Planet Technology Router XRT-412 User Manual

2.3 PPPoE 
 
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP 
should provide all the information required in this section. 
 
 
 
Parameter   Description 
 
User Name Enter the User Name provided by your ISP for the PPPoE 
connection  
 
Password Enter the Password provided by your ISP for the PPPoE 
connection 
 
Service Name This is optional. Enter the Service name if your ISP requires it, 
otherwise leave it blank. 
 
MTU This is optional. You can specify...

WAN line breaks down and latter links again, the router will not 
auto-connect to the ISP. 
 
Idle Time You can specify an idle time threshold (minutes) for the WAN 
port. This means if no packets have been sent (no one using the 
Internet) during this specified period, the router will automatically 
disconnect the connection with your ISP. 
 
TTL Select Enable to plus 1 count in TTL response when user try to 
ping Internet IP address from LAN. By default, the feature sets to 
Disable. 
 
 
Click  when...

2.4 PPTP 
 
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP 
should provide all the information required in this section. 
 
 
 
Parameter   Description 
 
Obtain an IP address The ISP requires you to obtain an IP address by DHCP before   
Automatically                            connecting to the PPTP server.  
          
Use the following IP                 The ISP gives you a static IP to be used to connect to the PPTP 
Address...

Password Enter the Password provided by your ISP for the PPTP 
connection. 
 
PPTP Gateway If your LAN has a PPTP gateway, then enter that PPTP gateway 
IP address here. If you do not have a PPTP gateway then enter 
the ISP’s Gateway IP address above. 
 
Connection ID This is the ID given by ISP. This is optional. 
 
MTU This is optional. You can specify the maximum size of your 
transmission packet to the Internet. Leave it as it is if you do not 
wish to set a maximum packet size. 
 
BEZEQ-ISRAEL...

2.5 L2TP 
 
Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP 
should provide all the information required in this section. 
 
 
 
 
Parameter   Description 
 
Obtain an IP address The ISP requires you to obtain an IP address by the DHCP  
Automatically                            address by DHCP before connecting to the L2TP server. 
          
Use the following IP                 The ISP gives you a static IP to be used to connect to the L2TP 
Address...

 
L2TP Gateway If your LAN has a L2TP gateway, then enter that L2TP gateway 
IP address here. If you do not have a L2TP gateway then enter 
the ISP’s Gateway IP address above. 
 
MTU This is optional. You can specify the maximum size of your 
transmission packet to the Internet. Leave it as it is if you do not 
wish to set a maximum packet size. 
 
Connection Type If you select “Continuous”, the router will always connect to the 
ISP. If the WAN line breaks down and links again, the router will 
auto...

2.6 Telstra Big Pond 
 
Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the 
Internet. Your ISP should provide all the information required in this section. Telstra Big Pond 
protocol is used by the ISP in Australia. 
 
 
 
 
Parameters    Description 
 
User Name Enter the User Name provided by your ISP for the 
Telstra Big Pond connection  
 
Password Enter the Password provided by your ISP for the Telstra 
Big Pond connection 
 
User decide login server...

 
 23 

Chapter 3 General Settings 
Once you click on the General Setup button at the Home Page, you should see the screen below. 
 
If you have already configured the Quick Setup Wizard you do NOT need to configure anything 
thing in the General Setup screen for you to start using the Internet.  
 
The General Setup contains advanced features that allow you to configure the router to meet 
your network’s needs such as: Address Mapping, Virtual Server, Access Control, Hacker Attack 
Prevention, Special...

3.1 System 
 
The system screen allows you to specify a time zone, to change the system password and to 
specify a remote management user for XRT-412. 
 
 
 
Parameters    Description 
 
3.1.1 Time Zone Select the time zone of the country you are currently in. 
The router will set its time based on your selection.  
 
3.1.2 Password Settings Allows you to select a password in order to access the 
web-based management website. 
 
3.1.3 Remote Management You can specify a Host IP address that can perform...