Plus Projector U5 732 User Manual

							E-51
White Balance
This function automatically adjusts the black level and the white level of
the analog RGB input signal to suit the personal computer.
1 Select the item name [White Balance] and press the ENTER button.
The display will change to [Input Black Signal].
2 The screen background color of the connected personal computer
will be set to black.
3. Press the ENTER button. The display will change to [Adjusting Black]
and the black level will be adjusted.
4 The adjustment of the black level is completed and the display
changes to [Input White Signal].
5 The screen background color of the connected personal computer
will be set to white.
6 Press the ENTER button. The display will change to [Adjusting White]
and the white level will be adjusted.
[White balance complete] is displayed for a while and the adjustment is
completed.
Color 
						

							E-52
View
•Perform this operation while projecting the picture for which the adjustment/setting will be made.
•Select the menu name “View”.
See “Menu Operation Method” on Page E-40 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-45.
Aspect
This function sets the horizontal and vertical picture proportions of the
input signal.
Select the item name “Aspect” and select the setting contents with the
SELECT () buttons.
Video Signals
Auto ............ While maintaining the aspect ratio, projects a full screen
so that no portions extend beyond the boundaries of the
screen. The top and bottom of the 16:9 image becomes
black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a
proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the
screen. (Portion that extend off screen is cut.)Aspect ratio selection Auto Wide Zoom
4:3 screen
16:9 screen
Personal Computer Signal
Auto ............ Automatically enlarges or reduces the image to project
a full screen in a ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the
maximum displayable size
Real ............ Projects the input signal without pixel conversionInput Signal Auto Direct Real
The setting is higher
than the display reso-
lution of the projector.
The setting is lower
than the display reso-
lution of the projector.
Note:
Please note that using this monitor for the purpose of commercial gain or the at-
traction of public attention in a venue such as a coffee shop or hotel and projecting
a 4:3 screen in wide mode or leaving a squeezed screen as a compressed image
raises concern about the infringement of the copyright holder’s rights which are
protected by copyright law.
Note:
When selection has been made for the “Real” setting of the personal computer
signal (i.e., when the input signal and the projector display resolution are high) and
the “Zoom” setting of the video signal, pressing the SELECT (

) buttons on
the remote control will permit movement of the display position. Note that there will
not be any movement when the menu or the quick menu is displayed.
Filter
This function sets the sharpness when the input signal is adjusted to
the resolution of the projector and enlarged or reduced.
Select the item name “Filter” and select the setting contents with the SELECT
() buttons.
Smaller numerical values result in a sharper picture and larger values result in
a softer picture. Please select your desired setting value. 
						

							E-53
Vertical Flip / Horizontal Flip
In selecting the method of projecting to the screen, these functions are
set when the projector is in a suspended or a rear screen installation.
Select the item name “Vertical Flip” or “Horizontal Flip” and select the setting
contents with the SELECT () buttons.
View
“Vertical Flip” Off
“Horizontal Flip” Off“Vertical Flip” Off
“Horizontal Flip” On“Vertical Flip” On
“Horizontal Flip” On“Vertical Flip” On
“Horizontal Flip” Off
Keystone
Keystone distortion will occur when the projector and screen are on an
angle (in the vertical orientation). This function is used to correct this
distortion.
Select the item name “Keystone” and correct the keystone distortion using the
SELECT () buttons.
Press the  button. Press the  button.
Note:
* The menus and other on-screen displays cannot be adjusted.
* Please note that depending on the projected picture and the projection condi-
tions, it may not be possible to eliminate keystone distortion completely.
This function is used to save the keystone adjustment values.
Setting Keystone Save to on will set the previous keystone adjustment values
when projecting after the power cable has been disconnected and then recon-
nected.
Select the item name “Keystone Save” and set with the SELECT () buttons.
Off .............. The keystone adjustment values return to the initial values when the power
cable is unplugged.
On ............... The keystone adjustment values are retained in storage even when the
power cable has been unplugged.
Note:
Regardless of whether Keystone Save is set to “On” or “Off”, when projection is
from the standby condition, the picture is projected using the previous keystone
adjustment values.
Keystone Save 
						

							E-54
Setup
•Select menu name “Setup”.
See “Menu Operation Method” on Page E-40 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-45.
The Auto Source function automatically detects the input signal when
the power supply is switched on and when the input is switched.
Select the item name “Auto Source” and select the setting contents with the
SELECT () buttons.
On ............... Switches on the automatic detection function
Off .............. Switches off the automatic detection function
Signal Detection Order When On
The sequence of RGB → VIDEO → S-VIDEO is searched repeatedly.
When a signal is detected, the search is stopped and the image is projected.
Auto Source
This function switches off the projector power automatically when the
input of the projector enters a no-signal condition.
Select item name “Auto Power Off” and select the setting contents with the
SELECT () buttons.
On ............... The power is switched off when there is no signal.
Off .............. The power is not switch off even when there is no signal.
Operation when Function is On
•The “No Signal Power Off” display appears when a no-signal condition con-
tinues for approximately 10 seconds. The power is switched off about 5
minutes after this.
•If a signal is input during the appearance of the display and an operation
button other than the STANDBY button is pressed, the display is closed and
the function is cancelled.
Auto Power Off
Note:
Some video decks and other equipment output a blue background or other video when playback ends. When this happens, a signal is being
input to the projector and Auto Power Off is not activated. 
						

							E-55
Setup
Menu Position
This function sets the display position of the menu.
Select item name “Menu Position” and select the setting contents with the
SELECT () buttons.
............. Displays on the left side
............. Displays on the right side
Lamp Mode
Use this if the picture is projected on a small screen and the picture is
too bright or when projecting images in dark rooms.
Select the item name “Lamp Mode” and select the setting contents with the
SELECT () buttons.
Eco ............. The lamp brightness is set to 80% and the lamp life is extended.
(STATUS indicator is green)
Normal ....... The lamp brightness is set to 100% and the screen is bright.
(STATUS indicator is off)
Note:
Frequent switching this mode can degrade the lamp.
STANDBY STATUS
STATUS Indicator 
						

							E-56
Setup
Input Format
This function is used in setting the input signals of the input connec-
tors.
Normally, this should be set to Auto. When identification is not possible
with Auto, make the setting.
Select the item name “Input Format”, press the ENTER button, and the sub
menu will open.
Select the connector that is to be changed, and select the setting contents
with the SELECT () buttons.
[RGB]
This is the signal setting for the RGB connector.
Auto ............ Automatically identifies the signal.
RGB ............ Analog RGB signal is set.
Component . Component signal is set.
[Video] and [S-Video]
[Video] is the color system setting for the VIDEO connector and [S-Video] is
the color system setting for the S-VIDEO connector.
Auto ............ Automatic identification.
NTSC .......... Fixed to the NTSC system.
NTSC 4.43 .. Fixed to the NTSC 4.43 system.
PAL ............. Fixed to the PAL system.
PAL M ......... Fixed to the PAL M system.
PAL N ......... Fixed to the PAL N system.
PAL 60 ........ Fixed to the PAL 60 system.
SECAM ....... Fixed to the SECAM system.
Presentation Timer
The presentation is given while checking the timer displayed on the
screen.
The gauge display allows the remaining time to be known at a glance.
Select the item name “Presentation Timer” and select the setting contents
with the SELECT () buttons.
Setting contents:Off, 10 min. , 20 min. , 30 min. , 40 min. , 50 min. , 60 min.
To start the timer...
Press the MENU button and open the menu.
The timer display will appear at the lower right and the timer will start.
See “Using the Presentation Timer” on Page E-33 for details. 
						

							E-57
Option
•Select menu name “Option”.
See “Menu Operation Method” on Page E-40 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-45.
Language
This function sets the language that is displayed on screen in
the messages and menu displays.
Select item name “Language” and press the ENTER button to open
the Language sub menu.
Select the language with the SELECT (
) buttons.
On Screen
This function switches on/off the messages displayed with a black
frame such as the input signal information and the aspect ratio.
Select item name “On Screen” and select the setting contents with the
SELECT () buttons.
On ............... The message is displayed.
Off .............. The message is not displayed.
Note:
Even when set to off, messages that are not in a black frame will be dis-
played.
Example of a display when the
FREEZE button is pressed
Freeze
Background
This function sets the screen color when the input source is no-
signal.
Select item name “Background” and select the setting contents with
the SELECT () buttons.
Blue ............ Sets a blue screen when there is no signal
Black ........... Sets a black screen when there is no signal 
						

							E-58
Startup Screen
This is the selection of whether or not to display the logo screen
at startup time.
Select item name “On Screen” and select the setting contents with the
SELECT () buttons.
Logo ........... Displays the logo.
Blank .......... Does not display the logo.
Note:
When “Logo” is selected at the startup screen, the “PLUS” logo is dis-
played.
Option
Security Lock
A password can be registered and the security lock set in order
to prevent unauthorized use of the projector.
For instructions on using the security function, see “Protecting the
Projector with the Security Lock” on E-37.
Select item name “Security Lock” and select the setting contents with
the SELECT () buttons.
Disable ....... The security lock is disabled.
The projector can be operated without inputting the password.
Enable ......... The security lock is enabled.
The security lock is activated when the power is turned on, and
the password must be input in order to operate the projector. 
						

							E-59
Info.
•Select menu name “Info.”.
See “Menu Operation Method” on Page E-40 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-45.
Status
This displays information about the equipment.
Select item name “Status” and press the ENTER button.
There is a change to the status display.
Press the CANCEL button to return to the menu.
Display Contents:
Projector model, firmware version, and the internet home page ad-
dress of PLUS Vision Corp.
Lamp Timer Reset
This function resets the lamp timer. Be sure to perform the reset
operation when the lamp cartridge has been replaced.
Select item name “Lamp Timer Reset” and press the ENTER button.
There is a change to the display “Press “ENTER” to Lamp Timer Re-
set”.
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
Factory Default
This function returns the adjustments and settings of all the in-
put sources to the standard factory default values.
Select item name “Factory Default” and press the ENTER button.
There is a change to the display [Press “ENTER” to Factory Default
Set].
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
Items that are not set to the factory default:
Vertical Flip / Horizontal Flip, Language, Security Lock and Lamp Timer. 
						

							E-60
Resolution / Frequency
This function displays the resolution and frequency of the detected in-
put signal.
Info.
Lamp Timer
This displays the lamp timer.
This projector has an Eco mode function. The lamp life will differ between
Normal mode and Eco mode.
Lamp Life
Use only in Normal mode: approx.2000 hours
Use only in Eco mode: approx.3000 hours
* Lamp life will differ when there has been switching between the modes.
•When Lamp Life Has Been Reached
“Replace the Lamp Cartridge” is displayed on the screen for 10 seconds in
a 1-minute interval.
Please replace the lamp with a new one.
See “Replacing the Lamp Cartridge” on Page E-64 for information about
lamp cartridge replacement.
•When Over 100 Hours Have Elapsed Since Reaching Lamp Life
(Including Eco Mode)
[Warning!! System Shutdown] is displayed for 10 seconds and the power is
switched off. Pressing the STANDBY button under this condition will not
switch on the power. Please replace the lamp cartridge.