Ricoh Projector PJ WU6181N User Manual

							116
DATE AND TIME SETTINGS
You can set the current time, month, date, and year.
NOTE: The projector has a built-in clock. The clock will keep working for about 2 weeks after the main power is turned off. If the main power is off for 2 weeks or more, the 
built-in clock will cease. If the built-in clock ceases, set the date and time again. The built-in clock will not cease while in the standby mode.TIME ZONE SETTINGS ...................... Select your time zone.
DATE AND TIME SETTINGS .......... Set your current date (MM/DD/YYYY) and time (HH:MM). 
INTERNET TIME SERVER ................ If you place a check mark, the projector’s built-in clock will be synchronized with an Internet 
time server in every 24 hours and at the time of projector’s startup.
UPDATE ...................................................... Synchronizes the projector’s built-in clock immediately. The UPDATE button is not available 
unless the INTERNET TIME SERVER check box is turned on.
SUMMER TIME SETTINGS ............. If you place a check mark, the clock for daylight saving will be enabled.
[MOUSE]
This function cannot be used in this device. It is used for future expansion purposes only.
5. Using On-Screen Menu  
						

							117
Disabling the Cabinet Buttons [CONTROL PANEL LOCK]
This option turns on or off the CONTROL PANEL LOCK function.
NOTE:
• How to cancel the [CONTROL PANEL LOCK]
  When the [CONTROL PANEL LOCK] is set to [ON], press the EXIT button or the INPUT button on the main body for about 10 seconds to cancel the [CONTROL PANEL LOCK] 
setting.
TIP: 
•  When the [CONTROL PANEL LOCK] is turned on, a key lock icon [ 
 ] will be displayed at the bottom right of the menu.
•  This CONTROL PANEL LOCK does not affect the remote control functions.
Enabling Security [SECURITY]
This feature turns on or off the SECURITY function.
Unless the correct keyword is entered, the projector cannot project an image. (→ page 36)
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
Selecting Communication Speed [COMMUNICATION SPEED]
This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 115200 bps. The default 
is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower \
baud 
rate may be recommended for long cable runs).
NOTE:
• Select [38400bps] or less when using the supplied software programs.
•  Your selected communication speed will not be affected even when [RESET] is done from the menu.
5. Using On-Screen Menu  
						

							118
Setting ID to the Projector [CONTROL ID]
You can operate multiple projectors separately and independently with the single remote control that has the CONTROL ID function. 
If you assign the same ID to all the projectors, you can conveniently operate all the projectors together using the single remote 
control. To do so, you have to assign an ID number to each projector.CONTROL ID NUMBER ........... Select a number from 1 to 254 you wish to assign to your projector.
CONTROL ID .................................. Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set-
ting.
NOTE: 
•  When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the 
buttons on the projector cabinet can be used.)
•  Your setting will not be affected even when [RESET] is done from the menu.
•   Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control ID.
Assigning or Changing the Control ID
1.  Turn on the projector.
2.  Press the ID SET button on the remote control.
  The CONTROL ID screen will be displayed.
 If the projector can be operated with the current remote control ID, the [ACTIVE] will 
be displayed. If the projector cannot be operated with the current remote control ID, 
the [INACTIVE] will be displayed. To operate the inactive projector, assign the control 
ID used for the projector by using the following procedure (Step 3).
Eternet
3. Press one of numeric keypad buttons while pressing and holding the ID SET 
button on the remote control.
 Example:
  To assign “3”, press the “3” button on the remote control.
  No ID means that all the projectors can be operated together with a single remote 
control. To set “No ID”, enter “000” or press the CLEAR button.
TIP: The range of IDs is from 1 to 254.
4.  Release the ID SET button.
  The updated CONTROL ID screen will be displayed.
NOTE: 
•  The IDs can be cleared in a few days after the batteries are run down or removed.
•    Accidentally pressing any one of the buttons of the remote control will clear currently specified ID with 
batteries removed.
Eternet
5. Using On-Screen Menu  
						

							119
Turning On or Off Remote Sensor [REMOTE SENSOR]
This option determines which remote sensor on the projector is enabled in wireless mode.
The options are: FRONT/BACK, FRONT, BACK. 
TIP:
• If the remote control system does not function when direct sunlight or strong illumination strikes the remote control sensor of the projector, change another option.
Enabling Key Sound and Error Sound [BEEP]
This feature turns on or off the button sound or alarm when an error occurs or the following operations are performed.
• Displaying the main menu 
•  Switching sources
•  Resetting data by using [RESET]
•  Pressing POWER ON or STANDBY button
5. Using On-Screen Menu  
						

							120
[NETWORK SETTINGS]
Important:
• Consult with your network administrator about these settings.
•  When using a wired LAN, connect the Ethernet cable (LAN cable) to the Ethernet port on the projector. (→ page 166) 
TIP: The network settings you make will not be affected even when [RESET] is done from the menu.
     About the Projector's [NETWORK SETTING].(→ page 6)
Hints on How to Set Up LAN Connection 
To set up the projector for a LAN connection:
Select [WIRED LAN] → [PROFILES] → [PROFILE 1] or [PROFILE 2].
Two settings can be set for wired LAN.
Next turn on or off for [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY] and select [OK] and press the ENTER button. 
(→ page 121)
To recall LAN settings stored in the profile number:
Select [PROFILE 1] or [PROFILE 2] for wired LAN, and then select [OK] and press the ENTER button. (→ page 121)
To connect a DHCP ser ver:
Turn on [DHCP] for wired LAN. Select [ON] and press the ENTER button. To specify IP address without using the DHCP server, 
turn off [DHCP]. (→ page 121)
To receive lamp replacement time or error messages via e-mail:
Select [ALERT MAIL], and set [SENDER'S ADDRESS], [SMTP SERVER NAME], and\
 [RECIPIENT'S ADDRESS]. Last, select [OK] and 
press the ENTER button. (→ page 123)
5. Using On-Screen Menu  
						

							121
WIRED LAN
PROFILES• The settings for using the built-in Ethernet port in the projector can 
be recorded in the projector memory in two ways.
•  Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] 
and the other options. 
  After doing this, select [OK] and press the ENTER button. This will 
store your settings in memory.
•  To recall the settings from memory:
  After selecting [PROFILE 1] or [PROFILE 2] from the [PROFILES] list.
  Select [OK] and press the ENTER button. 
•  Select [DISABLE] when not connecting to a wired LAN —
DHCP Place a check mark to automatically assign an IP address to the projector 
from your DHCP server.
Clear this check box to register the IP address or subnet mask number 
obtained from your network administrator. —
IP ADDRESS Set your IP address of the network connected to the projector when 
[DHCP] is turned off. Up to 12 numeric char-
acters
SUBNET MASK Set your subnet mask number of the network connected to the projector 
when [DHCP] is turned off. Up to 12 numeric char-
acters
GATEWAY Set the default gateway of the network connected to the projector when 
[DHCP] is turned off.  Up to 12 numeric char-
acters
AUTO DNS Place a check mark to automatically assign the IP address of your DNS 
server connected to the projector from your DHCP server.
Clear this check box to set the IP address of your DNS server connected 
to the projector. Up to 12 numeric char-
acters
DNS CONFIGURATION Set the IP address of your DNS server on the network connected to the 
projector when [AUTO DNS] is cleared. Up to 12 numeric char-
acters
RECONNECT Retry to connect the projector to a network. Try this if you have changed 
[PROFILES].  —
5. Using On-Screen Menu  
						

							122
PROJECTOR NAME
PROJECTOR NAMESet a unique projector name.  Up to 16 alphanumeric 
characters and symbols
DOMAIN
Set a host name and domain name of the projector.
HOST NAMESet a host name of the projector. Up to 15 alphanumeric 
characters
DOMAIN NAME Set a domain name of the projector. Up to 60 alphanumeric 
characters
5. Using On-Screen Menu  
						

							123
ALERT MAIL
ALERT MAILThis option will notify your computer of lamp replace time or error 
messages via e-mail when using wireless or wired LAN. 
Placing a checkmark will turn on the Alert Mail feature.
Clearing a checkmark will turn off the Alert Mail feature.
Sample of a message to be sent from the projector:
The lamp and filters are at the end of its usable life. Please replace 
the lamp and filters.
Projector Name: rdpj
Lamp Hours Used: 100 [H]  —
HOST NAME Type in a host name. Up to 15 alphanumeric 
characters
DOMAIN NAME Type in a domain name of the network connected to the projector. Up to 60 alphanumeric 
characters
SENDER'S ADDRESS Specify the sender’s address.  Up to 60 alphanumeric 
characters and symbols
SMTP SERVER NAME Type in the SMTP server name to be connected to the projector.  Up to 60 alphanumeric 
characters
RECIPIENT'S ADDRESS 
1, 2, 3 Type in your recipient’s address. 
Up to 60 alphanumeric 
characters and symbols
TEST MAIL
Send a test mail to check if your settings are correct.
NOTE:
•  If you entered an incorrect address in a test, you may not receive an Alert mail. Should this 
happen, check if the Recipient’s Address is correctly set.
•   Unless any one of the [SENDER'S ADDRESS], [SMTP SERVER'S NAME] or [RECIPIENT'S ADDRESS 
1-3] is selected, [TEST MAIL] is not available.
•  Be sure to highlight [OK] and press the ENTER button before executing [TEST MAIL].
 
—
5. Using On-Screen Menu  
						

							124
NETWORK SERVICE
HTTP SERVERSet a password for your HTTP server. Up to 10 alphanumeric 
characters
PJLink
This option allows you to set a password when you use the PJLink feature.
NOTE: 
•   Do not forget your password. However, if you forget your password, consult with your dealer. 
•  What is PJLink?
  PJLink is a standardization of protocol used for controlling projectors of different manufac-
turers. This standard protocol is established by Japan Business Machine and Information 
System Industries Association (JBMIA) in 2005.
  The projector supports all the commands of PJLink Class 1.
•  Setting of PJLink will not be affected even when [RESET] is done from the menu.
 
Up to 32 alphanumeric 
characters
AMX BEACON Turn on or off for detection from AMX Device Discovery when connecting 
to the network supported by AMX’s NetLinx control system.
TIP: 
When using a device that supports AMX Device Discovery, all AMX NetLinx control system 
will recognize the device and download the appropriate Device Discovery Module from an 
AMX server.
Placing a checkmark will enable detecting the projector from AMX 
Device Discovery.
Clearing a checkmark will disable detecting the projector from AMX 
Device Discovery.  —
CRESTRON ROOMVIEW: Turn on or off when controlling the projector from your PC.
CRESTRON CONTROL: Turn on or off when controlling the projector 
from your controller.
•  CONTROLLER IP ADDRESS: Enter your IP address of CRESTRON 
SERVER.
•  IP ID: Enter your IP ID of CRESTRON SERVER. Up to 12 numeric char-
acters
5. Using On-Screen Menu  
						

							125
[SOURCE OPTIONS]
Setting Auto Adjust [AUTO ADJUST]
This feature sets the Auto Adjust mode so that the computer signal can be automatic\
ally or manually adjusted for noise and 
stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE].OFF .................................... The computer signal will not be automatically adjusted. You can manually optimize the computer signal.
NORMAL ........................ Default setting. The computer signal will be automatically adjusted. Normally selec\
t this option.
FINE ................................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when 
[NORMAL]is selected.
TIP:
•  The default setting when shipped from the factory is [NORMAL].
•  When the AUTO ADJ. button is pressed, the same [FINE] adjustment is carried out.
[COLOR SYSTEM]
This feature allows you to select the TV video signal, which differs from country to country (NTSC, PAL, etc.).
This is set to [AUTO] by factory default. Set this if the projector cannot identify the signal automatically.
[AUDIO SELECT]
This selects the audio input of the HDMI 1 IN terminal, HDMI 2 IN terminal, DisplayPort input terminal and Ethernet port, USB A port.
When inputting analog audio, connect the audio output terminal of the connecting d\
evice with the BNC audio input terminal and 
set the Audio Select to “BNC”.
5. Using On-Screen Menu