Proxima Projector Dp1200x User Manual

							30 Advanced menu
Sharpness: (video sources only) changes the clarity of the edges of a video 
image. Select a sharpness setting.
Color Space: (computer sources only) allows you to select a color space 
that has been specifically tuned for the input. When Auto is selected, the 
projector automatically determines the standard. To choose a different set-
ting, turn off Auto, then choose either RGB, REC709 or REC601.
Color Temperature: changes the intensity of the colors. Select a listed set-
ting.
Color Control: allows you to individually modify each color. Highlight the 
color, press Select, then use the arrows to adjust the value.
Video Standard: (video sources only) When it is set to Auto, the projector 
attempts to pick the video standard automatically based on the input signal 
it receives. (The video standard options may vary depending on your region 
of the world.) If the projector is unable to detect the correct standard, the 
colors may not look right or the image may appear “torn.” If this happens, 
manually select a video standard by selecting NTSC, PAL, or SECAM from 
the Video Standard menu.
Overscan: (video sources only) removes noise around the video image.
The following 4 options are for computer sources only. 
Phase: adjusts the horizontal phase of a computer source.
Tr a c k i n g: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Sharpness
Color SpaceColor Temperature
Color Control
Video Standard 
						

							31
Settings menuAudio: allows volume adjustments. You can also adjust volume from the 
keypad.
Sources
: allows you to assign a particular input to a specific source key 
when using certain optional remotes. Also allows selection of a default 
Power-up Source and enables or disables Autosource. When Autosource is 
not checked, the projector defaults to the source selected in Power-up 
Source. If no source is found, a blank screen displays. When Autosource is 
checked, Power-up Source determines which source the projector defaults 
to at power-up. If no signal is present, the projector checks the sources in 
order until a source is found or until power down. 
Pow e r- u p  S o u r c e :  determines which source (computer or video) the projec-
tor checks first for active video during power-up. 
System menu
Rear: reverses the image so you can project from behind a translucent 
screen.
Auto Power: When Auto Power is checked, the projector turns on when 
power is applied and turns off if a source becomes inactive. 
Display Messages: displays status messages (such as “Searching” or 
“Mute”) in the lower-left corner of the screen.
Lamp Mode: allows you to optimize the lamp mode for your specific use. 
The default is High Bright, which maximizes the light output. Select Long 
Life to maximize lamp life and minimize fan noise, or Nominal to balance 
brightness, lamp life, and fan noise.
NND (Notebook No-Doze): prevents your notebook computer from going 
into Screen Save mode (functions only when the USB connector is plugged 
in).
Pow e r  S av e: automatically turns the lamp off after no signals are detected 
for 20 minutes. After 10 additional minutes with no signal, the projector 
powers down. If an active signal is received before the projector powers 
down, the image will be displayed. 
Audio
Sources
Power-up 
SourceSystem menu
Lamp mode 
						

							32
Screen Save: automatically blanks the screen with a black color after no sig-
nals are detected for a preset number of minutes (the default is 30 minutes). 
The image returns when an active source is detected or a remote or keypad 
button is pressed. Screen Save is disabled when Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen at startup and when no source is detected. 
Blank Screen: determines what color displays when no source is active.
Effect Key: allows you to assign a different function to the Effect button on 
the remote to quickly and easily use the effect. Only one effect can be 
enabled at a time. Highlight an effect and press Select to choose a different 
one. 
Blank: shows an empty screen. 
Mute: turns off all sound. 
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes sources to be reacquired.
Freeze: pauses the projected image.
Zoom: lets you magnify a part of the screen. This feature only works if 
you purchase an optional remote control with mouse buttons and cur-
sor control. To use the Zoom effect, press Effect, then press the left but-
ton to zoom the image, press the right mouse decrease the 
magnification. You can use the cursor control to pan the image, display-
ing different parts of it (only if the image is magnified). To return to the 
original size and cancel Zoom, press the Effect button a second time.
About: is the default effect. It displays the About menu.
Startup logo
Screen Save
Blank Screen
Effect Key 
						

							33
Language: allows you to select a language for the onscreen display of 
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default 
after displaying a confirmation dialog box.
Lamp Reset: resets the lamp hours counter in the About menu to zero after 
displaying a confirmation dialog box. Do this only after changing the lamp.
Service Code: only used by authorized service personnel.
LanguageService menu 
						

							34
MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner 
						

							35
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. Fifty hours before the specified end of the lamp’s life, 
the message “Change lamp” briefly appears on the screen at each startup. 
After 50 additional hours, the lamp will no longer light. You can order new 
lamp modules from your dealer. See “Accessories” on page 37 for informa-
tion.1
Turn off the projector and unplug the power cable. 
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down and loosen the two screws on the lamp 
door. Pry the door straight up to disengage the power interrupt connec-
tor (located on the underside of the door) and remove the lamp door. Be 
sure to pry the door straight up, not at an angle, to avoid damaging the 
power interrupt connector.
NOTE: The projector will not turn on while the lamp door is removed.
4
Pull the pull tab on the lamp module up to release the catch.
About
 menu
turn off and unplug
the projector
wait 60 minutes
remove lamp door screws
pry door off
release the pull tab 
						

							36 5
Pinch the lamp cable’s connector tabs to release the catch while pulling 
firmly on the connector to unplug the lamp.
WARNINGS: 
 To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.
 Do not drop the lamp module. The glass may shatter and cause injury.
 Do not touch the glass lamp screen. Fingerprints can obscure projection 
sharpness.
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing it.
6
Carefully remove the lamp module. Note that the lens end of the mod-
ule has a tab that connects in a slot in the bottom of the lamp cavity. You 
must pull upward with enough force to disconnect the tab from the slot. 
Dispose of the lamp in an environmentally proper manner. 
7
Install the new lamp module. Slide the new module straight down over 
the tunnel/hood, align the tab with the slot, then press to connect. 
8
Re-latch the pull tab while pressing down on the lamp module.
9
Re-plug in the lamp cable.
10
Replace the lamp door by aligning the connector on the back of the door 
with the projector and replacing the two lamp door screws.
11
Plug in the power cable, then press the Powe r button to turn the projec-
tor back on. Reset the lamp hour timer by simultaneously holding down 
the two Vo l u m e keys on the projector ’s keypad for 10 seconds. At that 
point the LED will turn green and you can power on the projector. You 
can also navigate to the Settings>Service menu and select Lamp Reset 
to reset the lamp timer. 
disconnect lamp cabletab on lamp module
slot on projector
reset lamp time in Service menu 
						

							37
AppendixAccessories
NOTE: Use only approved accessories. Standard Accessories
(ship with the projector)
Part Number
Protective Sleeve 110-0694-xx
Accessory Pouch 110-0693-xx
Shipping Box (with packaging) 110-0696-xx
Computer Cable 6.6 ft (2 m) SP-DVI-A
S-Video Cable 6 ft (1.8 m) 210-0125-xx
S-video to RCA Adapter 515-0027-xx
Audio Cable 6 ft (1.8 m) 210-0118-xx
Audio Cable Adapter 210-0177-xx
Power Cable (US) 10 ft (3m) 210-0255-xx
Power Cable (European) 10 ft 
(3m)210-0254-xx
Presenter Remote 590-0562-xx
Projection Lamp Module (included 
in projector)SP-LAMP-013
Quick Setup card 009-0791-xx
User’s Guide with CD 010-0457-xx
Technical Support Contacts Card 009-0658-xx
Safety Card 009-0659-xx
Color-coded Cable Ties, 3 set SP-CABLETIES
SCART Adapter 301130BOptional Accessories  Part Number
ATA Shipping Case CA-ATA-016
Soft Carry Case CA-C220
Digital Computer Cable 6 ft (1.8 m) SP-DVI-D
50” Diagonal Screen (portable) A650
60” Diagonal Screen (portable) HW-DLXSCRN
84” Diagonal Wall/Ceiling Mounted Screen HW-WALLSCR84
Portable Projector Stand SP-STND
Replacement Lamp Module SP-LAMP-013
MindPath RF PocketPoint Remote HW-RF-POCKTPNT
Conductor + Remote HW-CONDUCTOR +
Integrator Remote HW-INTEGRATOR
Wireless Connectivity Module LP-LITESHOW
Wireless Connectivity Module + PC Card LP-LITESHOWCARD 
						

							38
Red LED Behavior and Projector ErrorsIf the projector is not functioning properly and the red LED is blinking, con-
sult Ta b l e  2 to determine a possible cause. There are two second pauses 
between the blinking cycles. Visit our website for more details on the red 
LED error codes. See the inside back cover for contact details. 
Projected image sizeNOTE: Visit our website for an interactive image size calculator.
Table 2: 
Red LED Behavior Explanation
One (1) blink The lamp wont strike after five (5) 
attempts. Check the lamp and lamp door 
installations for loose connections.
Two (2) blinks The lamp counter hours have exceeded 
lamp life hours. Replace the lamp and 
reset the lamp hours counter.
Three (3) blinks The projector has shut down the lamp. 
Turn off the projector and wait one 
minute, then turn the projector on again.
 
Replace the lamp. Contact Technical Sup-
port for repair if replacing the lamp does 
not solve the problem.
Four (4) blinks The fan has failed. Contact Technical Sup-
port for repair.
Five (5) blinks The projector is overheating. Check for a 
blocked air vent. Contact Technical Sup-
port for repair if clearing the air vents 
does not solve the problem.
Solid red Unidentifiable error : contact Technical 
SupportTable 3: 
Range of distance to the screen for a given screen size
Diagonal 
Screen Size 
(inches/m) Distance to screen
Image Width
(inches/m)Maximum 
distance
(feet/m)Minimum 
Distance
(feet/m)
40/1 32/0.8 5.6/1.7 4.8/1.5
50/1.3 40/1 6.9/2.1 6/1.8
60/1.5 48/1.2 8.2/2.5 7.2/2.2
100/2.5 80/2 13.8/4.2 12.1/3.7 
						

							39
AAbout 32
accessories 5, 37
activation commands for laptops 7
Advanced menu 30
advancing slides 6
Aspect Ratio 32
audio 24
audio adapter 11
Audio In connector 6, 11
audio volume 13
Auto Image 22, 32
Auto Power 31BBlank Screen 32
blinking green 14
blinking red 14
Brightness 10, 28Ccleaning the lens 34
Color 13, 28
Color Control 30
Color Space 30
Color Temperature 30
colors are incorrect 20
computer connections
optional 6
required 6
computer image
optimize 25
Contrast 10, 13, 28DDisplay Messages 31
Drivers 8
USB 9
Windows 98 9EEffect Key 32
elevator foot 10
Ffirst time use
driver installation 8
focus 10, 13
Freeze 32
fuzzy image 17Iimage
displaying computer 7
displaying video 12
optimizing computer 25
optimizing video 26
image does not fit screen 19
image edges distorted 18
image not centered 21
image not sharp 18
image not square 18
image reversed 19
image size matrix 38
image torn 19
Interactive Display 5, 7, 14Kkeypad buttons 22
Keystone 10, 13, 22LLamp Mode 31
lamp replacement 35
lamp won’t turn on 20, 21
Language 33
laptop
connecting 6
external video port 7
LED
blinking green 14
blinking red 20
solid red 21
LED behavior 14, 38
lens cap, attaching 5
lens cleaning 34
Low Power 31