Quasar Vm L152 Operating Instructions Manual

11
Getting Started
Before Using
Remove Battery Pack before completing
the following steps:
1Undo strap ends
from buckles.
Attaching Shoulder StrapAdjust the Length of the
Shoulder Strap
Pull a loop of strap from buckle, then pull
strap tight to shorten or lengthen.
Adjust Hand Strap length to fit your hand as
shown.2Thread strap ends through Strap
Rings on Camcorder.
3Re-insert the strap
ends into buckles.
Hand Strap
123
min. 25.4 mm (1 inch)
Attaching the Lens Cap
Strap:
Thread the Strap through
the...

12For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Using MENU Mode
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA or VCR.
1Press MENU for MENU mode.
The CAMERA or VCR MENU screen (see below
left) appears when Menu mode is entered.
2Press UP or DOWN to highlight the
desired menu item.
3Press DISPLAY to set selection.
4Press MENU to exit.
Note:
• The Menu mode is canceled if 
UP/DOWN,DISPLAY, or MENU are not pressed...

13
Getting Started
Setting the Clock
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA or VCR.
Set the following items in order: Time
Zone, Daylight Saving Time, Date,
and Time.
1Press MENU for MENU mode.
Press 
UP or DOWN to select CLOCK SET .
2Press DISPLAY for
CLOCK SET menu.
Press 
UP or DOWN to
select TIME ZONE, DST,
or DATE/TIME.
3Press DISPLAY for menu of item selected in
step 2.
To change the setting:
TIME ZONE➔Go to step 3a on page 14.
D.S.T.➔Go to step 3b on page...

14For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Date and time including leap year are
calculated up to DEC 31, 2099.
Spring (First Sunday in April) :
ahead one hour.
Autumn (Last Sunday in October) :
back one hour. Clock will auto-adjust to daylight saving time (DST).
Setting the Time Zone
•When traveling, repeat this operation and
select one of the 8 listed time zones to
set the clock to local time.
Press 
UP or DOWN to
select OFF or AUTO.
Press...

15
Getting Started
Note:
• Using Light reduces battery operating time.
• Provide proper ventilation when using
Light extensively in a hot environment.
• Using Light when the Camcorder is
powered by a car battery may shorten
bulb life.
• Set Light to OFF when not in use. For recording in dim lighting.
Using the Light
Built-in Auto Light
1, 2, 3
CAUTION:
Light becomes hot.
Never cover Light while on.
LIGHT
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
A
EVF or LCD Monitor...

16For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Camera Recording
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab (page 10).
View recording scene on EVF (Electronic
Viewer Finder) or LCD (Liquid Crystal
Display) monitor.
Recording via EVF or LCD
Monitor
1Press LCD-OPEN to unlock the LCD
monitor. Swing LCD monitor fully open
and adjust viewing angle.
• If you want to record using EVF, close
and lock LCD...

17
Basic Operation
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab (page 10).
Camera Recording
1Set POWER toCAMERA.
2Press MENU for
MENU mode.
Press 
UP or DOWN
to select STAND-BY RELEASE .
3Press DISPLAY to select ON/OFF.
ON :From Stand-by mode, press
RECORD/PAUSE two times to
resume recording.
OFF :From Stand-by mode, set
POWER to OFF, then toCAMERA. Press RECORD/
PAUSE to record.
4Press MENU to exit.
Stand-by Quick Release
If left in RECORD/PAUSE mode for 5...

18For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before you begin...
• Connect Camcorder to power source.
Use AC Adaptor for longer recordings.
• Insert cassette with record tab (page 10).
• Set POWER to CAMERA.
Camera Recording
1Press MENU for MENU
mode. Press 
UP or
DOWN to select
PROGRAMMED REC .
2Press DISPLAY.
(Current time is
displayed.)
Each additional press
of 
DISPLAY increases
start time by 30 minutes.
3Press DOWN to select
REC TIME .
Press...

19
Basic Operation
Playing Back Recordings
Before you begin...
• Connect Camcorder to power source.
• Insert recorded tape.
Tracking Control
Quick Visual Search
Search Speed• SP   (Standard Play)     : 3 times normal.
• SLP (Super Long Play) : 9 times normal.
During playback, press:•FF     : fast forward search
•REW : rewind search
Press again or press PLAY for normal play.
Still Picture
Press STILL to freeze picture.
Press again for normal play.
This feature works best in SLP mode (page 10).
Special...

20For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playing Back Recordings
Connections
1Set POWER to:
VCR         view playback.
CAMERA view picture as it is
recorded.
2Turn TV ON and set to LINE INPUT.
See TV owner’s manual.
3Begin playback or recording.Audio/
Video Out
Connect Camcorder to a TV to view
playback or recordings in progress.
Before you begin...
• Connect Camcorder to power source.
• Make all TV-Camcorder connections.TV Playback or...