Plus He 3100 Projector User Manual

E – 11
Preparing the Remote Control
Inserting the Batteries
When using the remote control for the first time, install the batteries that were supplied.
When replacing batteries, purchase two of the same type of AA battery.
Press and at the same time lift
the battery case cover at the
rear of the remote control to
remove it.
1
Follow the markings on the inside
of the case and insert the batter-
ies in the correct plus (+) and mi-
nus (-) directions.
2
First insert the tabs of the battery
case cover, then...

E – 12
The Procedure Up to Projecting to the Screen
DVI-D COMPONENT
CTRL
S-VIDEOVIDEOY             Cb            Cr
POWER
ONOFF
POWER/STATUSON/STANDBYASPECTSOURCE
1
2
3
4
7
5
9
8
6
Note:
* Please purchase a commercially available screen separately.
* A cable (commercially available), which is available separately,
is required for connections with the DVI-D connector of the
personal computer.
* A cable (commercially available), which is available separately,
is required to connect a DVD player with the...

E – 13
Placement Guide
Use this information as a guide to find the rough screen size when the projector is placed at a certain location, or to find out the
approximate size of a screen that will be required.
The projection distance over which focussing is adjustable is 1.2 m (3.9 feet) to 6.9 m (22.6 feet) from the Lens surface of the main
unit. The projector should be placed within this range.
 1  Projection Distance and Screen Size
3m (9.8 feet)
2m (6.6 feet)
1m (3.3 feet) 4m (13.1 feet)
1m
(3.3...

E – 14
Power Cord Connections
 2  Power Cord Connections
Use the supplied power cord to connect the power connector of the main unit with the power outlet.
POWER
ON OFF
POWER/STATUSON/STANDBYASPECTSOURCE
POWER
1
4
2
3
POWER switch
POWER/  indicator
Firmly insert all the way.
Power cord (supplied)
Firmly insert all the way.To wall outlet
Attention!
For pluggable equipment, install the projector as near to the power outlet socket that is easily accessible.
Do not switch off the main power or disconnect the...

E – 15
Connecting Video Equipment and Personal Computers
By connecting this unit with video equipment and using a DVD player or other source in combination with an audio/video amplifier
and speaker system will allow you to enjoy convincing home theater. Connecting the unit to a personal computer will permit
presentation data to be projected as a large screen display in conferences and lectures.
 3  Connections with VIDEO and S-VIDEO Connectors
These are connections made with equipment that is equipped...

E – 16
D
VI-D CO
M
PONENT
CTRL
S
-VIDE
OVIDEOY             Cb            Cr
COMPONENT
S-VIDEOVIDEOY             Cb            Cr
YCbCrCOMPONENT
G
BRG
BR
 3  Connections with YCbCr Connectors
These connections are made with equipment such as a DVD player that is equipped with the YCbCr output jacks of the component
signals.
Make connections to the Y, Cb, and Cr jacks (COMPONENT) of the main unit.
Component signal cable
(commercially available)
Make connections to the YCbCr
output jacks marked COMPONENT
or...

E – 17
D
V
I-D C
O
M
P
O
N
E
N
T
C
T
R
L
S
-
V
ID
E
OV
ID
E
OY
             C
b
            C
r
MONITOR OUTPUT
DVI-D
DVI-D
CTRL
 3  Connection with DVI-D Connector
This connection is made with personal computers that are equipped with a display output DVI-D connector.
Make the connection with the DVI-D connector of the main unit.
Check the following before making connections.
* The resolution through this unit is S-VGA 800 x 600 dots. VGA is enlarged and displayed and XGA is compressed and displayed....

E – 18
Turning ON or OFF Main Power
POWER
ON OFF
STATUSPOWER/
POWER
ON OFF
POWER/STATUS
Main power ON
Main power OFF
 4  Turning ON or OFF Main Power
Before turning the main power, check that the power is switched off the equipment that is to
be connected and the connection is finished.
To turn on the main power:
Press the POWER switch down until it is in the depressed po-
sition.
On condition
Off conditionLight in orange
Indicator OFF
To turn off the main power:
Press the POWER switch until it is in the...

E – 19
POWER/STATUSON/STANDBYASPECTSOURCE
Adjustment of the Projection Screen
Operations include the adjustment of the image position that is projected to the screen and the adjustment of the focus as well as
the input selection and the selection of the aspect ratio.
Perform these operations with the power of the connected equipment switched on and the video signal input to the projector.
 6  Projection Screen Position Adjustment
1
Adjust the projection image to the screen
(1) If the image is shifted to...

E – 20
 8  Input Selection
3
Press the SOURCE button and select
the desired connector .
SOURCE
A press of the SOURCE button will display the
currently selected input selection.
Each press of the button moves the selection
one step in the sequence:
VIDEO → S-VIDEO → YCbCr → DV I
The selection will not change while Now Search-
ing is displayed.
The display will remain for a while before disap-
pearing. To change the duration of the display,
see → Page E-35 On-Screen Display Duration
Setting.
S-VIDEO...