Remington 700, 710 Bolt Action Instruction Manual

							1
Ow ner
’s
Manual
Ow ner
’s
Manual
Instruction Book for: Instruction Book for:
Models 700, Seven & 710
Bolt Action Centerfire Rifles
page 2 ........the ten commandments of 
firearm safety
page 7 ........important parts of the firearm 
page 9 ........how to load and unload
page 12 ......lubrication and maintenance
page 15
......how to obtain parts and service
Models 700, Seven & 710
Bolt Action Centerfire Rifles
IMPORTANT!READ ALL INSTRUCTIONS
AND WARNINGS IN THIS
BOOK BEFORE USING THE FIREARM.   
						

							2
Eliphalet Remington’s first 
flintlock launched a proud tradition
of accuracy & responsibility.
1st COMMANDMENT
2nd COMMANDMENT
A Tradition of Performance and Safety.
In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or
better than any he could buy. His confidence was well founded. The barrel he handcrafted
set a new standard for firearm accuracy and spawned generations of products that have
made Remington
®Arms America’s leading gunmaker. While performance and style are 
certainly hallmarks of Remington firearms, one factor ultimately drives their performance.
Safety. Eliphalet Remington never lost sight of the fact that his rifles were potentially
lethal and could kill someone if handled improperly. And after more than 180 years the
same holds true for any firearm, including your new Remington. Eliphalet Remington’s
first flintlock launched a proud tradition of accuracy and responsibility.
Safety is Critical to Performance.
A superbly crafted gun is only as good as the hands that hold it. You can never be too careful. Shooting 
accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing to
fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can result
in the destruction of life, limb or property. There’s no calling back a bullet once it’s been fired, so it’s 
critical that you know the principles of safe gun handling and storage before you ever take your new Remington
firearm out of the box. 
The proper use and performance of your firearm depends on correct assembly and maintenance, so it’s critical
that you familiarize yourself with the information in this instruction book. Even if you’re a veteran shooter with a
collection of Remington firearms, take the time to read this literature. Not all firearms are the same. That means
the first step in safe handling is to learn the features and requirements of your new Remington.
THETENCOMMANDMENTS OFFIREARMSAFETY
The Ten Commandments of Firearm Safety should be etched in your memory forever. Let them govern your
action wherever and whenever you’re involved with firearms. In the field. On the range. Or in your home. Please
take the time to review and understand these rules.
Always Keep the Muzzle Pointed in a Safe Direction.
This is the most important gun safety rule. A safe direction is one in which an accidental 
discharge will not cause injury to yourself or others. Never allow your gun to point at 
anything you don’t intend to shoot. Be especially careful when you’re loading or unloading.
Treat every gun as if it were loaded. And make it a habit to know where the muzzle is 
pointed at all times, even when your firearm is unloaded. No one will be injured by an 
accidental discharge if you keep your firearm pointed in a safe direction. It’s as simple as that.
Firearms Should be Unloaded When Not Actually in Use.
Load your firearm onlywhen you’re in the field or on the target range and ready to fire. Never let a loaded gun
out of your sight or out of your hands. Unload it as soon as you’re finished shooting – before you bring it into
your car, camp or home. Remember, unloading your firearm means unloading it completely, so there is no
ammunition in the chamber or in the magazine. Before handling a firearm or passing it to someone else, visually
check the chamber, receiver and magazine to be certain they do not contain ammunition. Always keep the gun’s
action open when not in use. Never assume a gun is unloaded even if you were the last person to use it. Always
check for yourself. 
						

							Let common sense rulewhen you carry a loaded gun. If you’re in a situation that could risk
accidental discharge – such as crossing a fence, wading through a stream or climbing a 
tree – always unload your gun. Never pull or push a loaded firearm toward yourself or another
person. And never carry a loaded gun in a scabbard, detached holster or gun case.
Certain firearms(including some Remington
®rifles and shotguns) are equipped with internal
security devices to prevent unauthorized use. In addition, some firearms owners use external
devices, such as cable locks and trigger blocks, for the same purpose. Even if you use such
a device, you should still keep your firearm unloaded when stored or not in use. And
using internal or external devices cannot substitute, however, for securing your firearms
and ammunition in a separate, locked location.
Safe storage of firearmsis just as critical as safe handling. Never store guns loaded. Be
sure to keep your firearms in a secure place where unauthorized persons cannot get
their hands on them without your knowledge.
Take special careif there are children around. Kids are fascinated by guns. It’s a natural curiosity that can have
tragic consequences when not properly supervised. Store your firearms in a locked gun safe or some other location
that physically bars a child from gaining access. 
Ammunition should be storedand locked in a location separate from your firearm. Never leave an unsecured
firearm or ammunition in a closet, dresser drawer or under the bed. Remember, it is your responsibility to make
sure that children and others unfamiliar with firearms cannot get access to your firearm and ammunition. 
Don’t Rely on Your Gun’s Safety.
Treat every gunas if it can fire at any time, whether or not there’s pressure on the trigger. Your firearm has been
carefully designed to maximize performance and safety. However, because a gun’s safety is a mechanical device,
it could fail. 
Human error is a morelikely reason for a gun safety to fail. By mistake, you may think the safety is on when it
really isn’t. Or the safety may have been disengaged without your knowledge. Or you could think your gun is
unloaded when there’s actually a cartridge or shell in it. A mechanical safety is not a substitute for common
sense. It’s merely a supplement to your proper handling of a firearm.
Never touch the triggeron a firearm until you are ready to shoot. Keep your fingers away from the trigger when
you’re loading or unloading. And don’t pull the trigger when the safety is engaged or positioned between safe
and fire.
Before using your gun, read this instruction book to understand the exact location and operation of your firearm’s
safety. Even when the safety is on, maintain control of your loaded firearm and control the direction of the 
muzzle. In other words, don’t rely on your safety to justify careless handling. If your firearm’s internal 
mechanisms are broken or have been altered, your firearm may fire even when the safety is on. Remember, you
and your safe gun handling practices are your gun’s best safety.
Be Sure of Your Target and What’s Beyond It.
You can’t stop a shot in mid-air, so never fire unless you know exactly
where your shot is going and what it will strike. Never fire at a sound,
a movement or a patch of color. A hunter in camouflage can easily
be mistaken for a target by an impulsive shooter. Before you pull
the trigger be absolutely sure of your target and what’s behind it. Make
sure the shot has a backstop such as a hillside or dense material like sand.
Remember, bullets can travel great distances with tremendous velocity. Know how far your
shot will go if you miss your target or the bullet ricochets.
3
Firearms should be stored in a
secure place where children cannot
access them. A gun safe is an ideal
way to secure your firearm.
3rd COMMANDMENT
4th COMMANDMENT 
						

							Use Proper Ammunition.
Every firearm is designedto use a certain caliber or gauge of ammunition. Using the wrong ammunition, mixing
ammunition or using improperly reloaded ammunition can cause serious personal injury or death. And it only
takes one cartridge or shotshell of the incorrect caliber or gauge, or which has been improperly reloaded, to
destroy your firearm. It’s your responsibility to make sure the ammunition you use exactly matches the caliber or
gauge of your gun. Refer to this instruction book to find out the specific requirements of your firearm. Always
read and heed the instructions on ammunition boxes.
Confusing shellsor cartridges can cause serious personal injury or death and destroy your firearm. Examine
your shells or cartridges closely and use only the precise caliber or gauge for your specific firearm. For 
example, suppose you accidentally loaded a 20 ga. shell into a 12 ga. shotgun. Because the 20 ga. shell is too
small for the chamber, the 20 ga. shell could travel down the barrel and get lodged in the bore. If you then loaded
a standard 12 ga. shell behind it and fired, the 12 ga. shot will slam into the lodged 20 ga. shell and may cause
the barrel to explode right in your hand. This is commonly called a 12/20 burst, and it can kill you.
Check all ammunitionbefore you load it to make sure it matches your gun’s requirements. Every Remington
®
cartridge and shell is head-stamped with its caliber or gauge for easy identification. Likewise, you’ll find the 
caliber or gauge of your new Remington firearm imprinted on the barrel. 
Reloading Requires Extra Diligence.
If you’re an ammunition reloader, you are responsible for personally assuring that the loads and components of
your reloaded ammunition meet your gun’s factory-tested standards. Never use ammunition which has been
reloaded by someone else!
Many shooters handloadas a hobby or to save money on commercial, factory-made ammunition. However, it requires
a thorough knowledge of reloading procedures and a deep respect for the explosive potential of gunpowder.
Firearms are designed, manufactured and proof-tested to standards based on factory-loaded ammunition.
Handloaded or reloaded ammunition that deviates, either intentionally or accidentally, from load or component
recommendations can be very dangerous. 
Reloaders must observeall possible safety precautions and practices related to the proper handling of explosives.
Whether you’re a seasoned reloader or just starting out, you should study the subject, watch reloading demonstrations
and talk to experienced reloaders.
The first rule of reloadingis to always follow the manufacturer’s instructions for the components you’re using.
They’ll tell you to follow certain guidelines. Namely:
1. Don’t mix or substitute powders or primers.
2. Don’t use unknown or substandard components.
3. Use only suitable components that have been factory-tested 
by reputable ammunition, powder and bullet manufacturers.
4. Always be sure to use the manufacturer’s recommended recipe when reloading. 
Not following these guidelinescould result in severe injury to yourself or severe damage to your firearm.
Dangerously high pressure and explosions can result from an overcharge of powder or other deviations from
established reloading guidelines. Be very careful. The process of reloading exposes you to environmentally 
hazardous material. Lead, which is known to cause cancer and birth defects, is the most common substance 
in bullets and shot. It is important to handle lead bullets and shot with extreme care. Work only in a well-
ventilated area and always wash your hands after exposure and before eating. Never smoke while reloading.
Primers and powdersare also highly toxic and flammable. So after reloading be sure to clean up all materials
from your work area. Don’t leave primer or powder spills anywhere on the floor or bench top. Dispose of all waste
material in accordance with the manufacturer’s recommendations.
Finally, when reloadingor handloading concentrate on what you’re doing at all times. Do not be distracted by
talking to others, listening to the radio or watching TV while reloading. Never reload after consuming alcoholic
beverages or drugs of any kind. You are working with extremely hazardous materials and you can’t risk even a
few seconds of distraction. Remember, if you reload, you are the ammunition manufacturer and you are responsible
for the performance and safety of your reloaded ammunition.
4
5th COMMANDMENT 
						

							5
6th COMMANDMENT
7th COMMANDMENT
8th COMMANDMENT
9th COMMANDMENT
If Your Gun Fails to Fire When the Trigger is Pulled, Handle With Care.
If for some reasonthe ammunition doesn’t fire when you pull the trigger, stop and remember the 1st
Commandment of Firearm Safety – always keep the muzzle pointed in a safe direction. Keep your face away from
the breech, then put the safety on, carefully open the action, unload the firearm and dispose of the cartridge safely.
Remember that anytime there’s a shell in the chamber, your gun is loaded and ready to use. Even if you tried to
shoot and your gun didn’t fire, treat your firearm as if it could still discharge. 
Always Wear Eye and Ear Protection When Shooting.
Your sight and hearingrisk injury from shooting and should be protected at all times.
Wear protective shooting glasses to guard against falling shot, clay target chips, powder
residue, ruptured cartridge cases and even twigs and branches in the field. Also be sure
to wear eye protection when you’re disassembling or cleaning a gun so that tensioned
parts (like springs) and cleaning solvents don’t come in contact with your eyes. Continued exposure to shooting
noise can permanently damage your hearing. On the range, where shooting volume is the loudest, be sure to use
the maximum protection of a headset. And learn to use ear protection in the field, especially in confined loca-
tions like duck blinds.
Be Sure the Barrel is Clear of Obstructions Before Shooting.
Before loading your gun, open the action and make sure there’s no ammunition in the chamber or magazine.
Check the barrel for any obstructions or debris. Even a small amount of snow, mud, excess lubricant or grease
in the bore can dangerously increase pressure and cause the barrel to bulge or burst when firing. Use a 
cleaning rod and patch to wipe away anti-rust compounds or any other residues or obstructions in the barrel.
Never try to shoot out an obstruction by loading another shell and firing!
When firing, rely on your instincts. If the noise or recoil of your firearm seems weak, stop everything, unload
your firearm and be sure nothing is lodged in the barrel. Remember the 12/20 burst? That’s what can happen
when the barrel is obstructed. So always be sure you’re using the correct ammunition in your firearm and that
it’s free of obstructions.
Don’t Alter or Modify Your Gun and Have it Serviced Regularly.
Your firearm hasbeen designed to operate according to certain factory specifications. You’ll jeopardize your safety
and that of others around you by attempting to alter its trigger, mechanical safety or other mechanisms. So never
alter or modify your firearm in any way.
Like any mechanical device, a firearm is subject to wear. It must be maintained and
periodically serviced to assure optimum safety and performance. Only a qualified
service facility should service, repair or modify your Remington
®firearm. Consult
your instruction book for instructions on how to send your firearm to the factory or
for the location of the nearest Remington repair station.
Proper cleaning and lubricationare also important to firearm maintenance and are
necessary to assure accuracy, safety and reliability. Before cleaning, always make
sure that your gun is completely unloaded. And always clean the barrel from the
chamber end to the muzzle when possible. 
						

							Make it a practiceto clean your bore every time you’re going to shoot. Be sure to clean your entire gun before
and after long-term storage and no less than once a year. It’s also important to clean your gun whenever it’s been
exposed to adverse conditions such as rain, dirt, mud, snow, sleet or saltwater.
For safe and dependableoperation of your firearm, all parts of your gun must be properly cleaned and lubricated.
Periodically inspect the internal workings of your firearm to be sure they’re clean and free of rust, unwanted dirt
and debris. 
Use recommended lubricantson your gun and do not over-lubricate. Excessive use of a non-recommended
lubricant could adversely affect the function and safe operation of your firearm. Remember, you are responsible
for the proper care and maintenance of your firearm. Failure to properly maintain your firearm can not only 
damage or ruin your firearm, it can expose you and others to unnecessary risks of personal injury or death.
Remington
®has a wide rangeof firearm care products and resources for best results when cleaning your gun.
Everything from solvents and lubricants to rods and patches. They’re all available from your Remington dealer. 
Learn the Mechanics and Handling Characteristics of Your Firearm.
Not all guns are alike.They have different mechanical characteristics that dictate how you should carry and handle
them. Anyone who plans to use a firearm should first become totally familiar with the type of firearm it is and the
safe handling procedures for loading, unloading, carrying, shooting and storing it.
Before you even unpack your new Remington firearm, read this instruction book
from cover to cover and familiarize yourself with the different component parts of
the gun. Then read, understand and follow the Ten Commandments of Firearm
Safety in this book.
WARNING!Discharging firearms in poorly ventilated areas, cleaning
firearms or handling ammunition may result in exposure to lead, a 
substance known to cause birth defects, reproductive harm, cancer and
other serious physical injury. Have adequate ventilation at all times. Wash
hands thoroughly after exposure.
SHOOT SOBER!! 
There’s one other rulethat must be followed when handling firearms. In fact, respect for this rule is necessary in
order to effectively practice the Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER! Guns and
alcohol or drugs make a deadly combination. Never consume anything that would mildly impair your judgment
or physical coordination when you’re using a firearm. A staggering percentage of the shooting accidents that
occur every year involve alcohol or drugs. Be smart. Always shoot sober and stay alive.
WARNING!Failure to follow any of these safety rules may cause personal injury or death to the shooter or
bystander and damage to property. Do not use a firearm until you fully understand and practice the Ten
Commandments of Firearm Safety. If you have any questions about the safe use of a Remington firearm, write to
us at Remington Arms Company, Inc., Consumer Service, P.O. Box 700, Madison, NC 27025-0700, or call us at
1-800-243-9700.
DON’T KEEP THIS TO YOURSELF.
Now that you’re a gun owneryou have the obligation to help ensure that shooting sports are safe for everyone – 
participants and bystanders alike. You can do that by practicing these principles of firearm safety and passing them
on to others – especially new shooters. Set an example for beginners. Be a guide to their safe entry into the exciting
world of shooting sports. Invest your time and patience for the love of the sport and for its future. After all, it’s your
love of the sport that led you to buy a new Remington.
Firearm ownershipis a right and privilege. It’s a right guaranteed in this nation’s Constitution. It’s a privilege
which carries with it a personal responsibility to use your firearm in a way which will ensure your safety and the
safety of others. The preservation of this right and privilege depends on the personal commitment of you and
your fellow shooters to the safe and responsible use of firearms. Let the Ten Commandments of Firearm Safety
outlined in the book guide you at all times. Teach and promote these rules whenever you can. Remember, firearm
safety depends on you! That’s the only way to really enjoy your new Remington firearm and to preserve sport
shooting as we know it today. 
6
10th COMMANDMENT 
						

							Remington®Bolt Action Centerfire Rifle
Congratulations on your choiceof a Remington.®With proper care, it should give you many years of dependable
use and enjoyment. For best results, we recommend that you use Remington Ammunition – the ammunition used
in factory testing your firearm against our exacting function and performance standards.
Important Parts of the Firearm
The Safety Mechanism 
Note: All Remington Bolt Action Rifles function the same regardless of button appearance.
The safety mechanismprovides protection against accidental or unintentional
discharge under normal usage when properly engaged and in good working
order. The safety mechanism is not a substitute for following the rules of
safe gun handling.
To engage the safety mechanism, pull the safety mechanism fully to the rear
towards the ‘S’ position. See Picture 3.
Always put the safety mechanism in the ‘S’ position before handling, loading
or unloading the firearm. 
When you are ready to firethe firearm, push the safety mechanism forward towards the
‘F’ position to disengage the safety mechanism. See Picture 4.
Do not touch the triggerwhile moving the safety mechanism. Your fingers and all other
objects should be kept outside of the trigger guard and away from the trigger until you
are actually ready to fire by pulling the trigger.
Never pull the triggerwhen the safety mechanism is in the ‘S’ position.
WARNING!The firearm will fire when the trigger is pulled and the safety mechanism is in the ‘F’ position. 
Even when the safety mechanismis in the ‘S’ position, careless handling can cause the firearm to fire. SEE THE
TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2. 
The Security System
The firearm you have purchasedis equipped with an integrated security system which is
new to this product. This security system enables the owner to secure the bolt assembly
on the firearm in the action open position with the use of a special key.
7
PICTURE 1This picture shows the main parts of a REMINGTON BOLT ACTION RIFLE. The picture will aid in understanding the instructions in this book.
PICTURE 5
STOCK
TRIGGER
TRIGGER GUARDBOLT STOP RELEASEMAGAZINE FLOOR PLATEBARRELMUZZLE FRONT SIGHT REAR SIGHT EJECTION PORT
CHAMBERRECEIVER
SAFETY MECHANISM
BOLT HANDLEBOLT ASSEMBLY
SECURITY BUTTON
“J” SLOT
Cartridge Head
Primer
Caliber Marking
PICTURE 3
“
S” POSITION
PICTURE 4
“
F” POSITION
This picture shows the 
parts of the ammunition.PICTURE 2 
						

							J-KEYCAP
PICTURE 6
PICTURE 7
WHITE DOT
PICTURE 8
PICTURE 98
THIS SECURITY SYSTEM DOES NOT ELIMINATE THE NEED FOR SAFE GUN HANDLING AND STORAGE,
INCLUDING KEEPING THIS AND EVERY GUN UNLOADED AND LOCKED IN A SECURE PLACE WHEN NOT IN
USE. READ AND FOLLOW THESE AND OTHER SAFETY RULES IN THIS INSTRUCTION BOOK. FAILURE TO
READ, UNDERSTAND AND OBEY THESE RULES CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
SEE THE TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2.
The security system providedwith this firearm will not allow the bolt to be closed when the security system is
engaged. The existence of the security system does not change the function of the firearm’s safety mechanism.
See page 7.
Once the bolt assembly is installed, on the left side of the firearm you will see a security button on the bolt
plug of the bolt assembly. See Picture 5 on page 7.
On the security buttonthere is a “J’’ shaped slot. This “J’’ slot is the key hole for engaging and disengaging the
security system. Also on the sides of the security button you will see a RED and a WHITE indicator dot. When
the security button is viewed from the rear of the firearm, the dot indicates whether or not the security system
is engaged or disengaged. If the RED dot is visible from the rear of the firearm, the security system is disengaged
and the bolt can be cammed into the firing position. (See this page and page 9 for instructions on closing and
opening the bolt.) If the WHITE dot is visible from the rear of the firearm, the security system is engaged and
the bolt cannot be cammed into the firing position. The Model 710™ dot is viewed from the top.
To engage the security systemthe bolt must be installed in the firearm. 
NEVER ATTEMPT TO ENGAGE OR 
DISENGAGE THE INTEGRATED SECURITY SYSTEM WHEN THE BOLT IS CAMMED IN THE FIRING POSITION.
With
your new firearm you will receive two (2) keys. If your key has a cap, remove the cap before using. See Picture 6.
When the white dot is visiblefrom the rear of the firearm the security system is engaged.
To disengage the security system, push the key into the “J’’ slot with the bolt assembly
in the open position. BE SURE TO PUSH THE KEY IN AS FAR AS IT WILL GO. Once
the key is in place turn it counter-clockwise as far as it will go. From the rear of the
firearm you will now see a RED dot. Once the red dot is in place remove the key.
T
HE SECURITY SYSTEM IN NOW DISENGAGED AND THE BOLT CAN BE CLOSED AND CAMMED INTO THE
FIRING POSITION.
To engage the security system, FIRST ENSURE THAT THE BOLT IS IN THE
OPEN POSITION, then push the key into the “J’’ slot. Once the key is in place
turn it clockwise as far as it will go. From the rear of the firearm you will now see
a WHITE dot. See Picture 7. Once the white dot is in place remove the key. THE
SECURITY SYSTEM IS NOW ENGAGED AND THE BOLT CANNOT BE CAMMED
INTO THE FIRING POSITION.
IMPORTANT: ISS will not lock the firearm unless engaged with the bolt open.
Do not attempt to engage ISS when bolt is locked up.
In operating the security button, NEVER use excessive force to turn the key. If the key will not turn freely, contact
a Remington®authorized repair center.
Keep your security system engagedwhen your firearm is not in use. Keep your keys in a secure place, inaccessible
to others. DO NOT leave your keys or any ammunition with your firearm, which should be kept unloaded and
locked in a safe place. You know you have properly engaged the system when the bolt will not close.
If you lose the keysDO NOT attempt to disengage the security system using a foreign object. This will damage
your firearm. Contact your Remington authorized dealer for a replacement key. Even if you think the security 
system is engaged, careless handling can cause the firearm to fire. SEE THE TEN COMMANDMENTS OF
FIREARM SAFETY ON PAGE 2.
To Install Bolt Assembly: The bolt assembly locks
the cartridge into the chamber.
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Rotate the bolt stop counter-clockwise to the
vertical position (Model 710 only). See Picture 8.
BOLT STOP(UP)
BOLT STOP(DOWN) 
						

							9
SPECIAL NOTICE.220 SWIFT LOADING INSTRUCTIONS
Unlike other cartridges the .220 SWIFT 
is a semi-rimmed cartridge. Therefore, 
to ensure proper feeding, make sure 
that the rim of the top cartridge is 
ahead of the rim of the cartridge below.
RIGHT WRONG
4. Align the lugs on the bolt assembly with the receiver. See Picture 10.
5. Slide the bolt assembly into the receiver and push all the way in.
6. Rotate the bolt stop clockwise until it snaps into place (horizontal) (Model 710
™only).  See Picture 9 on page 8.
7. To place the bolt assembly in closed position, push the bolt handle down.
NOTE:The security system must be disengaged to close the bolt. 
Red dot will show.
To Remove Bolt Assembly:
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Do not touch the trigger while moving the safety mechanism.
4. Raise the bolt handle.
5. Rotate bolt stop counter-clockwise to vertical position (Model 710 only).
6. Pull the bolt handle all the way back.
7. Push bolt stop release in trigger guard. See Picture 10 (Model
Seven™/Model 700™ only). 
8. Slide the bolt assembly from the firearm.
The Trigger Assembly
The trigger is adjustedat the factory. All adjustments to the trigger assembly and firing
mechanism must be made by the factory or a REMINGTON®RECOMMENDED GUNSMITH.
WARNING!NEVER remove the trigger mechanism or make adjustments to the trigger or
trigger assembly. 
WARNING!NEVER put your finger on the trigger unless you are going to fire the firearm.
The Barrel
The inside of the barrelmust be clean and free of obstructions.
l. TO CHECK THE INSIDE OF THE BARREL:
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Pull the bolt all the way back.
5. Remove any ammunition from the chamber or magazine. See page 11.
6. Remove the bolt. 
7. Look through the inside of the barrel from the chamber end to the muzzle. See Picture 1 on page 7.
ll. TO REMOVE OBJECT FROM INSIDE THE BARREL: 
1. Use correct size cleaning rod.
2. Push cleaning rod from the chamber end all the way through the barrel, until the rod comes out of the muzzle.
3. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory
or a REMINGTON RECOMMENDED GUNSMITH.
WARNING!NEVER try to remove an object from the barrel by loading
another cartridge and firing. This may cause the barrel to burst or a 
cartridge case to rupture and cause serious personal injury.
lll. TO CLEAN THE BARREL FOLLOW THE INSTRUCTIONS
SHOWN ON PAGE 12.
Before loading the firearm, make sure the inside of the barrel is free of
dirt or other obstructions.
To Load the Firearm
There are three types of Model 700 rifles: one with a FLOOR PLATE, one
without a FLOOR PLATE and one with a DETACHABLE MAGAZINE BOX.
PICTURE 10
LUGS
BOLT STOP RELEASE 
						

							I. TO LOAD ONE CARTRIDGE ONLY:
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Pull the bolt handle all the way back.
5. Put one cartridge of the correct caliber on the magazine follower or in the chamber. See Picture 11.
6. Slide the bolt handle forward, then push the bolt handle down to lock the cartridge into the chamber.
THE FIREARM IS NOW LOADED.
7. To fire the firearm put the safety mechanism in the ‘F’ position.
THE FIREARM IS READY TO FIRE.
II. TO LOAD THE CHAMBER AND MAGAZINE:
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Pull the bolt handle all the way back.
5. Push four cartridges of the correct caliber, one at a time, into the magazine. If the firearm is a magnum,
you can only load three cartridges. If the firearm is a 17, 222, or 223 caliber, the magazine will hold five
cartridges. Keep the bullets aligned toward the chamber. See Picture 11.
6. Put one cartridge into the chamber.
7. Use your fingers to push the cartridges in the magazine all the way down. Slowly slide the bolt assembly
forward so that the bolt slides over the top of the cartridges in the magazine.
8. Push the bolt handle down.
THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED.
WARNING! Always check the cartridge for the correct caliber before loading the firearm. 
9. To fire the firearm put the safety in the ‘F’ position. 
THE FIREARM IS READY TO FIRE. 
ALTERNATE METHOD TO LOAD THE CHAMBER AND MAGAZINE:
(FOR MODELS 700
™ & 710™WITH DETACHABLE MAGAZINE BOX)
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Pull the bolt handle all the way back.
5. Press both magazine latches inward (Model 700) or one magazine latch (Model 710) and pull the 
magazine box from the firearm. See Picture 12.
6. Push four cartridges of the correct caliber, one at a time, into the magazine box, pushing the cartridges to
the rear of the magazine. If the firearm is a magnum, you can only load three cartridges. Keep the bullets
aligned toward the chamber. See Picture 11.
7. Place the magazine box into the trigger guard opening and push it until both latches (Model 700) or one
latch (Model 710) snap into the fully latched position. 
THE MAGAZINE IS NOW FULLY LOADED.
8. Put one cartridge of the correct caliber into the chamber. See Picture 11.
9. Use your fingers to push the cartridges in the magazine all the way down. Slowly slide the bolt assembly
forward so that the bolt slides over the top of the cartridges in the magazine.
10. Push the bolt handle down to lock the cartridge into the chamber.
THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED.
11. To fire the firearm put the safety mechanism in the ‘F’ position.
THE FIREARM IS READY TO FIRE. 
WARNING:
Always check the cartridge for the correct caliber before loading the firearm. 
10
PICTURE 11
LOAD CARTRIDGE AS SHOWN
PICTURE 12
NOTE: MODEL 710 HAS ONLY ONE LATCH ON THE STOCK
LOCATED AT THE TOP OF THE MAGAZINE FLOOR PLATE.PRESS BOTH MAGAZINE LATCHES INWARD