Ricoh Aficio MP C3500 User Manual

Connecting to the Interfaces
11
1
Connecting to the IEEE 802.11b (Wireless LAN) Interface
Connect to the IEEE 802.11b (wireless LAN) interface.
Note
❒Check the settings of the IPv4 address and subnet mask of this machine.
❒For details about how to set the IPv4 address and subnet mask from the con-
trol panel of the machine, see Interface Settings.
Reference
p.59 “Network”
Setup Procedure
Set up IEEE 802.11b (wireless LAN) according to the following procedure:
AME006S
Downloaded From ManualsPrinter.com...

Connecting the Machine
12
1
Note
❒Select [802.11 Ad-hoc Mode] mode when connecting Windows XP as a wireless
LAN client using Windows XP standard driver or utilities, or when not using
the infrastructure mode.
❒You can specify either WEP or WPA to the Security Method.
❒Specify WPA, when [Communication Mode] is set to [Infrastructure Mode].
❒For details about how to specify wireless LAN settings from the control panel
on the machine, see IEEE 802.11b.
❒For details about how to specify wireless LAN settings...

Connecting to the Interfaces
13
1
❖When using in adhoc mode / 802.11 ad hoc mode
1. If the IEEE 802.11b interface unit is functioning, the LED lights up in or-
ange.
2. If it is connected properly to the network, the LED is green when in ad hoc
mode or 802.11 ad hoc mode. If the LED is blinking, the machine is searching
for devices. The LED will light after a few seconds.
Print the configuration page to verify settings.
Note
❒For more information about printing a configuration page, see Print List....

Connecting the Machine
14
1Network Settings
This section describes the network settings you can change with User Tools (Sys-
tem Settings). Make settings according to functions you want to use and the in-
terface to be connected.
Important
❒These settings should be made by the system administrator, or with the ad-
vice of the system administrator.
Settings Required to Use the Printer/LAN-Fax
This section lists the settings required for using the printer or LAN-Fax function.
Ethernet
This section lists...

Network Settings
15
1
Note
❒IPv6 can be used only for the printer function.
❒For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒[LAN Type] is displayed when the wireless LAN board is installed. If Ethernet
and IEEE 802.11b (wireless LAN) are both connected, the selected interface
has priority.
Reference
p.59 “Interface Settings”
IEEE 1394 (IPv4 over 1394)
This section lists the settings required for using the printer or LAN-Fax function
with an IEEE 1394...

Connecting the Machine
16
1
IEEE 802.11b (wireless LAN)
This section lists the settings required for using the printer or LAN-Fax function
with an IEEE 802.11b (wireless LAN) connection.
For details about how to specify the settings, see Interface Settings.
Menu User Tool Setting Requirements
Interface Settings/Network Machine IPv4 Address Necessary
Interface Settings/Network IPv4 Gateway Address As required
Interface Settings/Network Machine IPv6 Address As required
Interface Settings/Network IPv6...

Network Settings
17
1
Note
❒For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒[IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface
board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are con-
nected, the selected interface takes precedence.
Reference
p.59 “Interface Settings”
Settings Required to Use Internet Fax
This section lists the settings required for using Internet Fax.
Ethernet
This section lists the settings...

Connecting the Machine
18
1
Note
❒For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒[LAN Type] is displayed when the wireless LAN interface board is installed. If
both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected in-
terface takes precedence.
❒SMTP Server and Fax E-mail Account must be specified in order to send In-
ternet Fax.
❒When POP before SMTP is set to [On], also make settings for Reception Pro-
tocol and POP3 / IMAP4...

Network Settings
19
1
Note
❒[IEEE 1394] is displayed when the IEEE 1394 interface board is installed.
❒For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒SMTP Server and Fax E-mail Account must be specified in order to send In-
ternet Fax.
❒When POP before SMTP is set to [On], also make settings for Reception Pro-
tocol and POP3 / IMAP4 Settings.
❒When SMTP Authentication is set to [On], also make setting for Administra-
tors E-mail Address.
❒E-mail...

Connecting the Machine
20
1
IEEE 802.11b (wireless LAN)
This section lists the settings required for using Internet Fax with an IEEE
802.11b (wireless LAN) connection.
For details about how to specify the settings, see Interface Settings and File
Transfer.
Menu User Tool Setting Requirements
Interface Settings/Network Machine IPv4 Address Necessary
Interface Settings/Network IPv4 Gateway Address Necessary
Interface Settings/Network DNS Configuration As required
Interface Settings/Network DDNS...