Projector LG Minibeam PW1500 User Manual

131EXTERNAL	CONTROL	DEVICE	SETUP
16. Tune Command (Command: m a)
* This command may work differently depending on model and signal.
 ►To tune channel to following physical/major/minor number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01][ ][Data02][ ][Data03][ ]
[Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel....

132EXTERNAL	CONTROL	DEVICE	SETUP
Data 05 : Input Source (Digital) -02 : Antenna TV (DTV) – Use Physical Channel Number -06 : Cable TV (CADTV) – Use Physical Channel Number -22 : Antenna TV (DTV) – Don’t Use Physical Channel Number -26 : Cable TV (CADTV) - Don’t Use Physical Channel Number -46 :  Cable TV (CADTV) – Use Major Channel Number Only  (One Part Channel)
Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0).
* Tune Command...

133EXTERNAL	CONTROL	DEVICE	SETUP
17. Channel Add/Del (Command: m b)
 ►To skip current channel for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data
00 : Del  01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del or add.
18. Key (Command: m c)
 ►To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data: To see "KEY CODES".
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
19. Energy Saving (Command: n p)
 ►Sets the energy saving mode.
Transmission...

134EXTERNAL	CONTROL	DEVICE	SETUP
20. Input select (Command: x b) (Main Picture Input)
 ►To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV  01 : CADTV
11 : CATV 10 : ATV
20 : AV 40 : Component
60 : RGB 90 : HDMI
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
21. 3D (Command: x t)
 ►To change 3D mode for Projector.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02]
Data Structure
[Data 00] 00 : 3D On
 01 :...

135EXTERNAL	CONTROL	DEVICE	SETUP
* All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.
[Data 00][Data 01][Data 02]
00OO
01XX
02XX
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02][x]
[t][ ][Set ID][ ][NG][Data00][x]
22. Extended 3D (Command: x v)
 ►To change 3D option for Projector.
Transmission [x][v][ ][Set ID][ ][Data 00][ ][Cr]
Data 00 : Right to Left  01 : Left to Right
Ack [v][ ][Set ID][ ][OK/NG][Data 00][x]
23. Auto Configure (Command: j...

136EXTERNAL	CONTROL	DEVICE	SETUP
Open	Source	Software	Notice	Information
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://\
opensource.lge.com.In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of...