Roland ColorCAMM PC 12 User Manual

							ColorCAMM PC-12
Tentative Users Manual
June, 2001
Ink Ribbon
This manual is describing about how to setup and work with Marketing sam\
ple machine of PC-12.
Marketing sample has limitation and differences from lot production as f\
ollows :
Specs., Appearance, Features
* Pacing, unpacking instruction and Users manual are not available.
* Windows driber does not support NT4.0/2000. (Beta will be completed o\
n the end of June, 2001)
* Windows driver is provided with FD. (CD-ROM for lot production)
* Sefety Srtandards will be available in lot production.
* Packing of blade holder, blade and cleaning pad is tentative.
* Paper tray has different color.
* Printing quality using stitching shall be improved.
Known Bugs
* PC-12 turns off unexpectedly when it fails to read cropmarks.
* Media feed Error during Cut Test does not cause ERROR indication.
* PC-12 locks up when opening cover during demo.
* Terms such as menu/button named in this manual may be different from W\
indows driver.
Use PC-60 Ink Ribbon cassette. You cannot use PC-600 cassette.
You can use both resin and wax types.
Downloaded From ManualsPrinter.com Manuals 
						

							power key:
Depress this to turn power ON/OFF.
ready/insert key:
Control Panels:
There are two keys and 3 LEDs on the top panel.
power LED:ready LED:
error LED:
Cover Eject Button:
Violet button on the right side
panel is release button of the 
Front Cover.
+ While ready LED turns ON(ready to receive data), depressing this key\
 to cause media feed.
If you keeps on depressing the key more than 1 second, media feed runs c\
ontinuously.
+ While depressing this key then depress the power button within 1 secon\
d, auto media cutting
works.
At this time, keep on depressing these keys to feed media properly.
+ Alert to indicate other error than hardware/mechanical error can be st\
opped by depressing this key.
If a cause of the error is not removed, alert does not stop.
+ When data transmission from host PC stops for 30sec., ready LED flas\
hes rapidly and you can
print only received data immediately by depressing this key. Buffer is c\
leared at the moment.
OFF >>> No error detected
Flash >>> Error
If your host PC is connected with bi-direction
mode, error is also indicated by driver.
ON >>> Power ON
Flash repidly >>> Printing Demo
Flash >>> Sleeping(Approx. 10min. no operation)
OFF >>> Power OFF
ON >>> Ready to receive data to print
Flash repidly >>> Data transmission interrupt
Flash >>> Printing
OFF >>> Pause printing
Downloaded From ManualsPrinter.com Manuals 
						

							Install Windows driver
Install Media Base
You can work with Windows 95/98/Me with this beta release.
USB support is available for Windows 98/Me.
If your host PC starts hardware wizard by Plug&Play : click [Cancel] but\
ton. You cannot install
Windows driver by hardware wizard.
+ When start-up display appears, click [Install].
+ Click [Agree] in license agreement.
+ Select port to use, LPT or USB.
+ When installation is finished, click [Done].
* If you like to change port, delete Windows driver first in
Control panel > Add/Remove Application. Or, you can
remove the Windows driver by Windows driver start-up >
Install > Setup type. 
Female for Nail on Media base
Screw Halls
Downloaded From ManualsPrinter.com Manuals 
						

							Install Ink Ribbon Casette
* Please be sure always that ribbon
does not get loose.
+ Select resin or wax properly in Windows driver.
+ Process Color
Be sure to install C, M, Y, K cassettes, and select [Standard] in Window\
s driver.
+ Spot Color
Install cassettes of color to use, and select [Spot Color] or [Full Colo\
r + Spot Color] in Windows
driver.
* Cassette Position
PC-12 reads type and color of cassete installed, so that you can install\
 cassettes at any cassette bay.
Be bery sure that you can install maximum 9 cassettes at a time.
If you install two or more same cassettes, PC-12 uses the left one first\
, and uses next one when the
first cassette gets ribbon-end.
+ Turn power OFF PC-12, then open the Front Cover by
depressing the Cover Eject Button.
+ Face up side B of the cassette(labeled side).
+ Place cassette to the target bay to push the violet nail
with the left side of the cassette. Then push the cassette
down.
+ Make sure all nails catch the cassette firmly.
If you will install a second cassette to the same bay, place
the second cassette over the first cassette and push them
down to be caught by three nails.
Gray nail
White nailViolet nail
Downloaded From ManualsPrinter.com Manuals 
						

							Install Blade Holder
Loading of Roll Media
+ Put a blade to the blade hoder as you do with XD-CH holder.
+ Put a media roll on the Media Base and adjust the position to the righ\
t limit indicated by the Stopper.
Downloaded From ManualsPrinter.com Manuals 
						

							When you remove the media, depress the Release Lever to have the Feeder to make media free.
You do not need to return the Release Lever manually. When you close the Front Cover, the Release Lever 
goes back to normal position.
+ Cut the front edgr of the media very straight along
the Cutter Guide.
+ Insert the media into the feeder to its limit(media
cannot go through the feeder).
+ Depress the ready/insert key to feed the media to
printing position.
+ Put the Media Cover over the roll and Media Base.
Align the rear edge of the Media Cover to be caught
by Media Base.
Downloaded From ManualsPrinter.com Manuals 
						

							Quick Print & Cut Guide from Adobe Illustrator 8
+ Open Document setup in File Menu.
+ Click Printer to open Printer setup dialog.
+ Click Properties in Printer dialog.
+ Roland PC-12 dialog appears. Click Media/Cutting tab.
+ Click User Size in Media/Cutting tab, then select User Size 
in pull-down menu.
+ Type width and length of printing size.
PC-12 requires margin as follows :
Printing size should be (media size - margin).
+ Click OK in User Size dialog.
Defined size is displayed in the Media/Cutting tab.
+ Click OK in Media/Cutting tab and Printer dialog.
+ Go back to Document setup dialog, and check Use Printer 
setup. 
+ Click OK to have AIs document size identical with Printer 
setup.
Define Cutting Line in Adobe Illustrator
+ Draw cutting line and apply a certain color to the cutting lines.
You can use any color and please record the RGB value of the cutting line.
*Please do not use other color definition than RGB.
+ Set line width at 0.01pt. 
In CorelDraw 9, select 0.001mm.
Cropmark	ON		OFF
Top		34.8mm		13.0mm
Bottom		44.0mm		31.0mm
Left		3.4mm		3.4mm
Right		3.4mm		3.4mm
Downloaded From ManualsPrinter.com Manuals 
						

							Print
+ Select Print from File menu.
+ Uncheck Bitmap print in Print dialog.
+ Click Properties. Roland PC-12 dialog appears.
+ Select Settling tab, and select Print&Cut for 
Output data.
+ Select Media/Cutting tab. Click [by color] radio 
button, then click color box.
+ Type RGB value in Color setting dialog. Then 
click OK.
* You can adjust brightness and contrast in Image 
tab.
+ Go back to Print dialog and click OK to start 
printing.
PC-12 carries Pre-feed first, then starts printing.
Status Monitor appears on the display to indicate the 
status of printing job.
Status, i.e. Printing
Click to cancel printingClick to pause 
printing
Click to restart printing
Monitor window of page 
processing
*PC-12 supports ECP fully.
Default setting of Windows driver is Standdard.
You can select High speed or DMA in Printer control panel. 
If you will use DMA for Roland_LPT1:, configure DMA channel for LPT1 at 1 or 3, and IRQ at 7.
Bi-direction option is ON in default setting.
Downloaded From ManualsPrinter.com Manuals 
						

							Windows Driver Options
Setting tab
[Output data]
- Print&Cut
- Print
- Cut
Cropmark check box
This is enabled when you select [Print]. Need to install black ink cassette.
[Document setup]
This works like Rendering intent of RCC.
- Auto: Color or gray scale is selected automatically.
- Color Photo: Fine black in Image tab is turned ON, and achieve natural halftone.
- Graphics: Suitable to reproduce solid color like red and blue.
- Gray scale: Halftone printing with black and white.
Save/Delete button
Current setting can be saved as a setting file.
Saved setting appears in the pull-down menu.
[Media type]
- Resin
- Wax
Save/Delete button
Adjustment button
You can customize printing density and cutting position to be suitable for your media.
[Print Mode]
Selection is different due to Media type selection.
Resin
- Standard
- High Quality
- White Ink: Undercover with White ink
- Reverse: YMCK > KCMY
Wax
- Standard
- DV Photo: High quality mode
- Glossy: Overcoat with Gloss finisher cassette
Downloaded From ManualsPrinter.com Manuals 
						

							[Printing method]
Standard: Process printing with CMYK 4 colors
Spot color: Print with selected color
Full color + Spot Color: Print with process color and spot color
[Ink cassette]
Selection will be changed due to selections in other items.
Media/Cutting tab
[Media size]
[Print direction]
- Portrait
- Landscape
- Mirror
[Media feed]
- Pagefeed check box: uncheck to feed backward to the top of the page
- Media cut check box: check to effect auto cutting at the end of a page
This option is disabled when Pagefeed is unchecked.
- Page margin: Specify margin between pages
[Cutting method]
- by color: specify with RGB only
- by line type
- All:cut all vectors in data
- No: all data is printed
- Polygon: default is on
If you cannot cut well, try with unchecking this option.
Polygon means drawing command, and do not read it as polygon in your drawing.
[Cutting setup]
Specify cutting speed and force.
Image tab
[Auto color adjustment]
You can select whichever Exposure or Digital camera
- Exposure: adjust exposure not influencing to color
- Digital Camera: adjust exposure and color
This option is disabled when selecting Spot color.
[Fineblack] 
Check to use both black ribbon and process black
- Photo only: use Fine black in photo image
- All: use Fine black in any type of object
Downloaded From ManualsPrinter.com Manuals