Polaroid Projector Polaview 330 User Manual

 
English 7 
Getting Started 
2 Connect the yellow video plug to the Composite Video In connector on 
the projector and to the video output connector on the video player. 
Figure 8: Connecting to Composite Video/Audio 
To connect to S-video:
1  Connect the audio plugs on the audio/video cable to the left and right 
audio connectors on the projector and to the audio output connectors 
on the video player.
2 Connect the S-video plug to the S-Video connector on the projector 
and to the video output...

 
8 English 
Getting Started 
3 Connect the remote mouse interface cable to the Mouse connector on 
the projector and to the mouse connector (serial, PS/2, ADB) on your 
computer. 
Figure 10: Connecting to the Remote Mouse
Mouse
connector 

 
English 9 
Operating the Projector 
Operating the Projector 
This section explains how to turn on the projector and adjust the 
projected image. 
Turning On the 
Projector 
Use the Power On/Standby button to turn on the projector.
To turn on the projector:
1  Check that the projector is connected to AC power and the projector is 
in the  
sleep state 
 as described on page 14.
2 Press the Power On/Standby button on the projector keypad. 
Figure 11: Power On/Standby Button 
The projector enters the...

 
10 English 
Operating the Projector 
For more information on the projectorÕs operating states, see ÒOperating 
StatesÓ on page 14. 
Tip: 
If the projector is connected to a laptop computer but is not project-
ing an image, make sure that you have activated the external video
output port correctly. For more information, see ÒActivating the
Laptop External Video PortÓ on page 32. 
Focusing the 
Image 
Use the Focus Ring to focus the projected image.
To focus the image:
¥ Rotate the Focus Ring until the...

 
English 11 
Operating the Projector 
Distance to 
Screen vs. Image 
Size 
Use the following chart and tables to determine the distance between the 
projector and the screen for a desired screen image size.
The top line in the graph indicates the image size with the lens at the 
maximum zoom position. The bottom line in the graph indicates the 
image size with the lens at the minimum zoom position. 
Figure 14: Distance to Screen vs. Image Size 
The following table contains information about image size...

 
12 English 
Operating the Projector 
The following table contains information about image size with the zoom 
lens at the maximum zoom position. 
Table 2: Distance to Screen vs. Image Size, Lens at Maximum Zoom 
Adjusting the 
Image Height 
Use the quick-release Elevator Foot Release under the front of the 
projector to adjust the height of the projected image.
To adjust the image height:
1  Press the Elevator Foot Release and lift the front of the projector.
2 Release the Elevator Foot Release to lock...

 
English 13 
Operating the Projector 
Leveling the 
Image 
Use the leveling feet, located on both rear corners of the projector, to level 
the projected image.
To level the image:
¥ Rotate one or both leveling feet until the projected image is level.  
Figure 16: Leveling the Image
Leveling Foot 

 
14 English 
Operating States 
Operating States 
The Polaview 330 LCD projector has Þve operating states:
1  
Sleep state 
 - The lamp, all fans, and keypad lighting are off. The 
Power On/Standby LED, Lamp Age LED, and Lamp Status LED are 
on.
2 
Live state 
 - The lamp and keypad lighting are on. The fans are on at 
high speed. The projector displays either the source video or the logo.
3 
Standby state 
 - If the lamp has been on for more than 30 seconds, 
pressing the Power On/Standby button causes...

 
English 15 
Using the Remote Control 
Using the Remote Control 
This section explains how to use the remote control.
The wireless remote control that comes with the Polaview 330 LCD 
projector is similar to a remote control for a television or VCR. Use the 
remote control to set up and adjust the image settings and to control 
interactive presentations. 
Figure 17: Remote Control 
Use the projector control buttons on the remote control to control 
projector functions. Use the built-in joystick and the...

 
16 English 
Using the Remote Control 
Source 
Press the Source button on either the remote control or the projector 
keypad to toggle the input signal source between computer, composite 
video, and S-video. If there are no other active input signal sources 
connected, the projector displays an error message. 
Menu 
Press the Menu button on either the remote control or the projector 
keypad to display the on-screen main menu. Press the Menu button again 
to exit the menu. 
Direction Keys 
Use the...