Polaroid Projector Polaview 220 User Manual
Have a look at the manual Polaroid Projector Polaview 220 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 15 Polaroid manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
True-to-life color Examine the projected image for true-to-life color rendition. renditionUse the TINT option to make the adjustments: 1From the projector control panel or remote control, press the IMAGE menu key. 2Using the cursor pad, scroll through the menu selections and highlight TINT on the on-screen menu display. 3Use the left () arrow keys on the cursor pad to adjust the color balance of the projected image. Restoring factory If desired, you can restore the original factory settings by settingsselecting the SETUP menu key, using cursor pad to select the RESET option, and depressing the right arrow key. Any changes from the default setting are stored in memory for that source. Note:If for any reason the projector should not respond to the control panel or remote control commands, you can reset it by performing the following steps: 1Turn off the unit and allow it to cool for at least 3 minutes. 2Press the SET UP key on the projector control panel and turn on the projector as you continue pressing the SET UP key. Continue to press the SET UP key until the LEDs of the SOURCE 1–4 keys on the control panel light up red and green. 3Release the SET UP key. 4Reconfigure the projection settings for rear projectors, ceil- ing mount, as required. 28Using the projector
Storage, cleaning and care Store the Polaview Model 220 Projector either in its original shipping container or carrying case to guard it against dust and lint. Use a non-abrasive, lint-free cloth and non-abrasive cleaning solution, such as an eyeglass or camera-lens clean- ing solution, on the lens to keep it clean. Spray the cleaning solution directly on the cleaning cloth, never on the lens. Warning:Always disconnect your projector from its electri- cal supply before performing any maintenance on it. Extreme temperaturesDo not expose the projector to temperatures less than -13°F (-25°C) or greater than 140°F (60°C). For example, avoid storing it in parked automobiles for an extended period of time. Do not operate the projector in temperatures less than 32°F (0°C) or greater than 95°F (35°C). 4 Maintenance
Replacing the lamp assembly When you notice that the output from the projector lamp starts to weaken, you need to replace the lamp assembly (part number 623374). Caution:Replace the lamp assembly at the first sign of the bulb weakening. Do not wait for bulb to burn out as it is possible for the failing bulb to burst. 1Turn off the projector. 2Unplug the projector power cord from the wall socket and from the power receptacle. Remove the lamp-Depress the latch on the top center edge of the door and assembly doorpull the top edge of the door toward you. Refer to the illustration below. The lamp assembly and lamp-assembly door 30Maintenance Door latch Locking key Handle D LP
Remove theUnlock the lamp assembly by rotating the locking key on lamp assembly the right side of the lamp assembly counter-clockwise one- half revolution. Grasp the wire handle and gently pull the lamp assembly straight out of the unit. Replace the Align the lamp-assembly slide rails with the slide-rail lamp assemblychannels inside the projector and gently slide the lamp assembly into the projector. When the lamp assembly is properly in seated in the projector, rotate the locking key clockwise one-half revolution. Note:Take care not to touch the lamp in the new assembly. The smallest oil deposit from your finger can significantly shorten the life of the lamp. Replace theAlign the tabs on the bottom of the door with the slots lamp-assembly doorin the door opening. Gently push the top of the door into place until the latch snaps into position. Turn the projector on to verify that the lamp functions properly. Note:The removal of the lamp-assembly door activates a safety switch that disconnects electrical power from the lamp assembly. Improper installation of the lamp assembly can prevent the safety switch from being reactivated. Warning:When you replace the lamp assembly, always disconnect the projector from its power source. Do not rely solely on the safety switch to disconnect power from the assembly. Warning:The lamp assembly reaches extremely high tem- peratures during normal operation. If you need to replace the lamp assembly after operating the projector, let the unit cool in Standby mode for at least 30 minutes before attempting to remove the lamp assembly. When you use the Standby mode, power is still being fed to the projector. Do not try to replace the lamp assembly or any electronic components unless you unplug the unit from the power source. Maintenance31
Troubleshooting guide Symptom Cause Solution Projector does not Lamp-assembly door Refer to lamp assembly turn on; not closed correctly replacement procedure no lights or fan and verify proper installation No power to unit Try another electrical outlet Blown input power fuse(s) Call Polaroid Technical Support Vertical bars appear Nonstandard computer Press the IMAGE key and across the image clock rate scroll to PHASE; press < > cursor keys to remove the bars Image is upside down Incorrect projection Press the SETUP key mode selected and scroll to LOCATION; select DESKTOP or CEILING, as applicable Image rolls vertically Improper cables/ Check for correct cables loose cables and snug connection Incorrect computer setup Check computer video mode of operation (see Appendix B: Standards) 5 Troubleshooting
Symptom Cause Solution Solid-color screen is Projector is initializing If screen is displayed for displayed more than 15 seconds, press a source button associated with an active source Lamp does not light, Unit is in Standby mode Wait approximately green LED on rear and bulb-restrike timer 3 minutes, if bulb does not control panel is flashing has not elapsed light press the LAMP key Image is not in color Incorrect computer video Reboot your computer No projected image Improper cables/ Check for proper cables loose cables and snug connection CURTAIN (blue display) Press the CURTAIN key is on Active light source is not Verify proper connection selected and press source key associated with an active source Video source has not Common problem with been activated laptop computers, contact your computer dealer Where to get help If at any time you need help: 1Check the Troubleshooting guide. 2Call your dealer’s technical support line and explain your problem. 3Call Polaroid Corporation (see pages 35 and 36). Please have the serial number of your unit (located on the underside of the projector) available when you call. 34Troubleshooting
Troubleshooting35 Polaroid Offices and Service Centers Australia Polaroid Australia Pty. Ltd. 13–15 Lyonpark Road P.O. Box 163 North Ryde, N.S.W. 2113 Tel.: (02) 9 950 7000 Fax: (02) 887 2209 Belgique/België Polaroid (Belgium) N.V.–S.A. Rue Colonel Bourg 111 Kolonel Bourgstraat 111 1140 Bruxelles–1140 Brussel Tel.: 32 2 702 86 20 Fax: 32 2 726 92 99 Toll free: 32 78 155 905 Brasil Polaroid do Brasil Ltda. Av. Paulista, 1776–11º andar Cerqueira Cesar São Paulo–Capital 01310-921 Tel.: 55.11.285.6411 Fax: 55.11.283.2625 288.6521 287.5393 Canada Polaroid Canada Inc. 350 Carlingview Drive Etobicke, Ontario M9W 5G6 Toll free: 1-800-268-6970 Danmark Polaroid a.s. Blokken 75 3460 Birkerød Tlf.: 42 81 75 00 Fax: 42 81 70 26 Deutschland Polaroid GMBH Sprendlinger Landstrasse 109 63069 Offenbach Tel.: 069 8404 1 Fax: 069 8404 204 España Polaroid (España), S.A Calle Orense, 16 2 aplanta 28020 Madrid Tno: 34-1-597.02.52 Fax: 34-1-597.27.82France Polaroid (France) S.A. B.P. 7 78996 Elancourt Cédex Tel.: (1) 30 68 38 38 Fax: (1) 30 68 38 39 Hong Kong Polaroid (Far East) Ltd. 32/F Windsor House 311 Gloucester Road Causeway Bay Tel.: (852) 2894 0333 Fax: (852) 2895 1382 Italia Polaroid (Italia) S.p.A. Via Piave 11 21051 Arcisate (Varese) Tel.: 0332-470031 Fax: 0332-478249 Japan Nippon Polaroid Kabushiki Kaisha Mori Building No. 30 Toranomon 3-2-2 Minato-ku Tokyo 105 Tel.: 81-3-3438-8811 Fax: 81-3-3433-3537 México Polaroid de México S.A. de C.V. Paseo de la Reforma 195 Piso 17 C.P. 06500 México, D.F. Tel.: 703-1111 Fax: 566-0505 Del interior al 91 (800) 70-727 Ventas 91 (800) 70-747 Nederland Polaroid Nederland B.V. Zonnebaan 45 3606 CH Maarssen PO Box 1219 3600 BE Maarssen Tel.: 31-30-2-410-420 Fax: 31-30-2-411-969 Reparaties: Polaroid (Europe) B.V. Hoge Bothofstraat 45 7511 ZA Enschede Tel.: 31-53-4-865-400
36Troubleshooting New Zealand Polaroid New Zealand Ltd. Camera Services 24-26 Anzac Avenue Auckland Tel.: (09) 377 3773 Norge Polaroid (Norge) A/S Industriveien 8B, 1473 Skårer Postboks 80, 1471 Skårer Tlf: 67 90 47 10 Fax: 67 90 51 73 Österreich Polaroid Ges.m.b.H. Eitnergasse 5A 1231 Wien Tel.: 869 86 27 Fax: 869 81 00 Portugal Polaroid (España) S.A. Sucursal em Portugal Edificio Monumental Avenida Praia da Vitória, 71-A 4º B 1050 Lisboa Tel.: (01) 316.10. 52 Puerto Rico Polaroid Caribbean Corporation Centro de Seguros Ave. Ponce de León 701 Miramar, Santurce 00907 Tel.: (809) 725-6240 Fax: (809) 725-5462 Schweiz/Suisse/Svizzera Polaroid AG Hardturmstrasse 133 8037 Zürich Tel.: (01) 277.72.72 Suomi Polaroid Oy Sinikalliontie 10 02630 Espoo Puh: 90-502 35 33 Fax: 90-502 35 50 Sverige Polaroid AB Ekholmsvägen 34 Box 204 127 24 Skärholmen Tel.: 08-710 08 50 Fax: 08-740 73 68 U.K. Polaroid (U.K.) Ltd. & Polaroid Export Operations Wheathampstead House Codicote Road Wheathampstead Hertfordshire AL4 8SF U.K. Tel: (44) 1582 632000 Freefone: 0800 010119 U.S.A. Polaroid Corporation Technical Assistance Tel.: Toll free 1-800-432-5355 Call for the nearest Polaroid location
Troubleshooting37 One Year Warranty Polaroid Corporation warrants your Polaview Projector equipment against defects in manufacture for a period of one year from the date of purchase. To verify the warranty period, you should keep the sales slip or other proof of the purchase date. Should this product, or any component or accessory included with it, become defective at any time during the warranty period, Polaroid Corporation will, at its discretion, either replace or repair this item, without charge, provided the product is returned to a designated servicing location (prepaid and insured). To ship the unit, pack the carrying case in the original carton or equivalent, with plenty of padding. This Limited Warranty does not apply to product damage resulting from accident, incorrect installation, unauthorized modification, misuse or abuse. U.S.A. and CanadaBefore you return your equipment for repair, please call Polaroid Electronic Imaging Technical Support from within the U.S.A. at 1-800-432-5355, Monday through Friday, 8 a.m. to 8 p.m., Eastern Time. In Canada, call 1-800-268-6970. We can help you determine what is at fault, and advise you on how and where to get service in the quickest and most convenient way. THIS WARRANTY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL EXPRESSED OR IMPLIED LIABILITY FOR THIS EQUIPMENT INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE ONE-YEAR WARRANTY PERIOD.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR THE DURATION OF IMPLIED WARRANTIES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. Outside the U.S.A.THIS WARRANTY EXCLUDES ALL INCIDENTAL AND and CanadaCONSEQUENTIAL DAMAGES AND DOES NOT AFFECT YOUR STATUTORY RIGHTS. Note: No user-serviceable parts inside, with the exception of the lamp assembly which can be replaced as described in this manual. Attempts to modify mechanical or electronic parts inside will void your warranty, and may be hazardous. 38Maintenance