Polaroid Projector Polaview 110 User Manual

C o n n e c t o rD e s c r i p t i o n
hAUDIO OUT Provides audio output to an 
external stereo system.
iRGB OUTProvides computer output to a
separate monitor.
jC O N T R O LConnects to a serial cable for
computer control.
kPower switch Turns power on and off.Control panel
The projector control-panel keys are used to turn the projec-
tor on or off, adjust the projected image, and to display and
hide the menu. Power, warning, and alert lights give you
important information about how your projector is...

K e yF u n c t i o nM E N UControls the menu.R E S E TResets the image to the factory defaults.O NFlashes green during start-up.
Glows green if AC input and projector
power supplies are functioning. 
Glows red if they are not, 
or if the air filter door is removed.T E M PGlows red to warn of an over-temperature
condition. Flashes red if the fan is not 
w o r k i n g .L A M PGlows red if the projection lamp burns o u t .
Options andCyclops interactive pointer system
accessoriesThe Proxima Cyclops...

2 Detailed setupYour Polaview Model 110 Projector
Before you begin, examine the components of the
projector.
The Polaroid Polaview
Model 110 Projector and
the Cyclops
Remote Control
aHandlegConnector panel
bInternal speakerhAC power switch
cInfrared lensiPower-cord receptacle
dProjection lens assemblyjBottom intake filter
eControl panelkRemote control
fRear exhaust 

Getting started
Place the projector on a solid, flat surface at a right angle
(perpendicular) to the projection screen and parallel to the
floor. If you use a media cart, make sure the wheels are
locked to prevent it from moving.
Positioning 
the projector10Detailed setup 

Transporting andThe projector has a recessed handle located in one of the 
moving the projectorside panels. Always use the handle to transport the projec-
tor. The projector has protective feet on the side opposite
the handle, as well as on the bottom.
Transporting 
the projector
If you are moving the projector a short distance, grasp the
sides of the projector securely, as shown below, to stabilize
the weight of the unit.
Moving 
the projector Detailed setup11 

Projector coolingThe air intake grill is on the bottom of the projector. The air 
and airflowexhaust grill is on the rear panel.
Caution! Never operate the projector if these grills are
clogged or obstructed, or if the electric fans are not running.
Allow for proper 
airflow12Detailed setup 

Connector panel
All connections between the projector and your computer
or video source are made on the side connector panel.
The connector panelC o n n e c t o rD e s c r i p t i o n
aVIDEO 1 & 2 Connects to video output from anNTSC, PAL, or SECAM source.bS-VIDEO 1 & 2 Connects to an S-Video source.
cCYCLOPS port Connects your computer to the Cyclops interactive pointer system.
dAUDIO IN 1 & 2 Connects to stereo/mono audiooutput  from the computer.
eRGB IN 1 & 2  Connects computer video to the p r o j e...

C o n n e c t o rD e s c r i p t i o n
gL-AUDIO-R 1 & 2 Connects to stereo/mono audio 
output from an NTSC, PAL, orSECAM source.
hAUDIO OUT Provides audio output to an external stereo system.
iRGB OUTProvides computer output to aseparate monitor.
jC O N T R O LConnects to a serial cable forcomputer control.kPower switch Turns power on and off. 14Detailed setup 

Supplying power to the projector
The power-cord receptacle and AC power switch are located
below the projector connector panel.
Power receptacle
and AC power
switch
aPower receptacle 
bAC power switch
To supply power to the projector:
1Plug the appropriate power cord into the power receptacle
on the side of the projector.
2Connect the power cord to a properly-grounded wall outlet.Detailed setup15 

Computer video and audio connections
Connecting a PCUse the included VGA video cable to connect your PC to the
projector. If you want to use your monitor and projector at
the same time, use your existing monitor cable to connect
the projector to a separate monitor. 
VGA video cable
VGA connections
1Unplug the monitor cable from the computer.
2Plug one end of the supplied VGA cable into the RGB IN 1
port on the projector. Plug the other end of the VGA cable
into the computer Video Out (VGA) port....