Projectiondesign F35 1080p Projector User Manual

							31
5.15 Configuring 3D (AS3D)
This is information is only applicable to the WUXGA and 1080p versions, \
not WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To 
enable active stereo select 3D > 3D MODE. Enabling 3D mode will configure the projector for 
the use with an active stereo source.
The only active stereo 3D format natively supported by the projector is sequential left/
right at a frequency between 100 and 120 Hz. Both DVI and HDMI connectors can be 
used for sources up to 165 Mhz. For sources between 165 and 330 Mhz, only DVI dual 
link is supported.
After enabling stereo mode, configure the glass type being used by selecting 3D > 3D 
GLASSES TYPE. The follow glasses are support:
• DLP Link™
• IR
• IR high brightness (may cause crosstalk)
When using IR glasses it is important to configure the phase delay between the glasses 
and actual image. This is done using 3D > 3D LOCK PHASE DELAY with values 0 and 179 
degrees.
If left/right data channels are swapped there will be no 3D effect in the image, only parallel 
distortion between the channels. This can be countered by enabling the 3D > SWAP EYES 
feature.
User selectable Brilliant Color™ processing will be disable when 3D is enabled.
english  
www.projectiondesign.com  
						

							32User’s Guide - Basic setupF35/FL35  
user’s guide - Basic setup
1920 x 1080 (1080)
5.16 Image sizes
Lens types and specifications may change without prior notice.  
For correct lens information please refer to projectiondesign.com/products/lenses
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Screen diagonalm
15.00
13.75
12.50
11.25
10.00
8,75
7.50
6.25
5.00
3.75
2.50
1.25 0
Ultra  Wide Angle (EN12)   0.79 : 1 (0.5 - 2.5m)
Wide Angle Zoom (EN13) 1.24 - 1.60 : 1 (1.0 - 15m)
Wide Angle (EN15) 1.16  : 1 (1.0 - 15m)
Standard Zoom  (EN11) 1.60 - 2.32 : 1 (2.0 - 15m)
Tele Z oom (EN14) 2.37 - 3.79 : 1 (2.0 - 30m)
Long Tele Z oom (EN16) 3.80 - 6.50 : 1 (4.0 –  40 m)
english    
						

							33
1920 x 1200 (WUXGA)
Projec tion distanc e
Image widthOfset (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Scr een diagonalm
15.00
13.75
12.50
11.25
10.00
8,75
7.50
6.25
5.00
3.75
2.50
1.25 0
Ultra  Wide Angle (EN12)  0.79 : 1 (0.5 - 2.5m)
Wide Angle Z oom (EN13) 1.24 - 1.60 : 1 (1.0 - 15m)
Wide Angle  (EN15) 1.16 :  1  (1.0 - 15m)
Standard Zoom (EN11) 1.60 - 2.32 : 1 (2.0 - 15m)
Tele Zoom (EN14) 2.37 - 3.79 : 1 (2.0 - 30m)
Long Tele Z oom (EN16) 3.80 - 6.50 : 1 (4.0 – 40 m )
0.00 0.50 1.00 1.50 2.00 2.50
3.00 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50
3.5025
0
10 20
english  
www.projectiondesign.com  
						

							34User’s Guide - Basic setupF35/FL35  
user’s guide - Basic setup
2560 x 1600 (WQXGA)  / 2560 x 1080 (panorama)
Wide Angle (EN42) 0.80 : 1 (0.7 -  7m)
Ultra  Wide Angle (EN45)   0.80 - 1.21 : 1  (5 - 30m)
Wi de Angle Z oom (EN43) 1.20  - 1.69 : 1 (1.5 - 15m)
Standard Zoom (EN41) 1.69 - 2.50 : 1 (1.5  - 15m)
Short  Zoom  (EN44) 2.50 - 4.61 : 1 (2.0 – 40 m)
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Scr een diagonalm
15.00
13.75
12.50
11.25
10.00
8,75
7.50
6.25
5.00
3.75
2.50
1.25 0
0.00 0.50 1.00 1.50 2.00 2.50
3.00 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50
3.50 25
0
10 20
english    
						

							35
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When 
several projectors are in use in an installation, individual control may be convenient. Individual 
control is available either by wired remote control, using the data-jack, or by using an individ-
ual number code. For individual control, first set the individual RC ID code using the projector 
menu system, see the SETTINGS sub menu. Then, to select a specific projector to control, 
first press the ‘*’ button in the lower keypad area, then the code as set in the target projector. 
A code can be in the range ‘0’..’99’. ‘0’ is reserved for broadcast. To select another target, 
repeat the process by pressing ‘*’ and a new code. To exit individual control, press ‘*’’*’ twice 
or press ‘*’ and ‘0’.
6.2 Protecting the projector with a pin code
The projector may be controlled by a PIN (Personal Identification Number) code. The PIN 
code is 4 digits, and if the PIN code is activated, you must enter the c\
orrect code to unlock 
the projector. Factory set PIN (1234).
To activate, deactivate or change the PIN code, see the SETTINGS > PIN CO\
DE sub menu.
If an incorrect PIN code is entered, you may try again two times.  
If you fail three times in a row, a PUK (unlock) code is needed.  
The PUK code is supplied with the product.
Entering the puk code correctly is the customers responsibility
 
If you also fail three times with the PUK code, the projector locks up permanently, and can 
only be unlocked by a special service unlock code. 
To access this code, you will need to contact your dealer or a service st\
ation. The service 
unlock code will be generated based on a secure, encrypted number that is produced by the 
projector itself. The projector will produce a new number every time.
To unlock the projector, proof of ownership must be provided by the customer
english  
www.projectiondesign.com  
						

							36User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, 
the projector is supporting a dual head input mode. In this mode the left and \
right half of the 
image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively  
(Figure 6-1).  
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is 
the only available option at this time.
Figure 6-1. Dual input mode
An example of this is feeding a WUXGA (1920 x1200) 120Hz source with 960 x 1200 - 
120Hz source resolutions on each the DVI interfaces. 
When enabling this mode, the EDID data on each of the DVI connectors wil\
l automatically be 
changed from WUXGA (1920 x 1200) 120Hz to 960 x 1200 - 120Hz.
For the image to be displayed in this mode, the resolution must be exactly the same 
on both connectors.
In this mode the two connected sources must have exactly the same timing. A drift in 
timing between the inputs will result in a visible split in the center of image.
Some graphic cards have problems with detecting the change from single head to 
dual head mode. If problems occur, disconnect both signal cables before enabling or 
disabling the dual mode in the menu.
12
english    
						

							37
6.4 Multi-channel 3D synchronization
X-PORT DCC120 has advanced capabilities for handling synchronization of multiple projec-
tors in a 3D installation.
6.4.1 Synchronous frame sequential
A typical synchronous frame sequential 3D setup is shown in Figure 6-2.
 
Figure 6-2. Synchronous frame sequential 3D
In this case IGs are synchronized and 3D sync from the source is connected from the DIN 
connector on the IG to the BNC sync-in connector. The source 3D sync is then sent to every 
projector in the setup. See table below.
SETTINGPROJECTOR 1PROJECTOR 2
3DFrame sequentialFrame sequential
3D L/R syncBNC sync-inBNC sync-in
3D BNC sync-out signalPass throughPass through
6.4.2 Asynchronous frame sequential
This mode is not supported.
english  
www.projectiondesign.com  
						

							38User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.4.3 Synchronous side-by-side
Figure 6-3 illustrates a typical synchronous side-by-side 3D setup.
 
Figure 6-3. Synchronous side-by-side setup
Since the sources are synchronized in this setup, synchronization management is not re-
quired in the projector. The table below shows the recommended system settings.
SETTINGPROJECTOR 1PROJECTOR 2
3DSide-by-sideSide-by-side
3D L/R syncSourceSource
3D BNC sync-out signalNot used, but can be set to 3D glass sync.Not used, but can be set to 3D glass sync.
english    
						

							39
6.4.4 Asynchronous side-by-side
In asynchronous side-by-side 3D, the projectors utilize the BNC sync-in and sync-out con-
nectors to distribute a system wide display sync. This display sync is u\
sed by all projectors 
to perform frame rate conversion on the input signals if necessary. Figure 6-4 illustrates this 
setup.
Figure 6-4. Asynchronous side-by-side setup
As seen in Figure 6-4, an extra cable is connected between BNC sync-out on projector 1 
and BNC sync-in on projector 2. In this setup the projectors need the settings in the table 
below to send/utilize the display sync correctly.
SETTINGPROJECTOR 1PROJECTOR 2
3DSide-by-sideSide-by-side
3D L/R syncSourceBNC sync-in
3D BNC sync-out signal3D display L/R syncPass through
english  
www.projectiondesign.com  
						

							40User’s Guide - Advanced setupF35/FL35  
user’s guide - Advanced setup
6.5 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based 
on information from the source.
To manually override the automatically detected color space and digital l\
evel go to menu 
entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and selec\
t 
your color space and digital drive level.
6.6 Disabling IR receivers
The projector has 3 IR receivers as shown in chapter “4.1 Overview”.
These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION > 
IR FRONT / IR REAR to disable the receivers.
6.7 Controlling screens with triggers
The projector has two programmable triggers with 3.5 mm mini-jack connectors. These can 
be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
• Trigger 1 is set to control a screen depending on whether projector is powered on or not.
• Trigger 2 is set to control a screen depending on the aspect ratio of currently active 
source.
Both triggers can be manually overridden both in the menu system and by \
using the com-
mand and control protocol through RS-232 or LAN.
6.8 Setting aspect trigger behavior
To customize the aspect trigger functionality, go to menu entry INSTALLATION > TRIGGER > 
ASPECT TRIGGER BEHAVIOR. In this sub-menu it is selectable for which input aspect ratios 
the trigger will be enabled.
6.9 Automatic power on/off
The projector can be automatically powered on or off by using the internal timer function or 
DPMS.
6.9.1  Using the timer
The projector features a real-time clock that enables timing control. This means that the 
projector can be programmed to switch on and off at certain pre-set times during a weekly 
cycle.
To allow for a flexible schedule, 10 ‘programs’ are available. With each program, you can 
define the switch on or switch off time for a single day (Monday to Sunday), all work days 
(Monday through Friday), or week-end (Saturday and Sunday). One, several or all programs 
can be active at the same time as desired. In this way, a flexible scheme can be established. 
Observe the 24 hour time format. For more information, see the SETTINGS > TIMER menu.
The following example illustrates a case where the projector turns on at 08:00 in the morning 
(8 am) and switches off at 20:00 (8 pm) on weekdays (Monday through Friday). Weekends 
(Saturdays and Sundays), it turns on at 10:00 (10 am) and off at 18:00 (6 pm). VGA is used 
as the source. For this, four programs are needed, 2 for on and two for off.
english