Projector Christie Vivid Lx20 User Manual

							41
APPENDIX
Remote Control Unit
does not work.Check the batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Make sure the code of Remote Control is set to conform to projector.
(See “SETTING” section on page 35, 36.)
Problem:Try these Solution
Wireless Mouse
function does not
work.Check the cable connection between the projector and your computer.
Check the mouse setting on your computer.
Turn the projector on before turning on the computer.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community.  (EC)
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open the cabi-
net.
You can often correct operating problems yourself. If the projector fails to work properly, see the TROU-
BLESHOOTING section on pages 40 and 41.
If after following all operating instructions, you find that service is necessary, contact the Christie Service Station
or store where you purchased the unit. Give the model number and explain the difficulty. We will advise you on
how to obtain service. 
						

							42
APPENDIX
TECHNICAL SPECIFICATIONS
0.9 TFT Active Matrix type, 3 panels
Multi-media Projector
8.6 lbs (3.9 kg)
13.11 x 3.52 x 9.07 (333mm x 89.5mm x 230.5mm) (not including Adjustable Feet and Lens)
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 31” to 300”
800 TV lines
1 speaker, 1.18 x 1.57 (30mm x 40mm) 
41 F ~ 95 F (5 ˚C ~ 35 ˚C)
14 F ~ 140 F (-10 ˚C ~ 60 ˚C)
User’s Manual
AC Power Cord
Wireless Remote Control Transmitter and Batteries
VGA Cable
Control Cable for PS/2 port 
Carrying Bag
Lens Cover 
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Projection Image size (Diagonal)
Horizontal Resolution
Built-in Speakers
Operating Temperature
Storage Temperature
Accessories
LCD Panel System
The specifications are subject to change without notice.
F 1.7 ~ 2.0 lens with f 37.4 mm ~ 48.3 mm with motor zoom and focus
5.3’ ~ 40.0’ (1.6 m ~ 12.2 m)
200 W
RCA Type  x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
Projection Lens
Throw Distance
Projection Lamp
Video Input Jacks
RCA Type  x 2Audio Input Jacks
(VGA) HDB 15 Terminal x 1 and DVI 24 pin x 1
Mini Jack (stereo)  x 1
Mini DIN 8 pin x 1
RCA Type  x 2
1.0 W RMS
Computer Input Terminals
Computer Audio Input Jack
Control Port Connector
Audio Output Jacks
Internal Audio Amp
0˚ to 15.6˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class IILaser  
(Max. Output : 1mW / Wave length : 650±20nm)
Remote Control Transmitter
480i, 480p, 575i, 575p, 720p, 1035i, and 1080iHigh Definition TV Signal
USB Series B receptacle x 1USB Connector
AC 100 ~ 120 V (3.6 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (1.8 A  Max. Ampere), 50 / 60 Hz  (Continental Europe)
Voltage and 
Power Consumption
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give name and Type No. of it to the sales dealer.
Control Cable for Serial Port Type No. : 10-A POA-MCSRL
Control Cable for ADB Port Type No. : 10-A POA-MCMACMAC Adapter Type No. :10-A POA-MACAP 
						

							43
APPENDIX
CONFIGURATIONS OF THE TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG)
Terminal : HDB15-PIN 
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied).  When connecting the
Macintosh computer, MAC Adapter (not supplied) is required.
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable.
(Control Cable for PS/2 port is supplied, and Control Cables for Serial port and ADB port are not supplied.)
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin 
Connect the display output terminal of the computer to this terminal with a DVI cable (for Single Link T.M.D.S. / not supplied).  
1917
21018
31119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
Pin ConfigurationT.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).
2
341 
						

							Printed in Japan
Part No. 10-A 610 299 6029 (1AA6P1P3315-- MS6M)