Projectiondesign F35 As3d Projector User Manual

english
21
www.projectiondesign.com
5.3 Lamp operation
The projector is fitted with two individual projection lamps that can be run in various modes. 
In addition, lamps can be replaced as needed separately. This ensures an optimized cost of 
ownership. Individual lamp timers are maintained for each lamp.
Lamp operation mode is controlled in the INSTALLATION > LAMPS sub menu.
5.4 Ceiling mount
The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount 
fixture, with a capacity...

english
22User’s Guide - Basic setup
A
B                          
C
F35 User’s Guide - Basic setup
5.4.1 Ceiling mount cover
The supplied auxiliary cable cover can be mounted on the projector to conceal the interface 
cables and power cord when the unit is ceiling mounted. Connect all cables and fix them in\
 
place before the cable cover is attached to the projector. Figure 5-3 shows the ceiling mount 
cover.
Figure 5-3. The ceiling mount cover
5.4.2 Attaching the ceiling cover
To attach the ceiling...

english
23
www.projectiondesign.com
5.5 Connection and cables
NOTE! Before setting up, switch off all equipment and disconnect the power co\
rd.
In order to prevent damage to the projector caused by overvoltages (e.g. lightning), we rec-
ommend connection to a line (mains) circuit which has overvoltage protection when installing.
5.5.1  Setting up a video source
For best quality video, connect a digital video source using the HDMI 1.3a interface (A) in Fig-
ure 5-4. Both HDMI inputs are HDCP copy...

english
24User’s Guide - Basic setupF35 User’s Guide - Basic setup
5.6 Image alignment
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the vari-
ous test images using the arrow keys. When a test image matching the aspect ratio of your 
screen has been found, use the zoom, focus, lens shift and physical projector alignment to 
match the screen.
5.7 Setting image orientation
In relation to the screen,...

english
25
www.projectiondesign.com
5.11 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier 
use all over the world. The default language is English.
The available languages are:
•	English
•	French
•	German
•	Spanish
•	Russian
•	Norwegian
•	Swedish
•	Korean
•	Japanese
•	 Chinese	Simplified
•	 Chinese	Traditional
•	 Portuguese
•	 Italian
To change the language of the menu system, just select “LANGUAGE” f\
rom the top menu 
and...

english
26User’s Guide - Basic setupF35 User’s Guide - Basic setup
5.13 Configuring Active Stereo 3D (AS3D)
NOTE! This is information is only applicable to the WUXGA and 1080p versions,\
 not 
WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To 
enable active stereo select STEREO > STEREO MODE. Enabling stereo mode will configure 
the projector for the use with an active stereo source.
NOTE! The only active stereo 3D format natively supported by the projector...

english
27
www.projectiondesign.com
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When 
several projectors are in use in an installation, individual control may be convenient. Individual 
control is available either by wired remote control, using the data-jack, or by using an individ-
ual number code. For individual control, first set the individual RC ID code using the projector...

english
28User’s Guide - Advanced setupF35 User’s Guide - Advanced setup
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, 
the projector is supporting a dual head input mode. In this mode the left and \
right half of the 
image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively  
(Figure 6-1).  
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is 
the only available option at...

english
29
www.projectiondesign.com
6.6 Controlling screens with triggers
The projector has to programmable triggers with 3.5 mm2 mini-jack connectors. These can 
be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
•	Trigger 1 is set to control a screen depending on whether projector is powered on or not.
•	Trigger 2 is set to control a screen depending on the aspect ratio of currently active...

english
30User’s Guide - Advanced setupF35 User’s Guide - Advanced setup
6.9 Disabling LED indicators
In certain installations it may desirable to completely disable the LED \
indicator in the keypad 
of the projector. To disable the LED indicators, go to menu entry SETTINGS > LED  
INDICATORS MUTE.
If the LED indicators are enabled, the timeout period can be set in the menu under SET-
TINGS > BACKLIGHT TIMEOUT.
6.10 Setting the background color
The background color displayed when the projector is...