Proxima Projector Model DP5100 User Manual

UserÕs Guide  ¥  2Ð13 Chapter 2  ¥  Detailed Setup
Keystoning
The normal projected image will have a rectangular shape.
Keystoning is when the projected image becomes trapezoidal.
Normal ImageKeystoned Image
Figure 2-10
Normal vs. keystoned images
Keystoning occurs when the lens of the projector is not perpen-
dicular to the projection screen (the vertical plane) or when it is
not parallel to the floor (the horizontal plane). Keystoning also
occurs when the projector is tilted sideways.
To correct...

2Ð14  ¥  UserÕs Guide Chapter 2  ¥  Detailed Setup
The DP5100 is designed to minimize this effect while projecting
images high enough for the entire audience to view. An 8.8o
correction for keystoning is built into the projector. Use the
adjustable feet to raise and lower the front of the projector.
Figure 2-12
Adjusting the keystoning by rotating the feet 

UserÕs Guide  ¥  3Ð1 Chapter 3  ¥  Using the Desktop Projector
Chapter 3
Using the
Desktop
Projector
This chapter describes each of the keys on the control panel and
the remote control. It also explains the various projector settings
and how to change them.
The figure in the margin shows the control panel for the
DP5100.
STANDBY/ON Key
The STANDBY/ON key toggles the projection lamp on and off.
¥ STANDBY - Everything is on except the lamp and the fan.
¥ ON - The projector is in the projection mode.
INPUT...

3Ð2  ¥  UserÕs Guide Chapter 3  ¥  Using the Desktop Projector
FOCUS Key
The focus key adjusts the screen focus:
¥ N:  Near
¥ F:  Far
Three multi-function indicator lights on the projectors control
panel indicate the projectors current operating condition.
Figure 3-2
Control Panel Indicator lights
TEMP Indicator
The TEMP indicator light glows red in the unlikely event that the
projector reaches an over-temperature condition. A thermostat
will switch off power to the lamp until the projector cools....

UserÕs Guide  ¥  3Ð3 Chapter 3  ¥  Using the Desktop Projector
¥ Check the filter element. Clean or replace it if necessary. For
more information, please refer to Chapter 4, Maintenance.
¥ Check the rear exhaust vent. If the projector has reached an
overtemperature condition and the fan is working, you
should feel a strong rush of hot air from the vent. If the fan
is not working, the projector needs service.
After the projector returns to its normal operating temperature,
the TEMP indicator will go out....

3Ð4  ¥  UserÕs Guide Chapter 3  ¥  Using the Desktop Projector
The remote control is the primary control for the projector. It
contains all the key functions available on the Control Panel, and
performs additional functions not available on the Control Panel.
The remote control can be used up to 16 feet from the front of
the projector and within 30° to the left and right of the projector.
T INPUTSTANDBY
/ON
WVIDEORGB
MENUVOL
F
RESETCALL
N FOCUS ZOOM RGB
1/2 VIDEO
1/2
MENUMENU
HCHANGE
BLUE
BACKV
VOL...

UserÕs Guide  ¥  3Ð5 Chapter 3  ¥  Using the Desktop Projector
STANDBY/ON Key
The STANDBY/ON key toggles the projection lamp on and off.
¥ STANDBY - everything is on except the lamp and the fan.
¥ ON - The projector is in the projection mode.
RESET Key
The first time you turn the projector on, the factory settings are in
effect.
If you change any of these settings, then want to recall all of the
factory settings, press the RESET key.
CALL Key
The CALL key overlays a small image that identifies the...

3Ð6  ¥  UserÕs Guide Chapter 3  ¥  Using the Desktop Projector
ZOOM Key
The ZOOM key adjusts picture size.
¥ W:  Picture becomes wider.
¥ T:  Picture becomes telescopic (smaller).
FOCUS Key
The FOCUS key adjusts the screen focus.
¥ N:  Near
¥ F:  Far
MENU Keys
MENU
MENU
MENU
Figure 3-4
Menu keys
These four keys allow you to access and modify the DP5100
settings. Settings are viewed in the Menu Window, which appears
in the center of the projected image when your press the MENU
up or down keys.
In these...

UserÕs Guide  ¥  3Ð7 Chapter 3  ¥  Using the Desktop Projector
VOLUME Keys
The VOLUME keys on the remote control are used to adjust the
audio level of the projectorÕs internal speaker. Press the up or
down key to increase or decrease the speakerÕs audio level.
MUTE Key
Use the Mute key to momentarily shut down audio ouput from
the DP5100. Pressing MUTE again toggles the sound back on.
CHANGE Keys
The CHANGE keys control the image inversion feature.
¥ The H key flips the projected image horizontally, for...

3Ð8  ¥  UserÕs Guide Chapter 3  ¥  Using the Desktop Projector
MenusPressing the up or down MENU key brings the Menu Window to
the center of the projected image. The menus show the current
settings for the projector.
Displaying the Menu
Press the up or down MENU key once to display the menu. You
use these menus to adjust the projectorÕs image settings. The
menus vary depending on the current video source.
Selecting and Changing Settings
To move to and change a setting:
1. Use the up and down menu keys to...