Projector Christie Mirage S2k User Manual

Section 2: Installation and Setup 
 
  
 User’s Manual     2-15. 
As an alternative to the projector’s keypad or remote, you may wish to communicate 
with the projector using a PC or other controller. Such a device sends commands and 
receives feedback via serial links (RS232 and RS422), Ethernet or GPIO 
communications to the projector, all described below. 
As desired, direct the projector’s IR remote keypad towards the display screen or the 
projector’s IR sensors. Alternatively, connect a wired...

Section 2: Installation and Setup 
2-16   
  User’s Manual      
 
Figure 2.12. Connecting RS422 
 
Ethernet Communications 
To add the projector to an existing Ethernet network with other equipment such as 
controllers and other projectors, connect standard CAT5 Ethernet cable between your 
Ethernet controller (or hub) and the Ethernet port on the side of the projector. 
Upon connection to an Ethernet network, the projector’s factory default IP address of 
0.0.0.0.0 will automatically enable the DHCP...

Section 2: Installation and Setup 
 
  
 User’s Manual     2-17. 
 
Figure 2.13. 
MIXED NETWORK: To control multiple projectors with a computer/controller having an 
RS422 interface, first set them all to the same baud rate as your RS422 controller. 
NOTE: You must enable this combination of RS422 and RS232 in the 
Communications menu. Set the “Network Routing” option to “RS232 and RS422 
Joined”. See Section 3 for details. 
Then chain the projectors together by connecting an 
RS232 port of the first...

Section 2: Installation and Setup 
2-18   
  User’s Manual      
ETHERNET NETWORK SETUP: To add one or more projectors to an Ethernet network, 
use standard CAT5 cable to connect each projector’s Ethernet port to a hub belonging 
to the network. A controller or PC must also be connected to the hub. See Figure 2.15. 
 
Figure 2.15. 
SETTING THE PROJECTOR’S IP ADDRESS: Upon connection to most Ethernet 
networks, each projector’s factory default IP address of 0.0.0.0 triggers the network’s 
DHCP (Dynamic...

Section 2: Installation and Setup 
 
  
 User’s Manual     2-19. 
By default, communications originating from one type of serial controller—RS232 vs. 
RS422 vs. Ethernet—stay on the corresponding network path. This separation is 
indicated by a “Separate” setting for “Network Routing” in the Communications 
menu. If you are using an RS422 controller, for example, it will communicate only 
with the projector to which it is connected unless you change this setting to either 
“RS232 and RS422 Joined” or...

Section 2: Installation and Setup 
2-20   
  User’s Manual      
Always power down the projector before unplugging the AC line cord. Wait 5-10 
minutes for the main exhaust fan to turn off and for the lamp to cool sufficiently 
before unplugging the projector.  
 WARNINGS 
Do not attempt operation if the AC supply and cord are 
not within the specified voltage and power range. 
Wait for the cooling fans to turn off before unplugging the 
projector. 
 
 
  

Section 3 
Operation  
 
 User’s Manual     3-1 
 
This section explains how to effectively operate the projector once it has been 
installed. It is recommended that you read this section and familiarize yourself with 
the components and the available menu options before you begin using your projector 
for the first time. 
 
 
Figure 3.1. Projector Basics 
  
The built-in keypad is located at the back of the projector, beside the input panel. Use 
it similarly to the IR remote to control the projector. A...

Section 3: Operation 
3-2   
  User’s Manual      
The projector is built with a motorized lens mount that allows for easy lens control 
and adjustment. This includes such functions as adjusting vertical and horizontal 
offsets, zoom and focus. The lens mount can be fitted with any one of the available 
optional lenses – see Section 6 - Specifications.  
• Zoom and Focus – There are two internal lens motors that allow for quick 
motorized adjustment of zoom and focus. Adjust zoom to fit the displayed...

Section 3: Operation 
 
  
 User’s Manual     3-3. 
 
 
 Laser radiation is emitted from the laser diode in the remote. Do not look 
directly into the beam of the remote.
 
 
The projector is typically controlled using one of the following keypads: 
• Built-in Keypad located at the back of the projector  
• Remote Keypad for tethered or tetherless control up to 100 feet away 
(includes cable for use as a wired remote) 
While each of the keypads provides complete control of the projector, they differ...

Section 3: Operation 
3-4   
  User’s Manual      
 
 
 
* These are toggle keys, which require you to press and hold or press twice or 
press and use the up/down arrow keys. NOTE: To turn the OSD off you must 
press 
OSD and . 
Figure 3.3. Remote Keypad