Proxima Pro Av 9400 Projector User Manual
Have a look at the manual Proxima Pro Av 9400 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 100 Proxima manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 ON-SCREEN DISPLAYRESOLUTIONH-Freq. (kHz)V-Freq. (Hz) 1024 x 768 60.023 75.03 XGA3 ON-SCREEN DISPLAYRESOLUTIONH-Freq. (kHz)V-Freq. (Hz) 70.09 31.47 720 x 400 VGA2 Specifications are subject to change without notice. NOTE:Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency and less than 200 MHz of Dot Clock. 0640 x 480 31.47 59.88 70.09 74.38 72.81 75.00 66.60 66.67 56.25 60.32 75.00 85.06 72.19 61.03 55.38 60.51 60.31 51.090 60.51 74.55 60.00 84.997 31.47 37.86 37.86 37.50 34.97 35.00 35.156 37.88 46.875 53.674 48.08 37.900 34.50 38.000 38.60 32.700 38.00 49.72 48.36 68.677 0640 x 400 640 x 480 0640 x 480 640 x 480 640 x 480 0640 x 480 800 x 600 0800 x 600 800 x 600 0800 x 600 800 x 600 0800 x 600 800 x 600 0800 x 600 800 x 600 0800 x 600 800 x 600 0832 x 624 1024 x 768 1024 x 768 VGA1 VGA3 VGA4 VGA5 VGA6 MAC LC13 MAC13 SVGA1 SVGA2 SVGA3 SVGA4 SVGA5 SVGA6 SVGA7 SVGA8 SVGA9 SVGA10 SVGA11 MAC16 XGA1 XGA2 70.07 74.92 60.02 54.58 79.35 87.1775.08 70.40 58.60 60.00 59.98 60.01 67.19 76.107 60.02 65.20 75.60 86.00 94.00 75.06 75.08 75.08 56.47 60.31 48.50 44.00 63.48 36.0060.24 64.20 62.50 63.90 63.34 63.74 71.69 81.13 63.98 61.20 71.40 50.00 50.00 68.68 75.00 80.00 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 7681024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1152 x 870 1280 x 960 1280 x 1024 XGA4 XGA5 XGA6 XGA7 XGA8 XGA9MAC19 77.07 62.04 1024 x 768 XGA10 75.70 61.00 1024 x 768 XGA11 86.96 35.522 1024 x 768 XGA1258.20 46.900 1024 x 768 XGA13 58.30 47.00 1024 x 768 XGA14 SXGA1 SXGA2 SXGA3 SXGA4 SXGA5 SXGA6 SXGA7 SXGA8 75.025 79.976 1280 x 1024 SXGA9 60.00 60.00 1280 x 960 SXGA10 SXGA11 SXGA12 SXGA13 SXGA14 MAC2160.18 63.79 1280 x 1024 SXGA1960.01 63.37 1280 x 1024 SXGA15 72.00 76.97 1280 x 1024 SXGA16 66.00 61.85 1152 x 900 SXGA17 86.70 46.43 1280 x 1024 SXGA18 MAC MAC (Interlace) (Interlace) (Interlace) (Interlace) (Interlace) 0640 x 480 VGA7 85.0043.2690 72.00 58.03 1024 x 768 XGA15 85.024 91.146 1280 x 1024 SXGA20 60.00 75.00 1600 x 1200 65.00 81.25 1600 x 1200 UXGA2 70.00 87.50 1600 x 1200 UXGA3 75.00 93.750 1600 x 1200 UXGA4 UXGA1 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS
42 COMPUTER MODE AUTO IMAGE SETTING DISPLAYMAIN MENU DISPLAY The Auto image function is provided to automatically adjust Fine sync., Total dots and Screen position for most computers. NOTE: This auto image function will be skipped when the incoming signal is digital. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select AUTO IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box AUTO IMAGE SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Move the arrow to an item(s) you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 5. Change the setting On , press the SELECT (REAR CLICK) BUTTON. 6. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Go! and then press the SELECT (REAR CLICK) BUTTON. The auto image function is started now. It will take about 10 seconds. 7. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, OK? is displayed for confirmation. 8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held even if the MAIN ON/OFF is switched off. 9. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON. 10.This setting is temporarily effective until you turn off the projector or change the input signal. NOTE: The fine sync., total dots and screen position of same computers may not be fully adjusted with the Auto Image Function. In that case, use the Picture Image and/or Picture Position adjustments (see pages 43 ~ 44) to make fine-adjust them after the Auto Image Function is executed. AUTO IMAGE FUNCTION
43 COMPUTER MODE IMAGE ADJUST DISPLAY TABLE OF PICTURE IMAGE ADJUSTMENT WHITE BALANCE (R/G/B) CONTRAST BRIGHTNESS 0127 63 63 0 63 0 0 TOTAL DOTS FINE SYNC The number of the total dots in one horizontal period. Adjust the number to match your PC image. Adjust the picture as necessary to eliminate flicker from the display. LIGHTERDEEPER DECREASE INCREASE DARKER BRIGHTERMAIN MENU DISPLAY NOTE: The projector may not reproduce a proper image for some UXGA signals. Since UXGA (1600 x 1200) image is converted to SXGA (1280 x 1024) image by partial scan, some lines and dots of the image do not appear. Some video noise of flicker on this compressed UXGA image cannot be eliminated even though you try to make a Fine sync adjustment. Picture adjustments have been preset at the factory. If you want to change the setting, operate the projector as follows. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings. 3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized in the table below. 4. Press the POINT DOWN BUTTON and a red arrow will appear. 5. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 6. To increase the level, point the arrow to sand then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to tand then press the SELECT (REAR CLICK) BUTTON. 7. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, OK ? is displayed for confirmation. 8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held even if the MAIN ON/OFF is switched off. 9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. 10.If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch is turned off. 11.To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed. PICTURE IMAGE ADJUSTMENT NOTE: Fine sync and Total dots will be skipped when the incoming signal is digital.
44 POSITION SETTING DISPLAYMAIN MENU DISPLAY 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select POSITION and press the SELECT (REAR CLICK) BUTTON. Another dialog box POSITION SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Move the arrow to a desirable direction ( , , or ) by pressing the POINT LEFT/RIGHT/UP/DOWN BUTTON(s) and press the SELECT (REAR CLICK) BUTTON to a desirable picture position. 5. You may want to store the settings to the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, OK ? is displayed for confirmation. 6. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held even if the MAIN ON/OFF is switched off. 7. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. 8. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch is turned off. 9. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed. COMPUTER MODE PICTURE POSITION ADJUSTMENT
45 COMPUTER MODE MAIN MENU DISPLAY This projector can automatically detect most display signals from most personal computers currently distributed. However, some computers adopt a special signal format which is different from the standard one and the projector cannot detect it. If this happens, the projector cannot reproduce a proper image. And a flickering picture, a non-synchronized picture, a non- centered picture or a skewed picture may be projected instead. For those non-standard formats, this projector is provided with PC ADJUST, enabling you to precisely adjust several parameters to match with the input signal format. The projector has eight independent memory areas where you can store the parameter you have set. This enables you to recall the setting for a specific computer when you need it. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON. Another dialog box Where to reserve will appear. 3. In this dialog box, you will select one of the memory areas from among Mode 1 to Mode 8. If parameters have been previously set and stored in the memory, the status Stored will appear on the corresponding row. If not, Free will appear. 4. Press the POINT DOWN BUTTON and a red arrow will appear. 5. Move the arrow to one of the Modes (Free position) where you want to store the parameters by pressing the POINT UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) BUTTON to select it. NOTE : If Stored appears in all Modes, no new PC parameter data can be stored. In this case, clear the PC parameter data using Mode free Function. PC ADJUSTMENT NOTE: This function will be skipped when the incoming signal is digital.
OK ? Ye s No630 1056 47 4 46 ITEM TOTAL LINES TOTAL DOTS HORIZONTAL VERTICALFUNCTION The number of the total vertical lines. Adjust the number to match your PC image. The number of the total dots in one horizontal period. Adjust the number to match your PC image. Adjustment of the horizontal picture position. When the image is not centered on the screen, adjust this. Adjustment of the vertical picture position. When the image is not centered on the screen, adjust this. PC ADJUSTMENT DISPLAY 1MAIN MENU DISPLAY 6. Another dialog box PC ADJUSTMENT DISPLAY 1 will appear and the parameter data for the Mode you have selected is shown in this dialog box. 7. The parameters will be filled with the data determined by the projector according to the present signal input. 8. The function of the parameters and their values are summarized in the table as below. 9. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 10.To increase the level, point the arrow to sand then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to tand then press the SELECT (REAR CLICK) BUTTON. 11.If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. 12.To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed. 13.To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. 14.If you quit the MENU without storing the settings in the memory, the parameter data you changed will not be kept. 15.The stored settings are permanently held even if the MAIN ON/OFF is switched off. 16.Adjust the data such as a Clamp, Display area, Horiz. scale and Vert. scale if needed, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select (t). Press the SELECT (REAR CLICK) BUTTON. COMPUTER MODE
XGA 47 ITEM CLAMP DISPLAY AREA HORIZ. SCALEFUNCTION Adjustment of the clamp level. When the image has a dark bar, try this adjustment. Expanding or compressing level for the vertical direction. Expanding or compressing level for the horizontal direction.PC ADJUSTMENT DISPLAY 2MAIN MENU DISPLAY 17. Another dialog box PC ADJUSTMENT DISPLAY 2 will appear and the parameter data for the Mode you have selected is shown in this dialog box. 18. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). 19. To increase the level, point the arrow to sand then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to tand then press the SELECT (REAR CLICK) BUTTON. 20. If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. 21. To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, OK ? is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed. 22. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. 23. If you quit the MENU without storing the settings in the memory, the parameter data you changed will not be kept. 24. The stored settings are permanently held even if the MAIN ON/OFF is switched off. VERT. SCALE Adjustment the display area to match your PC. COMPUTER MODE Adjust the display area, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select ( ) and press the SELECT (REAR CLICK) BUTTON. Another dialog box DISPLAY AREA DISPLAY will appear. Move the arrow to an item that you want to select display area by pressing the POINT UP/DOWN BUTTON(s) and press the SELECT (REAR CLICK) BUTTON. Selected mode data will be displayed in H, V box. To close dialog, move the arrow to Quit and press the SELECT (REAR CLICK) BUTTON.
OK ? Ye s No630 1056 47 4 Stored Stored 48 MAIN MENU DISPLAY PC ADJUSTMENT DISPLAY MODE FREE The Mode free function is provided to confirm or clear the parameter data produced by PC ADJUST. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON. Another dialog box Where to reserve will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Move the arrow to one of the Modes (Stored position) that you want to confirm by pressing the POINT UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) BUTTON. Another dialog box PC ADJUSTMENT DISPLAY will appear. 5. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON. 6. To modify the parameter data, perform the steps 9 ~ 24 of PC ADJUSTMENT SECTION. 7. To clear the parameter data, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Mode free. Press the SELECT (REAR CLICK) BUTTON. OK? is displayed for confirmation. 8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON to clear the parameter data. 9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. COMPUTER MODE
49 COMPUTER MODE This projector can adjust the image size and pan the image with PICTURE SCREEN ADJUSTMENT. 1. Press MENU BUTTON and MAIN MENU DISPLAY dialog box will appear. 2. Press POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON. Another dialog box SCREEN ADJUST DISPLAY will appear. 3. Press POINT DOWN BUTTON and a red arrow will appear. SCREEN ADJUST DISPLAYMAIN MENU DISPLAY 4. To adjust the image size or pan the image, move the arrow to Digital zoom by pressing POINT UP/DOWN BUTTON(s) and then press SELECT (REAR CLICK) BUTTON. MAIN MENU DISPLAY and SCREEN ADJUST DISPLAY will disappear. The D.zoom and the magnifying-glass icon is displayed to indicate Digital zoom mode. lThis projector cannot display in the resolution more than 1600 x 1200. If your computers screen resolution is higher than 1600 x 1200, reset the resolution to the lower before connecting the projector. lThe image data of VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768) or UXGA (1600 x 1200) is modified to fit the screen size in the initial mode. lWhen the original image size is larger than the screen size (1280 x 1024), this projector becomes Digital Zoom mode automatically. l The maximum size in expand mode is 4 times as large as the original screen size. (When original image size is smaller than the screen size (1280 x 1024) . l The maximum size in expand mode is 3.5 times as large as the screen size (1280 x 1024). (When original image size is larger than the screen size (1280 x 1024). l The minimum size in compress mode is the screen size (1280 x 1024) in SXGA or UXGA mode,1024 x 768 in XGA mode, 800 x 600 in SVGA mode or 640 x 480 in VGA mode. l Panning function can work only when the image is expanded. l The normal Panning Operation may not function properly if the computer system prepared with the PC Adjust is used. PICTURE SCREEN ADJUSTMENT D. zoom 5. Move the magnifying-glass icon by pressing the POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) BUTTON(s). 6. To expand the image, press SELECT (REAR CLICK) BUTTON. The image is magnified by degrees (Expand function). 7. To compress the image size, press FRONT CLICK button on the remote control.The size of image is reduced by degrees (Compress function). 8. To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) BUTTON(s). Move the magnifying-glass icon to screen end then the image move to the direction indicated (panning function). 9. To cancel the Digital Zoom mode, press other buttons (Except NORMAL and CURSOR BUTTONS). 10. Press the NORMAL BUTTON in Digital zoom mode, the image size changed to the screen size (1280 x 1024). 11. Press the CURSOR BUTTON in Digital zoom mode, the magnifying-glass icon is disappears on the screen. However, the Digital Zoom mode is held. 12..To turn the image size to true size (1280 x 1024 in SXGA or UXGA, 1024 x 768 in XGA, 800 x 600 in SVGA and 640 x 480 in VGA), move the arrow to True by pressing POINT UP/DOWN BUTTON(s) and then press SELECT (REAR CLICK) BUTTON. The image size is turned to the true size.
50 OTHER FUNCTION SETTING This Projector is designed for connecting with USB Port of the computer or peripheral equipment that is to be standard. When this function is in the (Mouse) position, you control the pointer of the computer used the projectors wireless remote control unit. When this function is in the (Control) position, you control the projector by computer. NOTE:Before you control the projector by computer, install USB driver (optionally saled parts) and set up the computer following instruction in the USB driver package. Contact your authorized dealer or service station. This projector has other functions setting: Blue back, Display, Reverse T/B, Reverse R/L, Split wipe, Power management, USB, Remote control and Lamp age. TB TB LRLR BLUE BACK (On or Off) SPLIT WIPE (On or Off) REVERSE L/R (On or Off) REVERSE T/B (On or Off) DISPLAY (On or Off) USB (Mouse or Control) POWER MANAGEMENT (On or Off) When this function is in the On position, the projector will project a blue image without video noise on the screen when the video source is unplugged or turned off. When this function is in the On position, on-screen displays always appear when adjustments are made. Although these on-screen displays are very helpful, these may spoil the view if adjustments are made during presentations. To avoid this, you can keep back certain displays by switching this function Off. The followings are the displays that you can hide. l Wait Displayl Mode Displayl Volume Display l Mute Displayl Zoom/Focus/Lens shift Displayl D.Zoom Display l Normal Displayl No show Display When this function is in the On position, the top/bottom picture reverse. Turn SPLIT WIPE function On in the SETTING menu. The picture will change into next one by sliding black image side ways when the input source is changed. Change the input source by MODE button. The picture is replaced by black image from side ways to the center, and the next one appears from the center to side ways like drawing the black curtains. Turn POWER MANAGEMENT function On in the SETTING menu. The projector is power save mode. In this mode, the projector LAMP is automatically off when no signal of the source for 5 minutes. Incoming the signal is again, the projector LAMP is automatically on. When this function is in the On position, the left/right picture reverse capability lets you project onto a rear projection screen.