Remington 673 Instruction Manual

I. TO LOAD ONE CARTRIDGE ONLY:
1. Point the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Pull the bolt handle all the way back.
5. Put one cartridge of the correct caliber on the magazine follower or in the chamber. See Picture 11.
6. Slide the bolt handle forward, then push the bolt handle down to lock the cartridge into the chamber.
THE FIREARM IS NOW LOADED.
7. To fire the firearm put the safety mechanism in the ‘F’ position.
THE FIREARM IS...

To Unload the FirearmThere are three typesof Model 700™ rifles: one with a FLOOR PLATE, one without a FLOOR PLATE and one with a
DETACHABLE MAGAZINE BOX. 
INSTRUCTIONS FOR THE MODELS WITH A FLOOR PLATE:
1. Point the muzzle of the firearm in a safe direction.
2. Put the safety mechanism in the ‘S’ position.
3. Raise the bolt handle.
4. Put one hand over the top of the ejection port.
5. Slowly pull the bolt handle rearward with your other hand to
remove the cartridge from the chamber.
6. Hold cartridge and...

TELESCOPIC SIGHTS:
The top of the receiver has holes for the installation of telescopic sights.
Lubrication and Maintenance
When the firearm is to be stored, it should be carefully cleaned
and thoroughly oiled. Outside surfaces should be wiped with a
light coat of Rem
™Oil occasionally. When firearm is to be
reused, all excess lubrication must be removed. The chamber
and bore must be thoroughly wiped dry.
NOTE:Remington
®Rem™ Oil is available from your local dealer. If your dealer
is out of stock, ask...

11. Again thoroughly spray inside the trigger assembly at the four points
specified in Picture 17 with Rem™ Action Cleaner. Air dry or use com-
pressed air to thoroughly dry the trigger assembly.
12. Place a drop of Rem™ Oil in each of the four points in the trigger 
assembly specified in Picture 17.
13. Place the safety in the fire “F” position. Pull the trigger rearward and release
multiple times. Ensure the trigger returns completely to the forward position
each time.
If the trigger does not...

Cleaning Frequency
1. Before and after long term storage.
2. When the rifle has been subjected to adverse conditions such as shooting in the rain, snow, 
sleet or saltwater areas.
3. When the rifle is exposed to dirty conditions such as lying on the ground outdoors, being 
dropped in mud, etc. 
NOTE:While the Model 700
™and Model Seven™Stainless Synthetic Rifle have been designed and manufactured to 
provide improved corrosion protection, only proper care will keep your firearm in good operating...

How to Obtain Parts and Service From Remington®Arms Co. 
TO ORDER PARTS:
Many Remington®Dealersand Authorized Repair Centers carry a full line of parts. Please check with them first
before ordering parts.
To expedite your PARTSorder or request REPAIR SERVICE visit our web site at www.remington.com. Detailed
instructions are provided along with parts and/or service order forms. You may also reach Remington by calling
our toll free customer service number, 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 PM Eastern...

16
MODEL 700™
Bolt Action Centerfire Rifle 

17
1 Barrel Assembly
2 Bolt Assembly
3 Bolt Plug
4 Bolt Stop (Restricted)
5 Bolt Stop Pin (Restricted)
6 Bolt Stop Spring (Restricted)
7 Butt Plate
Butt Plate Frame (New Style Not Shown)
Butt Plate Insert (New Style Not Shown)
Butt Plate Frame Screw (New Style)
8 Butt Plate Spacer
9 Butt Plate Screw
10 Center Guard Screw ADL Grade
11 Ejector
12 Ejector Pin
13 Ejector Spring
14 Extractor
16 Firing Pin Assembly
17 Firing Pin Cross Pin
18 Floor Plate Latch, BDL Grade
19 Floor Plate Latch Pin, BDL Grade
20...

18
MODEL SEVEN™
Bolt Action Centerfire Rifle 

19
1 Barrel Assembly
2 Bolt Assembly
Bolt Final Assembly
3 Bolt Plug
4 Bolt Stop (Restricted)
5 Bolt Stop Pin (Restricted)
6 Bolt Stop Spring (Restricted)
7 Elevation Screw
8 Ejector
9 Ejector Pin
10 Ejector Spring
11 Extractor
Extractor 222 Cal.
12 Firing Pin (Restricted)
13 Firing Pin Assembly
14 Firing Pin Cross Pin
17 Floor Plate Latch
18 Floor Plate Latch Spring
19 Floor Plate Latch Pin
20 Floor Plate Pivot Pin
21 Front Guard Spring
22 Front Sight
Front Sight (Low)
23 Front Sight Ramp
24 Front Sight...