Planar Pr6022 Projector User Manual

							DLP® Projector – User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
 
Item Label Description See page:
1.   (Power) Turns the projector On or Off  11 
2.  ▲
 (Up cursor)  Navigates and changes settings in the OSD 18 
Green  Power On  
Off   Power Off (AC Off) 3.  Power LED 
Flashing Error code
 
On System over temperature 
4.  Over Temp LED 
Off Normal State 
Orange Lamp is ready to be powered-on. 
5.  Ready LED 
Flashing Lamp not ready (Warm-up/shutting down/cooling)  
(see 
LED Error Messages on page  42) 
6.  Menu Open and exits the OSD buttons 
7.  ◄ (Left cursor) /  
Source  Detects the input device 
Navigates and changes settings in the OSD 
8.  ▼
 (Down cursor)  Navigates and changes settings in the OSD 
9.  ► (Right cursor) / 
Auto  Optimizes image size, position, and resolution 
Navigates and changes settings in the OSD 
18 
— 3 —  
						

							DLP® Projector – User’s Manual 
Rear view 
 
 
Item Label Description See page: 
1.  AC IN  Connect the power cable 11 
2.  USB (Service Only) Connect the USB cable from a computer  
(service only) 
3.  AUDIO 
Connect the AUDIO CABLE from the input device  
4.  S-VIDEO Connect the S-VIDEO CABLE from a video device 
5.  VIDEO Connect the VIDEO CABLE from a video device  
6.  VGA Connect the RGB CABLE from a computer and 
components 
10 
7.   (Security Lock) Secure to permanent object with a Kensington® 
Lock system 40 
 
Note: 
If your video equipment has both S-VIDEO and RCA
 jacks (composite video) connect to the  
S-VIDEO connector. S-VIDEO provides a better quality signal. 
– 4 –  
						

							DLP® Projector – User’s Manual 
— 5 — 
Bottom view 
 
Item Label Description See page: 
1.  Lamp cover Remove when changing the lamp. 35 
2.  Height adjustor  Adjuster drops down when adjuster button is 
pushed. 15 
3.  Lens cap hook  To fasten the lens cap cover. 
4.  Tilt adjustor 
Rotate adjuster lever to adjust angle position. 15 
5.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
 
Note: 
When installing, ensure that you 
use only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting  hardware and M4 screws with a maximum screw 
depth of 6 mm (0.23 inch). 
 
  
						

							DLP® Projector – User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with  bright fluorescent lighting turned on. Certain high-frequency fluores-
cent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the  path between the remote control and  the projector. If the path between 
the remote control and the projector is obstructed, you can bounce the signal off certain reflective sur-
faces such as projector screens. 
 
3. The buttons and keys on the projector have the sa me functions as the corresponding buttons on the 
remote control. This user’s manual describes  the functions based on the remote control.  
– 6 –  
						

							DLP® Projector – User’s Manual 
— 7 — 
 
Item Label Description See page: 
1.  Up cursor Navigates and changes settings in the OSD  
2.  Enter  Changes settings in the OSD 
18 
3.  Power Turns the projector On or Off 11 
4.  Right cursor Navigates and changes settings in the OSD 18 
5.  Volume +  Increase volume 
6.  Volume -  Decrease volume 
17 
7.  Mute  Mutes the built-in speaker 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device 10 
10.  Auto  Auto adjustment for frequency, tracking, size, position 
11.  Keystone top  Corrects image-trapezoid (wider top) effect 
12.  Keystone bottom  Corrects image trapezoid (wider bottom) effect 
16 
13.  Down cursor Navigates and changes settings in the OSD 
14.  Left cursor  Navigates and changes settings in the OSD 
15.  Menu  Opens the OSD  
18 
  
						

							DLP® Projector – User’s Manual 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radius of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the  projector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using t he remote control or the buttons on the top of the projector. All 
operations can be carried out with t he remote control; however, the buttons on the projector are lim-
ited in use. The following illustration shows the  corresponding buttons on the remote control and on 
the projector. 
Remote Control 
 
Some buttons on the projector have  multiple functions. For example, item 3/6/7 on the projector func-
tions as the keystone button  and as the down cursor key. 
 
 
– 8 –  
						

							 – 9  –
 
Setup and Operation 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the di-
rection of the arrow (A). Pull out the 
cover (B). 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the battery when not usi ng the projector for prolonged periods. 
 
 
 
  
						

							DLP® Projector – User’s Manual 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS  players, as well as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to confirm it has  the appropriate output connector.  
 
Item Label Description 
A 
USB (Service Only) Connect the USB cable from a computer (service only). 
B 
AUDIO Connect the audio cable from the computer’s audio-out connector. 
Connect the audio cable (mini jack-to-
RCA x 2) from a video device.  
C 
S-VIDEO Connect the S-video cable from a video device. 
D 
VIDEO Connect the video cable from a video device. 
 VGA Connect the RGB cable from a computer. 
Connect DVD input YCbCr / YPbPr, through optional RGB to 
COMPONENT ADAPTOR. E
 
Warning: 
As a safety precaution, disconnect all power to
 the projector and connecting devices before making 
connections. 
 
– 10 –  
						

							DLP® Projector – User’s Manual 
Starting and Shutting down the Projector 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
The 
 Power  and Ready  LEDs on 
the projector light. 
2.  Turn on the connected devices.  
3.  Ensure the Ready  LED displays a 
solid orange and not a flashing or-
ange. Then press the 
  Power  
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are de-
tected. 
 
See Setting an Access Password 
(Security Lock)  on page 13 if security 
lock is enabled. 
 
4.  If more than one input device is con-
nected, press the Source button 
and use  ▲▼ to scroll among de-
vices. 
(Component is supported through 
the RGB to Component adapter.) 
 
 
•  RGB: Analog RGB 
Component: DVD input YCbCr / YPbPr, or HDTV 
input YPbPr via HD15 connector 
• Composite Video: Traditional composite video 
• 
S-Video: Super video (Y/C separated) 
–  11  –  
						

							DLP® Projector – User’s Manual 
5.  When the “Power Off? /Press 
Power again” message appears, 
press the Power  button. The projec-
tor turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the  Ready LED stops flashing–indicating the projector has 
cooled down. 
 
– 12 –