Projectiondesign Projector F35 User Manual

31
5.15 Configuring 3D (AS3D)
This is information is only applicable to the WUXGA and 1080p versions, \
not WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To 
enable active stereo select 3D > 3D MODE. Enabling 3D mode will configure the projector for 
the use with an active stereo source.
The only active stereo 3D format natively supported by the projector is sequential left/
right at a frequency between 100 and 120 Hz. Both DVI and HDMI connectors can be...

32User’s Guide - Basic setupF35/FL35  
user’s guide - Basic setup
1920 x 1080 (1080)
5.16 Image sizes
Lens types and specifications may change without prior notice.  
For correct lens information please refer to projectiondesign.com/products/lenses
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Screen diagonalm
15.00
13.75
12.50...

33
1920 x 1200 (WUXGA)
Projec tion distanc e
Image widthOfset (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Scr een diagonalm
15.00
13.75
12.50
11.25
10.00
8,75
7.50
6.25
5.00
3.75
2.50
1.25 0
Ultra  Wide Angle (EN12)  0.79 : 1 (0.5 - 2.5m)
Wide Angle Z oom (EN13) 1.24 - 1.60 : 1 (1.0 - 15m)
Wide Angle  (EN15) 1.16 :  1  (1.0 - 15m)
Standard Zoom (EN11) 1.60 - 2.32 : 1...

34User’s Guide - Basic setupF35/FL35  
user’s guide - Basic setup
2560 x 1600 (WQXGA)  / 2560 x 1080 (panorama)
Wide Angle (EN42) 0.80 : 1 (0.7 -  7m)
Ultra  Wide Angle (EN45)   0.80 - 1.21 : 1  (5 - 30m)
Wi de Angle Z oom (EN43) 1.20  - 1.69 : 1 (1.5 - 15m)
Standard Zoom (EN41) 1.69 - 2.50 : 1 (1.5  - 15m)
Short  Zoom  (EN44) 2.50 - 4.61 : 1 (2.0 – 40 m)
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12...

35
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When 
several projectors are in use in an installation, individual control may be convenient. Individual 
control is available either by wired remote control, using the data-jack, or by using an individ-
ual number code. For individual control, first set the individual RC ID code using the projector 
menu system, see the SETTINGS sub...

36User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, 
the projector is supporting a dual head input mode. In this mode the left and \
right half of the 
image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively  
(Figure 6-1).  
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is 
the only available option at...

37
6.4 Multi-channel 3D synchronization
X-PORT DCC120 has advanced capabilities for handling synchronization of multiple projec-
tors in a 3D installation.
6.4.1 Synchronous frame sequential
A typical synchronous frame sequential 3D setup is shown in Figure 6-2.
 
Figure 6-2. Synchronous frame sequential 3D
In this case IGs are synchronized and 3D sync from the source is connected from the DIN 
connector on the IG to the BNC sync-in connector. The source 3D sync is then sent to every 
projector in the...

38User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.4.3 Synchronous side-by-side
Figure 6-3 illustrates a typical synchronous side-by-side 3D setup.
 
Figure 6-3. Synchronous side-by-side setup
Since the sources are synchronized in this setup, synchronization management is not re-
quired in the projector. The table below shows the recommended system settings.
SETTINGPROJECTOR 1PROJECTOR 2
3DSide-by-sideSide-by-side
3D L/R syncSourceSource
3D BNC sync-out signalNot used, but can be...

39
6.4.4 Asynchronous side-by-side
In asynchronous side-by-side 3D, the projectors utilize the BNC sync-in and sync-out con-
nectors to distribute a system wide display sync. This display sync is u\
sed by all projectors 
to perform frame rate conversion on the input signals if necessary. Figure 6-4 illustrates this 
setup.
Figure 6-4. Asynchronous side-by-side setup
As seen in Figure 6-4, an extra cable is connected between BNC sync-out on projector 1 
and BNC sync-in on projector 2. In this setup the...

40User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.5 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based 
on information from the source.
To manually override the automatically detected color space and digital l\
evel go to menu 
entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and selec\
t 
your color space and digital drive level.
6.6 Disabling IR receivers
The...