Ricoh Projector PJ WX4152N User Manual

• For details about the USB devices and files supported by the projector, see page 47 "Requirements
for Projecting Images from a USB Device".
• Do not disconnect the power cord when using the power timer function. The projector cannot start if
the power cord is disconnected.
Customizing a Slide Show You can customize the display effect and display interval for a slide show. These functions are useful for
decorating shop windows more effectively.
Changing the display effect for a slide show You...

1.
Select [Network/USB Settings], and then press the [ ] button.
2.
Select [USB Settings], and then press the [Enter] button.
3. Select [Settings], and then press the [ ] button.
4. Select [Display Effect], and then press the [Enter] button.
5. Select a display effect, and then press the [Enter] button. 6.
Press the [Menu] button.
7. Select [Reflect], and then press the [Enter] button.
8. Press the [Menu] button to close the menu screen.
Adjusting the slide show switching interval You can adjust the...

1.
Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [ ] button.
3.
Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the [ ] button.
5. Select [Display Interval (sec.)], and then press the [Enter] button.
6. Specify a slide show switching interval.
7. Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen. Projecting Images in a Slide Show
61 
CZE158    

Specifying the Sound Quality
You can select a sound quality setting for the built-in speaker that is applicable for the type of audio that
you are playing. This makes it easier to hear the audio that is playing.
Setting the Sound Quality for Giving a Presentation If [Narration] is specified for the sound quality, the projector plays dialog clearly. This mode is useful
when you give a presentation using the microphone connected to the projector, for example.
1. Press the [Sound] button. The sound quality...

5. Using the Projector via a Network
This chapter explains the settings for using the projector via a network. This chapter also explains the
operations that use QuickProjection.
Before Connecting to a Network
The projector does not support the Windows Vista and Windows 7 Network Projector function. Use
QuickProjection, which is the application provided with the projector for projecting images via a
network. For details about QuickProjection, see page 73 "Projecting a Computer's Screen via a...

1.
Insert the Ethernet cable into the Ethernet interface. 2.
Connect the other end of the Ethernet cable to a network device such as a hub. • The use of a shielded LAN cable is recommended.
Precautions for Using a Wireless LAN • Do not use a wireless LAN if there is electromagnetic interference from other equipment. Doing
so may cause an accident due to the other equipment malfunctioning from the electromagnetic
interference. Wireless uses radio waves to exchange information instead of an Ethernet cable....

The projector does not support the 5 GHz band.
• (mainly North America)
The projector supports 40 MHz channels only in the 5 GHz band and in the infrastructure mode. Before Connecting to a Network
65   

Connecting the Projector to a Network
To connect the projector to a network, you must specify network settings such as an IP address. The
required settings differ depending on the network environment and how you use the projector.
You can configure the required settings easily by using Network Setting Wizard. For details about how
to open Network Setting Wizard, see page 67 "Opening Network Setting Wizard".
To connect to a wired LAN
Connect an Ethernet cable to the projector, and then configure...

• If your wireless LAN access point uses WPA/WPA2-EAP as the authentication method, you must
set the current date and time and the time zone of the location where the projector is installed. For
details, see page 120 "Default Settings 2 Menu".
Opening Network Setting Wizard You can open Network Setting Wizard on the menu screen.
• If you configure both wired and wireless LAN settings using the Network Setting Wizard and your
wireless LAN access point uses WPA/WPA2-EAP as the authentication...

1.
Select [Wired LAN] on Network Setting Wizard, and then press the [Enter] button. 2.
Select [Disable DHCP (Manual Settings)] or [Enable DHCP (Auto Settings)], and then press
the [Enter] button.
If you select [Enable DHCP (Auto Settings)], proceed to Step 6.
3. Specify the projector's IP address.
4. Specify the subnet mask.
5. Specify the default gateway.
6. Select [Continue Wizard] or [End Wizard] on the confirmation screen, and then press the
[Enter] button.
To proceed to the wireless LAN...