Projector Christie Roadster X9 User Manual

THROW DISTANCE
E-6
Roadster/Vista User’s Manual 

THROW DISTANCE
Roadster/Vista User’s ManualE-7 

THROW DISTANCE
E-8
Roadster/Vista User’s Manual 

Appendix F
Optional Input Modules
Roadster/Vista User’s ManualF-1
There are many optional input modules and accessories currently available for this projector. Contact your dealer for a
complete and up-to-date listing.
The Marquee Signal Switcher is a rack-mountable signal selector which can greatly
increase the number of analog sources (inputs) available to the projector. Connected
to 
INPUT 1, a single switcher provides up to 9 more sources to the projector.
Additional Marquee Signal Switchers can be...

OPTIONAL INPUT MODULES
F-2
Roadster/Vista User’s Manual
RGB500 Features
◊ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or
separate horizontal and vertical sync), up to 500 MHz bandwidth
◊ BNC connectors for RGB signal inputs
NOTE: The audio connectors are not functional. Connect audio to the projector’s 
IN
2
 audio port, if available (standard on Vista models only).
The RGB400 Buffered Amplifier Input Module may be installed in this projector, in a
Marquee Signal Switcher or in a...

OPTIONAL INPUT MODULES
Roadster/Vista User’s ManualF-3
The Composite/S-Video Input Module may be installed in this projector, a Marquee
Signal Switcher or a Marquee Case/Power Supply. The module receives either
composite video or S-video input signals from tape or disk players (do not connect
both types of signals simultaneously). Video inputs are 75
S  terminated. Video
outputs are provided for buffered loop-through to another display device.
Composite/S-video Features
◊ BNC connectors for composite RGB...

OPTIONAL INPUT MODULES
F-4
Roadster/Vista User’s Manual
The DVI Input Module can be installed in the projector at INPUT 2 to display digital
video input signals conforming to the DVI (Digital Visual Interface) single-channel
standard.
Features
◊ Supports Digital Visual Interface (DVI) single-channel
◊ Supports VESA Extended Display Identification Data (EDID)
◊ Provides an active-loop-through using a DVI connector (conforming to
the DVI Specification)
The Digital HDTV Input Module can be installed in...

OPTIONAL INPUT MODULES
Roadster/Vista User’s ManualF-5
The Serial Digital Input Module (SDI) can be installed in the projector at INPUT 2,
where it accepts a serial digital 4:2:2 component video signal (YCbCr) via a single
SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC out to
another device (such as another projector). Inputs are 75
S  terminated.
SDI Features
◊ accepts serial digital 4:2:2 component video (YCbCr)
◊ provides both a 
SERIAL IN and a SERIAL OUT BNC connector
◊...

Index
Roadster/Vista User’s ManualINDEX-1
A
AC Requirements, 2-1
Advanced 10-bit (ADP), 3-39
Noise and Filtering, 3-40
Anamorphic, 3-27
And Tiled Image, 3-54
Arrow Keys, 3-8
Aspect Ratio, 2-7, 3-25
Audio, 5-2
Input 1, 2-16
Input 2, 2-22
Input 3, 2-18
Input 4, 2-19
Auto Gain Control. See Enable Decoder AGC
Auto Input Level, 3-37
Auto Power Up, 3-43
Auto Setup, 3-24
AutoSource Checkbox, 3-23
B
Back IR Keypad, 3-45
Bad Sync, 3-55
Baud Rate, 2-31, 3-44
Blacklevels and Drives, 3-37
Blanking, 3-29
Brightness,...