal law and is not sold
    as a separate component.
    *Parts designated by an asterisk must be factory fitted. These parts are fitted on
    an exchange basis only. We will not return the replaced parts. We will not return
    any part that is broken, malfunctioning, badly worn or has been modified. See
    “Warning – Parts Purchasers” above.
    CAUTION: A gun containing modified, broken, malfunctioning,
    or badly worn parts should not be fired.!
    Work performed will bear a net minimum labor charge of $20.00 plus a $12.00
    shipping and handling charge. The charge for metal refinishing the RUGER®
    CARBINErifle is $50.00 plus a $12.00 shipping and handling charge. Custom
    gunsmithing service or nonstandard alterations are NOT AVAILABLE from
    Ruger Product Service Departments. 
    						
    							25
    RUGER
    ®
    CARBINE
    PARTS LIST
    Design, prices and specifications subject to change without notice.
    SPECIFY MODEL AND CALIBER WHEN ORDERING
    (See Exploded View on Pages 30).
    Part Name Part No. Model
    *Barrel G00325 PC9, PC9GR
    *Barrel G00300 PC4, PC4GR
    Barrel Band G06501 PC9, PC4
    Barrel Band G06510 PC9GR, PC4GR
    Barrel Band Assembly G06510-100 PC9GR, PC4GR
    Barrel Band Screw C-69H All Models
    *Bolt Lock G07301 All Models
    Bolt Lock Cross Pin, 2 Req’d G07900 All Models
    Bolt Lock Spring G09000 All Models
    Butt Plate Screw, 2 Req’d C-91SM All Models
    Cable Lock, 10” - For Ruger Rifles Only
    PM120A All Models
    Cocking Handle G02505 All Models
    Cocking Handle Plunger G07100 All Models
    Cocking Handle Plunger Spring G07200 All Models
    Disconnector G06701 All Models
    Disconnector Pivot Pin G06800 All Models
    Ejector G00802 All Models
    Extractor G01425 PC9, PC9GR 
    						
    							Part Name Part No. Model
    Extractor G01401 PC4, PC4GR
    Extractor Spring G01500 All Models
    Extractor Pin G01601 All Models
    Firing Pin KG01100 All Models
    Firing Pin Retaining Pin G06000 All Models
    Firing Pin Spring KV01850 All Models
    *Front Sight G05603 All Models
    Front Sight Cross Pin MA07201 All Models
    Ghost Ring Sight Adjustment Nut G06451 PC9GR, PC4GR
    Ghost Ring Sight Aperture G06202 PC9GR, PC4GR
    Ghost Ring Sight Assembly G06202-100 PC9GR, PC4GR
    Ghost Ring Sight Base G06302 PC9GR, PC4GR
    Ghost Ring Sight Base Screw, 2 Req’d G06401 PC9GR, PC4GR
    Ghost Ring Sight Installation Kit G06202-200 PC9, PC4
    Ghost Ring Sight Lock Screw G06410 PC9GR, PC4GR
    Ghost Ring Sight Windage Adjustment Screw G06250 PC9GR, PC4GR
    Guide Rod/Recoil Spring Assembly G15101 All Models
    *Hammer G01703 All Models
    Hammer Pivot Pin G01900 All Models
    Hammer Spring G04701 All Models
    Hammer Strut G01801 All Models
    Handguard Assembly G10500 All Models
    Handguard Plug, Not Illustrated G00551 PC9GR, PC4GR
    Lever Actuator G07501 All Models
    26 
    						
    							27
    Part Name Part No. Model
    Magazine, Complete P-18/10 PC9, PC9GR
    Magazine, Complete P-17/10 PC4, PC4GR
    Magazine Latch G03125 PC9 PC9GR
    Magazine Latch G03101 PC4, PC4GR
    Magazine Latch Retaining Pin G01200 All Models
    Magazine Latch Spring G05000 PC9, PC9GR
    Magazine Latch Spring G05050 PC4, PC4GR
    Pivot Pin Retainer G05501 All Models
    Rear Sight, Adjustable, Complete A15901-202 PC9
    Rear Sight, Adjustable, Complete A15901-203 PC4
    Rear Sight Body, Complete A15901-102 PC9
    Rear Sight Body, Complete A15901-103 PC4
    Rear Sight Body A05900 PC9, PC4
    Rear Sight Base A06100 PC9, PC4
    Rear Sight Base Set Screw A06200 PC9, PC4
    Rear Sight Blade G08701 PC9
    Rear Sight Blade, with White Outline Notch H07203 PC4
    Rear Sight Detent Ball MR05908 PC9, PC4
    Rear Sight Elevation Screw MR05902 PC9, PC4
    Rear Sight Elevation Spring MR05906 PC9, PC4
    Rear Sight Windage Adjustment Screw E05903 PC9, PC4
    Rear Sight Windage Spring MR05907 PC9, PC4✝Receiver Spacer G09900 PC9, PC4✝For PC9 rifles with serial numbers below 470-01666 and
    For PC4 rifles with serial numbers 480-02000 to 480-03110 
    						
    							Part Name Part No. Model
    Recoil Block G00703 PC9, PC4
    Recoil Block G00704 PC9GR, PC4GR
    Recoil Pad J05602 All Models
    Reversing Lever G07403 All Models
    *Safety G03803 All Models
    *Safety Plunger KG04800 All Models
    *Safety Plunger Spring G04900 All Models
    *Sear G02305 All Models
    Sear Interrupter G01300 All Models
    Sear Interrupter Plunger G05200 All Models
    Sear Interrupter Plunger Spring G05301 All Models
    Sear Spring G02401 All Models
    Sear Spring Plunger G05900 All Models
    *Slide G13725 PC9, PC9GR
    *Slide G13701 PC4, PC4GR
    Slide Stop Assembly G13202 PC9, PC9GR
    Slide Stop G03205 PC4, PC4GR
    Slide Stop Plunger KV06700 PC4, PC4GR
    Slide Stop Spring G04605 PC4, PC4GR
    Sling Swivel, Front S-85 PC9GR, PC4GR
    Sling Swivel Adapter, Front B08600 PC9GR, PC4GR
    Sling Swivel Rear Mounting Screw S-87 PC9GR, PC4GR
    Stock G00400 All Models
    Stock Bolt G05700 All Models
    28 
    						
    							Part Name Part No. Model
    Stock Bolt Bushing G08100 All Models
    Stock Bolt Lock Washer G06100 All Models
    Take Down Screw G09200 All Models
    Take Down Screw Flat Washer G09401 All Models
    Take Down Screw Lock Washer G09300 All Models
    Trigger KG02005 All Models
    Trigger Pivot Pin G02100 All Models
    Trigger Spring G02201 All Models
    Trigger Spring Support G03000 All Models
    *PARTS SO MARKED MUST BE FACTORY FITTED
    29 
    						
    							30
    RUGER®CARBINE
    EXPLODED VIEW
    *The receiver spacer (Part No. G09900) is for PC9 rifles
    with serial numbers below 470-01666 and for PC4 rifles
    with serial numbers 480-02000 to 480-03110. 
    						
    All Ruger manuals Comments (0)

    Related Manuals for Ruger Carbines PS9 Instruction Manual