Polaroid Polaview 360 Projector User Manual
Have a look at the manual Polaroid Polaview 360 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 15 Polaroid manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31Example of system setupCleaning the Air filterTurn power off to all devices before connecting. Refer to the instruction manual of each device before connecting.AC input Video tape recorder with S jack Video tape recorder Speaker (with built-in amp) Display monitor Computer (desktop type)Computer (notebook type) Clean the air filter about every 100 hours .1Turn off the MAIN POWER switch of the projector and pull out the power cord.2Remove the front air filter.F i l t e rParts Number Air FilterM U 0 0 8 3 1
32Cleaning the Air filter(continued)3Cleaning the air filter with a vacuum cleaner4Installing the air filterWhen the air filter becomes clogged with dust, etc., the projector power may turn off to prevent the internal heat level rising. (The lamp indicator color changes to red.) Do not operate the projector with the air filter removed. (If used with the air filter removed, dust can enter the LCD panel and produce an adverse effect on image quality.)LampMessage tableEven when the lamp is at a high temperature, the power to the projector may cut off to prevent an excessive temperature increase inside the projector. (The POWER indicator turns off.) Turn o ff the MAIN POWER switch, wait for some 20 minutes and turn on the MAIN POWER switch again. If the projector is not recovered after turning on the MAIN POWER switch, please contact your dealer or service company.The light source lamp has a service life. When used for an extended time, the images may become darker and the colors may deteriorate. A malfunction could occur if the projector is used in this condition, so replace the lamp with a new one. The following indicator or a message which appears when the power is turned on will indicate when the lamp should be replaced. At such time, it is necessary to replace the lamp with a new one. For lamp replacement, please contact your dealer or service company. The following messages are displayed on the screen.*1 This display will disappear after 3min. but will reappear when the power is turned on again.Screen displays CHANGE THE LAMP“CALL A MAINTENANCE PERSON” “CHANGE THE LAMP” “CALL A MAINTENANCE PERSON” “THE POWER WILL TURN OFF AFTER *hr.” Blinking of “CHANGE THE LAMP” NO INPUT IS DETECTED SYNC IS OUT OF RANGEThe total lamp usage time is nearing the service life of the lamp. Replace with a new lamp. The lamp will turn off automatically when the lamp replacement time has been exceeded. *1 The total lamp time is nearing the lamp replacement time. After (*) hours, the lamp will turn off. Quickly replace witha new lamp. *1 *Indicates the number of hours until the lamp turns off automatically. The total lamp time has exceeded the replacement time. The indicator will blink for approximately 10 min. and then turn off automatically. Replace with a new lamp. There is no signal input (refer to pages 22, 23). The current horizontal or vertical frequency cannot be used by this projector (refer to pages 23, 24).
33Message table(continued) Indicators The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases.POWER indicator Lights orange Flashes green Lights green Flashes orange Lights red Lights red Lights red Flashes redLAMP indicator Turns off Turns off Turns off Turns off Lights red Flashes red Turns off Flashes redTEMP indicator Turns off Turns off Turns off Turns off Turns off Turns off Flashes red Turns offStatus Standby status Warming up Operation status *1 Cool down The lamp does not light. *2 The interior is too hot. A lamp has not been inserted or the lamp cover is missing. The cooling fan is not operating. The total lamp time has exceeded the replacement time.Processing Wait some time (approx. 20 min.) before turning the power on again. Clean the air filter before turning the power on. If the indicator still lights, contact your dealer. Contact your dealer. Contact your dealer. Contact your dealer. When the LAMP or TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your dealer or service company. *1: When the cooling fan is stopped and the interior becomes overheated, the power will turn off automatically to allow cooling (the indicator will turn off). In such cases, turn off the projector power, allow the set to cool and then turn the projector power on again. The lamp will then light. If the lamp does not light, contact your dealer or service company. *2:In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP indicator will flash red. In such cases, turn off the MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.When you think something wrong Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.Symptom The power is not turned on. No video or audio. Video is present but no audio. Audio is present but no video. Colors are pale and color matching is poor.Images are dark. Video is blurred. The LAMP indicator lights red.Possible cause •The main power switch is not turned on. •The power cord is disconnected. •The input is not correctly set. •No signal input. •The projector is not correctly connected. •The volume is set to minimum. •Mute is turned on. • Audio is switched to RGB when P in P is on.•The projector is not correctly connected. •The brightness adjustment knob is rotated fully clockwise. •The lens cap is still on. Color density and color matching are not correctly adjusted. • Brightness and contrast are not correctly adjusted.•The lamp is nearing the end of its service life.Focus or H PHASE is out of adjustment. Lamp failure. Internal overheating.Remedy • Turn on the main power switch.•Plug the power cord into an AC power outlet.•Use the projector or remote control to set. •Connect correctly. •Connect correctly. • Press VOLUME + on the remote control or display the menu screen and adjust the volume.•Press the MUTE button. • Displays the Volume bar and switches the Audio input.•Connect correctly. •Select BRIGHT with the MENU button and then press the ( ) key. •Remove the lens cap. Adjust the video. •Adjust the video. •Replace with a new lamp. Adjust the focus or H PHASE. Wait approximately 20 min. and then turn the power on again. • Make sure the ventilation openings are not blocked.•Clean the air filter. • Lower the ambient temperature to 35 degrees C or less.Page P.13 P.9 P.8,10, 13,19 P.9,31 P.9,31 P.10,18 P.8,10 P.10 P.9,31 P.17 P.13 P.18 P.18 P.32 P.13,18 P.33 P.31,32
34Specifications Dimensional Diagram·These specifications are subject to change without notice.Unit: inchesProduct nameLiquid crystal projector ModelPolaroid360 Display methodThree liquid crystal panels, three primary color system. Liquid crystal Panel size3.3 cm (1.3 type) panelDrive systemTFT active matrix Number of pixels786,432 pixels (1,024 horizontal´768 vertical) Lens Zoom lens F=1.7~2.3 f=49~64mm Lamp190w UHB Speaker1.2W + 1.2W (Stereo) Power supplyAC100 ~ 120V, 3.7A / AC220 ~ 240V, 1.5A. Power consumption320W Operating temperature range0 ~ 35˚C Size11 (W) ´5 (H) ´14 (D), 289mm(W) ´ 124mm(H) ´345mm(D) Weight (mass)13 lbs, 5.9kg S VIDEO: mini DIN 4-pin jack VIDEO signal input jacksVIDEO: RCA jack AUDIO: RCA jack RGB signal input/output jacksRGB signals: D-sub 15-pin shrink jack Audio: stereo mini-jack CONTROL signal jackD-sub 15-pin shrink jack USB jackB type