Projector Christie Vista S3 User Manual

Section 3
Operation
Roadster/Vista User’s Manual3-1
This section explains how to use the projector once it has been installed. Please read
through these pages before using the projector for the first time. An understanding of
projector features and how to access them will help you to take full advantage of the
capabilities of the projector within minutes.
NOTE: Installation involves locating the projector and adjusting it for use at that
location. If you have not yet installed the projector, refer to...

OPERATION
3-2
Roadster/Vista User’s Manual
ZOOM  - Accessed manually in some models or with the keypad if a motorized zoom
lens is present, the lens barrel of a zoom lens (optional) rotates to adjust the size of
the image without moving the projector. Minimum and maximum image sizes
depend on which zoom lens is installed — see Section 5, Specifications.
FOCUS - Accessed manually in some models (via 2 “tabs” on the lens) or with a
keypad if a motorized lens is present, focus adjusts the sharpness of the...

OPERATION
Roadster/Vista User’s Manual3-3
COMPOSITE/S-VIDEO INPUT - Accepts a composite video and S-Video signal from
devices such as VCRs.
RGB INPUT - Accepts RGB and sync signals from devices such as computers, as well
as composite video, S-Video or YPbPr component signals.
RS-232 SERIAL INTERFACE (WITH LOOP THROUGH) - Allows one or more projectors to
be remotely controlled by a computer or controller, and provides a communications
connection for Christie’s Marquee Signal Switchers.
RS-422 SERIAL...

OPERATION
3-4
Roadster/Vista User’s Manual
light flashes green each time a key is pressed or when the projector receives a serial
command. Use the following as a guide:
Figure 3.2. Reading the Status LEDs
NOTE: A steady red power light accompanied by a coded pattern of red and yellow
flashes from the status light indicates an internal system error. Consult the rear LCD
display for an explanation, and see 3.11, Error Conditions. Should the problem
persist, contact a qualified service technician available...

OPERATION
Roadster/Vista User’s Manual3-5
While each keypad is identical in layout and provides complete control of the
projector, you may find one keypad more convenient than another for your specific
installation and application.
The built-in keypad is located at the rear of the projector. An LCD window above
this keypad provides feedback regarding current status and activities of the projector.
Figure 3.3. Keypad
The IR Remote Keypad controls the projector by way of wireless communications
from a...

OPERATION
3-6
Roadster/Vista User’s Manual
projector. One of two sensors on the projector will detect the signals and relay the
commands for internal processing.
The wired remote keypad connects to the 3-pin XLR jack via a 50 ft. cable. It is
recommended when:
• the rear of the projector is inaccessible
• the lighting conditions are unsuitable for proper IR transmission
• you want to use a separate keypad for each projector in a group
NOTES: 1) For extra long distances and/or harsh environments, you may...

OPERATION
Roadster/Vista User’s Manual3-7
Input 1
Press 
Input1 to select the source connected to INPUT 1 on the projector (data input).
This is the same as entering 
Input   .
Input 2
Press 
Input2 to select the source connected to INPUT 2 on the projector (an optional
interface). This is the same as entering 
Input   .
Input 3
Press 
Input3 to select the source connected to INPUT 3 on the projector (composite
video). This is the same as entering 
Input  .
Input 4
Press 
Input4 to select the source...

OPERATION
3-8
Roadster/Vista User’s Manual
Standby
Press 
Stby* and hold for approximately 1 second to blank all display and mute the
audio output (if connected) while keeping the projector in a warmed-up and ready
state. Or quickly press and release 
Stby* and follow immediately by ON or OFF if
you want to guarantee the correct toggle (useful if you are unsure of the present
status). Note that the lamp and electronics remain ON in standby mode, even though
the image turns to black and most functions are...

OPERATION
Roadster/Vista User’s Manual3-9
• Shutter* + ON = close the shutter (NOT PRESENT IN ALL MODELS)
Shutter* + OFF = open the shutter (NOT PRESENT IN ALL MODELS)
• Stby* + ON = put the projector in standby mode
Stby* + OFF = leave standby
• 
Powe r * +
 ON = turn the projector onPowe r * + OFF = turn the projector off
• 
Mute* + ON = turn the audio (if connected) and menu display on
Mute* + OFF = turn the audio (if connected) and menu display off
• 
OSD* + ON = turn the menu system on
OSD* + OFF =...