Proxima Dp8200x Projector User Manual

							30
Picture menuTo adjust the following six settings, highlight the setting, press Select, use 
the up and down arrows to adjust the values, then press select to confirm 
the changes.
Ve r t i c a l  K e y s t o n e: adjusts the image vertically and makes a squarer image. 
You can also adjust vertical keystone from the keypad.
Horizontal Keystone: adjusts the image horizontally and makes a squarer 
image. 
Contrast: controls the degree of difference between the lightest and darkest 
parts of the picture and changes the amount of black and white in the 
image.
Brightness: changes the intensity of the image.
Color: (video sources only) adjusts a video image from black and white to 
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the 
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. 
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or 
down to fill the display area.
increasing keystone
decreasing keystone
Vertical Keystone
Horizontal KeystoneAspect Ratio 
						

							31
Presets: The provided Presets optimize the projector for displaying com-
puter presentations, photographs, film images, and video images. (Film 
input is material originally captured on a film camera, like a movie; video 
input is material originally captured on a video camera, like a TV show or 
sporting event.) You can use the preset as a starting point, then further cus-
tomize the settings for each source. The settings you customize are saved in 
the preset for each source. To restore the factory default settings, choose Fac-
tory Reset in the Settings>Service menu. 
There are also three user-definable presets. To set a preset for the current 
source, adjust the image, then choose Save User 1, 2, or 3. You can recall 
these settings in the future by selecting the appropriate user presets. 
Room Lighting: This features optimizes the projector for your room’s light-
ing conditions. Select Dark if you are in a dark room, Light if in a bright 
room. Choosing Light maximizes the light output from the projector.
Presets
Room Lighting 
						

							32 Advanced settings
Sharpness: (video sources only) changes the clarity of the edges of a video 
image. Select a sharpness setting.
Color Space: This option applies to computer and component video 
sources. It allows you to select a color space that has been specifically tuned 
for the video input. When Auto is selected, the projector automatically 
determines the standard. To choose a different setting, turn off Auto, then 
choose RGB for computer sources, choose either SMPTE240, REC709 or 
REC601 for component video sources.
Color Temperature: changes the intensity of the colors. Select a listed 
value, or select User and individually adjust the intensity of the red, green, 
and blue colors.
The following 4 options are for computer sources only. 
Phase: adjusts the horizontal phase of a computer source.
Tr a c k i n g: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
SharpnessColor SpaceColor Temperature 
						

							33
Settings menuAudio: allows adjustments to the volume, bass, treble and balance. Also 
allows you to turn on and off Loudness (which boosts the higher and lower 
frequencies), the Internal speakers, and projector startup Chime.
Sources
: allows you to assign a particular input to a specific source key 
when using the optional Integrator remote. Also allows selection of a 
default Startup Source and enables or disables Autosource and RGB. 
Sources>Startup Source: this determines which source the projector 
checks first for active video during power-up. 
Sources>Autosource: When Autosource is not checked, the projector 
defaults to the source selected in Startup Source. If no source is found, a 
blank screen displays. When Autosource is checked, Startup Source deter-
mines which source the projector defaults to at power-up. If no signal is 
present, the projector checks the sources in order until a source is found or 
until power down. 
Sources>RGB Video: check this box if you are using a DVD player with 
RGB output.
System>Rear: reverses the image so you can project from behind a translu-
cent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
Auto Power: When Auto Power is checked, the projector automatically 
goes into the startup state after the projector is powered on. This allows con-
trol of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching” or 
“Mute”) in the lower-left corner of the screen.
Low Power: (C420 only) toggles between on and off. Turn it on to lower the 
light output of the lamp. This also lowers the fan speed, making the projec-
tor quieter.
Pow e r  S av e: automatically turns the lamp off after no signals are detected 
for 5 minutes. After 3 additional minutes with no signal, the projector pow-
ers down. If an active signal is received before the projector powers down, 
the image will be displayed. 
Audio
SourcesStartup 
SourceSystem menu 
						

							34
Screen Save: automatically blanks the screen after no signals are detected 
for five minutes. The image returns when an active source is detected or a 
remote or keypad button is pressed. Screen Save is disabled when Power 
Save is enabled.
Screen Trigger : this enables the Screen Trigger connection on the connector 
panel. See page 6 for details.
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen at startup and when no source is detected. It 
also allows you to capture and display a custom startup screen. 
To capture a custom logo, display the image you want to capture on your 
computer, highlight Capture New, then press Select twice. While the cap-
ture is underway, the LED on the keypad turns orange. When ready, the 
projector confirms the capture and the LED changes to green. 
The next time you start the projector, the custom logo you captured dis-
plays.
Blank Screen: determines what color is displayed when you press the 
Blank button on the remote.
Startup LogoBlank Screen 
						

							35
Effect Key: allows you to assign a different function to the Effect button on 
the remote to quickly and easily use the effect. Only one effect can be 
enabled at a time. Highlight an effect and press Select to choose a different 
one. 
Blank: shows an empty screen. 
Mute: turns off all sound. 
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes computer sources to be reacquired.
Freeze: pauses the projected image.
Zoom: Is the default effect. It lets you magnify a part of the screen. To 
use the Zoom effect, press Effect, then press the remote’s left mouse to 
zoom the image, press the right mouse button to decrease the magnifi-
cation. You can use the cursor control to pan the image, displaying dif-
ferent parts of it (only if the image is magnified). To return to the 
original size and cancel Zoom, press the Effect button a second time.
About: displays the About menu.
PiP: (Picture in Picture) allows you to overlay a smaller window show-
ing the video source on top of the larger computer source window. You 
must have both a computer and video source connected to use PIP. You 
can’t show a computer image in the smaller PiP window, only a video 
image. You can select a small, medium, or large window. You can also 
move the PiP window on the screen using the PiP Position X and Y 
options in the menu. Press the up and down arrows to change the posi-
tion.
Mask: allows you to cover part of the image with a black curtain. Press 
the up and down arrows to raise or lower the curtain on the image.
Screen Trigger : this enables the Screen Trigger connection on the con-
nector panel. See page 6 for details.
Effect KeyPicture in Picture 
						

							36
Network: The projector has an RJ45 Ethernet connector that supports net-
work connections and TCP/IP protocols. This will allow for the control and 
management of the projector over a corporate network. The following fields 
are accessible when DHCP is not checked and available for manual entry of 
data.
IP Address: Identifies the projector on the network.
Subnet mask: Separates the network address part of the IP address.
Default gateway: The IP address of the local router.
DHCP: Select this to automatically obtain an IP address, Subnet mask, 
and Default gateway.
Network Info: Provides information on the network configuration.
The Network Info menu is informational and cannot be edited. It displays 
the current IP Address, Subnet Mask, Default Gateway, and the projector ’s 
MAC Address.
Language: allows you to select a language for the onscreen display of 
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours and Network set-
tings) to their default after displaying a confirmation dialog box.
Reset Lamp: resets the lamp hours counter in the About menu to zero. Do 
this only after changing the lamp. It displays a confirmation dialog box.
Service Info: provides information about the projector ’s software version 
and the active source.
Service Code: only used by authorized service personnel.
Network
Network
Info
Language
Service menu 
						

							37
MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
Changing the lensOptional long throw and short throw lenses are available. See “Optional 
Accessories” on page 41 for ordering information.1
Turn off the projector and unplug the power cable.
2
Set the projector upright with the lens facing upward, place a screw-
driver or other narrow object in the release hole on the bottom of the 
projector, then twist the lens counterclockwise to remove it.
3
To install the new lens, align the red dot (near the base of the lens) with 
the top of the projector and turn clockwise until you feel the lens click 
into place.
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner
computer 2
network
audio inLcomputer in
trigger
monitor out
serial control
R audio in
computer 1USBmouse
computer 3
I
O
turn off and unplug
the projector
lens release hole 
						

							38
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. When the specified end of the lamp’s life is reached, 
the message “Replace lamp” briefly appears on the screen at each startup 
and in the Interactive Display. You can order new lamp modules from your 
dealer. See “Accessories” on page 41 for information.1
Turn off the projector and unplug the power cable. 
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down and remove the lamp door by removing 
the two screws and sliding the lamp door tabs out of the two tab bays.
4
Loosen the three captive screws on the lamp module.
About
 menu
computer 2
network
audio inLcomputer in
trigger
monitor out
serial control
R audio in
computer 1USBmouse
computer 3
I
O
turn off and unplug
the projector
wait 60 minutesremove the screws on lamp door
loosen the screws on lamp module 
						

							39
WARNINGS: 
 To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.
 Do not drop the lamp module. The glass may shatter and cause injury.
 Do not touch the glass lamp screen. Fingerprints can obscure projection 
sharpness.
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing it.5
Carefully remove the lamp module by grasping and lifting the metal 
bail wire. Dispose of the lamp in an environmentally proper manner. 
6
Install the new lamp module, making sure that it is properly seated.
7
Tighten the three screws.
8
Replace the lamp door by inserting the tabs into the tab bays and tight-
ening the two screws.
9
Plug in the power cable, press the power switch then press the Pow e r 
button to turn the projector back on.
10
Reset the lamp hour timer.
Resetting the lamp timerAfter replacing the lamp, reset the lamp timer. Navigate to the Set-
tings>Service menu and select Lamp Reset to reset the lamp timer. 
remove module using bail wire
reset lamp time in Service menu