Remington SPR 100 Shotgun Instruction Manual

							11
Instructions For Assembly Of Shotgun  (cont’d)
4. Now that the barrel has been locked into the receiver, you must reattach the fore end to the barrel.
Pull the forearm latch out and place the fore end on receiver.  With an upward swing motion lock the fore
end onto the barrel.  Do not force the fore end into its locked position.  While it may be necessary to push
the latch into its final flat position, never force the latch into position.  (See 
Picture 22).
Loading and Unloading Your Shotgun
WARNING
Never load or fire the shotgun unless the barrel is locked into position on the receiver, and the fore end is locked in to the receiver and barrel.
WARNING
Make sure the shotgun is pointed in a safe direction and the trigger block safety is engaged at all times while loading and unloading.
NEVER allow your fingers or other objects to contact the trigger while loading or unloading.
WARNING
Do not disengage the trigger block safety until you are ready to fire and have the gun pointed safely downrange
WARNING: DO NOT LOAD SHOTGUN UNTIL YOU ARE READY TO FIRE.
Picture 22
Picture 19Picture 20Picture 21 
						

							Loading and Unloading Your Shotgun  (cont’d)
TO LOAD:
1. Make sure the ammunition that you are using is the correct size and gauge.  The barrel is marked with the
gauge and chamber size.  Barrels marked 3” (76mm) will use only 2 3/4” (70mm) or 3”(76mm) shot shells
and must not be used with 3 1/2” (89mm) shells.  Barrels marked with 2 3/4” (70mm) will use only 2 3/4”
(70mm) and must not be used with or 3” (76mm) or 3 1/2” (89mm) shells.
2. Visually inspect the chamber and barrel for obstructions by breaking open the shotgun by depressing the
locking lever and tipping the barrel down.  The chamber and barrel should be free of oil or grease or
obstructions.  (See 
Picture 23).
3. After inspection, load the correct type of shot shell into the chamber making sure that the shells are flush
with the extractor (See 
Pictures 24and 25), then close the action by swinging the barrel up until it locks
into the receiver and the locking latch should move to its fully locked position (See 
Picture 26).  If the
locking lever does not move to the fully locked position, break open the action again and check to see if
the shot shell is fully seated in the chamber.  If the shell is fully seated then reclose the action. If the shot
shell is not fully seated, check the chamber for blockage and check the shell for deformation and retry
closing the action once more.  If the shell is the correct type and the chamber is not blocked and the shell
is not deformed and the locking lever does not move to its fully locked position (See 
Picture 27), unload
the gun (follow Unloading Instructions) and have a competent gunsmith look at the gun or return the gun
to Remington I.S.P. for inspection.  Do not force the shotgun closed.
12
Picture 23
Picture 24Picture 25
Picture 26Picture 27 
						

							Loading and Unloading Your Shotgun  (cont’d)
TO UNLOAD:
1. Break open the shotgun by depressing the locking lever and tipping the barrel down.  (See Picture 28).
2. Remove the shell from the chamber by grabbing it by the rim of the shell and pulling it form the
chamber.  (See 
Picture 29).
3. Visually check the barrel to make sure that it is free from obstructions.  (See 
Picture 30).
Firing Your Shotgun
WARNING: NEVER LOAD A CARTRIDGE INTO THE CHAMBER UNTIL YOU ARE READY TO FIRE THE SHOTGUN.
WARNING
Do not disengage the trigger block safety until the shotgun is pointed in a safe direction and you are ready to fire.
WARNING
If a cartridge does not fire and the trigger has been pulled and the trigger block safety is disengaged…Stop! And do the following: a) Make sure
the gun is pointed in a safe direction b) Engage the trigger block safety c) Wait 60 seconds d) Follow the instructions above for unloading the
shotgun.
If during firing the sound of any cartridge is noticeably softer or louder than the previous cartridge fired, Stop! Do not load another cartridge or
fire another cartridge and do the following: a)  Make sure the gun is pointed in a safe direction b) Engage the trigger block safety c) Follow the
instruction above for unloading the shotgun d) With the shotgun unloaded visually inspect the shotgun for barrel blockage or damage and
inspect the mechanical operation and receiver of the shotgun for damage before continuing.
READ, UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL
BEFORE FIRING THE SHOTGUN.
13
Picture 28Picture 29Picture 30 
						

							15
Firing Your Shotgun  (cont’d)
TO FIRE THE SHOTGUN:
1. Make sure the shotgun is pointed in a safe direction with the trigger block safety engaged.
2. Make sure you are wearing eye and ear protection.
3. Keep your fingers away from the trigger.  (See 
Picture 31).
4. Push the trigger block safety to the “off” or “fire” position with the red ring showing.  (See 
Picture 32).
4.With the butt stock held firmly against your shoulder and the barrel pointed towards your intended target,
place your trigger finger on the trigger.  The shotgun will fire when you pull or squeeze the trigger with
the requisite force.  (See 
Picture 33).
WARNING
Once you have fired the shotgun, immediately push the trigger block safety to the “on” or “safe” position.  Then follow the unloading
instructions above while keeping the muzzle pointed in a safe direction.
14
Picture 31
Picture 32
Picture 33 
						

							Instructions For Disassembly Of The Shotgun
1. Make sure the shotgun is unloaded (FOLLOW UNLOADING INSTRUCTIONS)  and pointed in a safe
direction.
2. Make sure the trigger block safety is engaged in the “on” or “safe” position.  (See 
Picture 34).
3. Remove the fore end from the barrel by pulling out the mechanical lever in the lower center of the fore
end and removing the fore end in a downward outward swinging motion.  Never force the fore end off the
barrel and receiver.  (See 
Picture 35).
4. With the barrel and receiver supported with one hand, depress the locking lever fully and tip the barrel
down until it disengages from the receiver.  Check the barrel for obstructions, damage and blockage after
removal.  (See 
Picture 36).
15
Picture 34
Picture 35
Picture 36 
						

							16
Manufacturer’s Warning
This firearm was manufactured to properly perform with the original parts as designed.  It is your duty to make
sure any parts you buy are correctly installed and that neither replacements nor originals are altered or changed.
Your shotgun has many parts that must relate correctly to other parts for safe and accurate operation.  Putting a
gun together wrong or with modified parts can result in a damaged gun, or personal injury or death to you or
others. Always let a qualified gunsmith work on your gun or at least, check any work not performed
by a gunsmith. Firearms safety is your primary concern. 
THE GUN OWNER MUST ACCEPT FULL
RESPONSIBILITY FOR THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM AFTER
ANY DISASSEMBLY OR REPLACEMENT OF PARTS.
To Clean and Maintain Your Shotgun
A. Follow procedures for unloading shotgun as described previously.
B. Follow procedures for disassembly of shotgun as described previously.
C. Materials needed to clean this shotgun are: a cleaning rod, cotton bore patches, brass bore brush,
powder solvent (such as Remington BriteBore
™), a small soft brush and good quality gun oil
(such as Rem®Oil).
WARNING
Lead or lead compounds are known to the State of California to cause cancer, birth defects, reproductive toxicity, and other serious physical
injury. Those who clean firearms should take protective measures to avoid contact or exposure to such chemicals.
D. Using the bore brush with powder solvent, scrub the interior of the barrel and chamber to remove any
powder and lead residue in the bore. Always and lastly, swab the interior of the barrel with a cotton patch
with gun oil to coat and protect the bore and chambers from rust and corrosion.
E.Any powder fouling on the firing wall, barrel, etc. can be easily cleaned with a brush and powder solvent.
F. All external surfaces should be wiped down with a light coat of rust preventative. Avoid using too much
oil as powder, dust or other foreign material may get trapped in the oil. This could lead to congealed
deposits which may interfere with the safe and reliable operation of this shotgun.
G.
USE CAUTIONwhile using solvents in gun bore cleaning. Prolonged or excess contact with
solvents can damage the gun’s bluing and finish. Be sure to wipe away all excess solvent and then 
lubricate with oil.
H.A gun should be cleaned after firing. In addition, external parts should be wiped with an oiled cloth
after handling. A light oil is ordinarily all that is necessary in cleaning if the gun has not been fired or fired
very little. If a gun is used frequently, it must be cleaned after each firing and regularly serviced by a
professional gunsmith. If the gun has been stored, remove all excess oil and/or grease before firing.
Always check to be sure that no cleaning patch or other obstruction remains in the bore or chambers
before firing. 
						

							17
DANGER – Ammunition Warning
Firearms may be damaged and serious personal injury or death to the shooter or bystanders may result from any
condition which contributes to the generation of excessive pressure or uncontrolled release of gas within the
firearm. Such adverse conditions can be caused by bore or chamber obstructions, propellant powder overloads or
by defective, incorrect or improperly loaded and assembled cartridge components. Even the strongest firearm can
be blown up as a result of excessive pressure. It is extremely dangerous to use a cartridge whose pressure is
greater than that developed by cartridges loaded to industry standards.
Ammunition (Cartridges) Notice
We specifically disclaim responsibility for any damage, injury or death occurring in connection with or as the
result of the use of the shotgun with faulty, nonstandard, remanufactured, hand loaded or reloaded ammunition
or with cartridges other than factory cartridges for which the shotgun was originally chambered.
Lubrication Warning
Firing a shotgun with oil, grease or any other material even partially obstructing the bore may result in damage to
the shotgun and personal injury to the shooter and those nearby.  Do not spray or apply lubricants directly on
ammunition. If the powder charge of a cartridge is affected by the lubricant, they may not fully ignite yet the ener
gy from the primer and/or powder may still be sufficient to push the projectile or wad into the bore where it may
become lodged. Firing a subsequent cartridge into the obstructed bore will damage the shotgun and may cause
personal injury to the shooter and those nearby.  Use lubricants properly.  You are responsible for the proper care
and maintenance of your firearm and ammunition.
PARTS AND SERVICE
To Order Parts
ALL PARTS ARE SUBJECT TO A $10.00 CHARGE FOR SHIPPING AND HANDLING. Some parts are restricted and
may only be installed by returning the shotgun to us.  When ordering parts, please state the Model, Gauge, Serial
Number, and Finish Color. For parts information, call (321) 6391432.
Service
To obtain information about returning your shotgun for service or repairs, call (321) 6391432.
One Year Limited Warranty
This shotgun is warranted to the original retail customer for one year from the date of retail purchase against
defects in material and workmanship. All parts and labor or replacement at our option are covered. The wood stock
is not covered by the one year warranty. The warranty on the wood stock is 60 days and is limited to the original
retail customer and extends 60 days from the date of retail purchase and covers only manufactured and material
defects. 
						

							19
PARTS AND SERVICE  (cont’d)
One Year Limited Warranty
Transportation to and from our repair facilities, government fees, damage caused by failure to perform normal
maintenance, sales outside the United States, damage caused by use of high velocity, high pressure, reloaded or
other nonstandard ammunition, or by any unauthorized repair, modification, misuse, abuse or alteration of the
shotgun is not covered by this Limited Warranty.
Implied Warranty
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law, which cannot be pre
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
To obtain warranty service, send your shotgun with proof of retail purchase, freight prepaid to:
REMINGTON I.S.P.
c/o USSG
402 Richard Road
Rockledge, FL  32955
NOTICE: It is illegal to ship a firearm with ammunition in the firearm or in the same packaging. Firearms and
ammunition must be shipped separately. For information about shipping ammunition, call (321) 6391432.
Your Owner’s Manual
Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and
safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy
of this manual from Remington upon request.
18 
						

							PARTS LIST
Model SPR100 Exploded View
1.  barrel with hook19.  receiver 37.  pusher
2.  sling swivel base20.  hinge pin 38.  base plate
3.  sling swivel ring 21.  firing pin dowel 39.  locking level detent spring 
4.  pin 22.  firing pin spring 40.  locking lever detent
5.  front sight 23.  firing pin 41.  locking lever detent pin
6.  extractor pin 24.  locking lever pin 42.  trigger guard
7.  extractor25.  locking lever 43.  trigger guard screw
8.  forend 26.  locking lever spring 44.  stock
9.  forend nut27.  locking lever spring pin  45.  screw
10.  hinge screw28.  indicator46.  washer
11.  forend hinge29.  hammer47.  butt plate
12.  hinge screw 30.  hammer pin 48.  woodscrew
13.  hinge screw 31.  sear 49.  woodscrew
14.  spring 32.  trigger 50.  stock sling swivel base
15.  catch housing33.  trigger pin51.  indicator spring
16.  forend catch 34.  trigger spring 52.  mainspring
17.  pin35.  trigger spring screw
18.  forend bushing 36.  safety
19 
						

							MODEL 100 EXPLODED VIEW ENLARGED
Model 100
1. barrel with hook
2. extractor spring
3. extractor
4. extractor pin
5. pin retainer
6. plunger
7. plunger spring
8. extractor sear
9. extractor sear pin
10. supporting pin
11. base plate 
12. receiver
Choke Tubes
WARNING
Never install or r
emove choke tubes while the firearm is loaded. Only install or remove choke tubes with the firearm unloaded, the action open
and the trigger block safely engaged.
Screw in Chokes Symbols/Markings
(This is an option – not all Model 100 shotguns have this feature)
The end of the choke tubes are marked with slashes to identify the choke construction:
/  Full
//  Improved Modified
/// Modified
//// Improved Cylinder
CI  Cylinder
WARNING
MAKE SURE YOU FULLY TIGHTEN THE CHOKE TUBE.
Shooting with a loose choke tube can cause damage to your shotgun.
2120