Projector Christie Roadster X6 User Manual
Have a look at the manual Projector Christie Roadster X6 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 476 Christie manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Appendix F Optional Input Modules Roadster/Vista User’s ManualF-1 There are many optional input modules and accessories currently available for this projector. Contact your dealer for a complete and up-to-date listing. The Marquee Signal Switcher is a rack-mountable signal selector which can greatly increase the number of analog sources (inputs) available to the projector. Connected to INPUT 1, a single switcher provides up to 9 more sources to the projector. Additional Marquee Signal Switchers can be connected to the first, with their input locations (switcher#,slot#) selectable through the Input key on the keypad. Switcher inputs can also be selected at the switcher by pressing the appropriate front panel push-button, or through serial communications. See Section 2. Marquee Signal Switcher Features ◊ simple connection and push-button control ◊ easy to see, illuminated indicators ◊ 9 slots for analog interface modules ◊ RS-232 serial interface ◊ input for a wired remote keypad ◊ universal power input ◊ up to 9 switchers can be daisy-chained together with a projector The RGB500 Input Module may be installed in this projector, a Marquee Signal Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input signals from computers or other RGB source devices. Marquee Signal Switcher 38-801050-xx RGB500 Input Module 38-804606-xx
OPTIONAL INPUT MODULES F-2 Roadster/Vista User’s Manual RGB500 Features ◊ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate horizontal and vertical sync), up to 500 MHz bandwidth ◊ BNC connectors for RGB signal inputs NOTE: The audio connectors are not functional. Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only). The RGB400 Buffered Amplifier Input Module may be installed in this projector, in a Marquee Signal Switcher or in a Marquee Case/Power Supply. Connect three-, four-, or five-wire RGB video signals of up to 400 MHz bandwidth, signals typically produced by high-resolution computer or workstations. The buffering capability of the module enables the incoming signal to be sent to a remote destination. Inputs are 75 S terminated. RGB400BA Features ◊ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate horizontal and vertical sync) ◊ BNC connectors for RGB signal inputs ◊ Buffered signals to a remote destination NOTE: The audio connectors are not functional. Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only). The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input signals from computers or other RGB source devices. Video inputs are 75 S terminated. Video outputs provide buffered loop-through to another display device. RGB400ALT Features ◊ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or separate horizontal and vertical sync) ◊ BNC connectors for RGB signal inputs ◊ buffered loop-through video outputs NOTE: The audio connectors are not functional. Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only). RGB400BA Input Module 38-804610-xx RGB400 Active Loop-Thru Input Module 38-804607-xx
OPTIONAL INPUT MODULES Roadster/Vista User’s ManualF-3 The Composite/S-Video Input Module may be installed in this projector, a Marquee Signal Switcher or a Marquee Case/Power Supply. The module receives either composite video or S-video input signals from tape or disk players (do not connect both types of signals simultaneously). Video inputs are 75 S terminated. Video outputs are provided for buffered loop-through to another display device. Composite/S-video Features ◊ BNC connectors for composite RGB signals ◊ 4-pin mini-DIN connectors for S-Video signals ◊ buffered loop-through video outputs NOTES: 1) This interface is not a decoder. NTSC, PAL, or SECAM signals must connect to the video decoder installed at INPUT 3 / INPUT 4. 2) The audio connectors are not functional. Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only). 3) For use with this projector, do not connect both composite video and S-video signals to the Composite / S-Video Input Module– connect one or the other, even when plugged into a switcher. The PC250 Analog Input Module may be installed in this projector, a Marquee Signal Switcher or a Marquee Case/Power Supply. The module receives analog RGB input signals from IBM PC compatibles or Macintosh computers. Video inputs are 75 S terminated. Video outputs are provided for buffered loop-through to another display device. PC250 Analog Features ◊ accepts VGA or MAC RGB video ◊ 15 pin D connectors for video ◊ active loop-through video outputs NOTES: 1) This interface does not accept VGA and MAC signals simultaneously. 2) The audio connectors are not functional. Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only). 3) Trademarks are the rights of their respective owners. Composite / S-Video Input Module 38-804608-xx PC250 Analog Input Module 38-804609-xx
OPTIONAL INPUT MODULES F-4 Roadster/Vista User’s Manual The DVI Input Module can be installed in the projector at INPUT 2 to display digital video input signals conforming to the DVI (Digital Visual Interface) single-channel standard. Features ◊ Supports Digital Visual Interface (DVI) single-channel ◊ Supports VESA Extended Display Identification Data (EDID) ◊ Provides an active-loop-through using a DVI connector (conforming to the DVI Specification) The Digital HDTV Input Module can be installed in the projector at INPUT 2, where it accepts a digital 4:2:2 component HDTV signal (YCbCr) via a single SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC out to another device (such as another projector). Inputs are 75 S terminated. Features ◊ accepts a variety of digital HDTV 4:2:2 component signals (YCbCr), and de- serializes into a parallel 20-bit 4:2:2 component signal (10 bits each for Y and CbCr) ◊ SMPTE 292M compatible ◊ Two data rates: 1.485 Gb/sec or 1.485/1.001 Gb/sec. ◊ provides both a SERIAL IN and a SERIAL OUT BNC connector ◊ includes 4 status LEDs DVI Input Module 38-804635-xx Digital HDTV Input Module 38-804611-xx
OPTIONAL INPUT MODULES Roadster/Vista User’s ManualF-5 The Serial Digital Input Module (SDI) can be installed in the projector at INPUT 2, where it accepts a serial digital 4:2:2 component video signal (YCbCr) via a single SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC out to another device (such as another projector). Inputs are 75 S terminated. SDI Features ◊ accepts serial digital 4:2:2 component video (YCbCr) ◊ provides both a SERIAL IN and a SERIAL OUT BNC connector ◊ includes status LEDs for signal and error NOTE: Connect audio to the projector’s IN 2 audio port, if available (standard on Vista models only).. The Marquee Case/Power Supply enables you to use an analog input module as a stand-alone interface. Two supplies are available: one for use with 120 volt line voltage (38-801023-XX), and the other for use with 220 volt line voltage (38-801026-XX). Both models include a 15 VDC, 500 mA AC adapter. Marquee Case/Power Supply Features ◊ easy installation — no tools required ◊ the Marquee Case/Power Supply accepts the following input modules for use with this projector: RBG500, RGB400 Active Loop-Thru, RGB400 Buffered Amplifier, Composite/S-Video, and PC Analog. Digital inputs cannot be used. ◊ retaining clip to secure AC adapter ◊ non-slip feet ◊ supplied with 110 or 220 volt AC adapter Serial Digital Input Module 38-804602-xx Marquee Case/Power Supply 38-801023-xx 38-801026-xx
Index Roadster/Vista User’s ManualINDEX-1 A AC Requirements, 2-1 Advanced 10-bit (ADP), 3-39 Noise and Filtering, 3-40 Anamorphic, 3-27 And Tiled Image, 3-54 Arrow Keys, 3-8 Aspect Ratio, 2-7, 3-25 Audio, 5-2 Input 1, 2-16 Input 2, 2-22 Input 3, 2-18 Input 4, 2-19 Auto Gain Control. See Enable Decoder AGC Auto Input Level, 3-37 Auto Power Up, 3-43 Auto Setup, 3-24 AutoSource Checkbox, 3-23 B Back IR Keypad, 3-45 Bad Sync, 3-55 Baud Rate, 2-31, 3-44 Blacklevels and Drives, 3-37 Blanking, 3-29 Brightness, 3-31, 5-1 Brightness Key, 3-9, 3-31 Broadcast Key, 3-46 Broadcasting, 3-10, 3-52 C Calibrate Lens, 3-11 Ceiling Mounting, 2-14 Center Lens, 3-12 Channel Locked, 3-23 Name, 3-23 Number, 3-20, 3-23 Channel Copy/Delete, 3-21 Channel Edit Menu, 3-22 Channel Key, 3-7, 3-19 Channel Selection, 3-20 Channel Setup Menu, 3-20 And Enter Key, 3-21And Function Key, 3-21 Channels Creating automatically, 3-19 Creating in Channel Setup Menu, 3-21, 3-22 Definition of, 3-19 Deleting in Channel Setup Menu, 3-22 Maximum Number, 3-18 Checkbox Toggles, 3-16 Clamp Tip, 3-38 Color (Adj.), 3-32 Color and Uniformity Menu, 3-42 Color Enable, 3-34, 3-38 Color Key, 3-9 Color Setup Menu, 3-32 Color Space, 3-31 Color Temperature, 5-1 How to Copy, 3-34 Interpolated, 3-34 Modifying a Setup, 3-34 Presets and Factory Presets, 3-35 User, 3-34 Color Temperature Setup, 3-33 Communications Menu, 3-42, 3-44 Component Video, 2-17 Components, 1-2 Location and Use, 3-1 Composite Video Connecting, 2-18 Extra, 2-22 Loop-Through, 2-20 Configuration Menu, 3-41 Contrast, 3-30 Contrast Key, 3-9, 3-30 Contrast Ratio, 5-1 Custom Sizing, 3-26 D Dark Interval, 3-40 Decoder Luma Delay, 3-36 Detail, 3-31 Detail Key, 3-9, 3-31 Diagnostics and Calibration, 3-43 Display Channel List, 3-41 Display Error Messages, 3-42 Display Slidebars, 3-42 DVI / DFP Input Module, 3-30