Planar Pr5021 Projector User Manual

							
DLP® Projector – User’s Manual 
5.  When the “Power Off? /Press 
Power again” message appears, 
press the POWER  button. The pro-
jector turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the READY  LED stops flashing–indicating the projector has 
cooled down. 
 
– 13  –  
						

							
DLP® Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See 
Navigating the 
OSD
 on page  for help on using OSD menus.) 19
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact your reselle r for information on clearing the password. 
 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move 
to the Installation I  menu. 
 
3.  Press the cursor ▲▼ button to select  
Security Lock. 
4.  Press the cursor  ◄► button to enable 
or disable security lock function. 
A password dialog box automatically  
appears. 
– 14 –  
						

							
DLP® Projector – User’s Manual 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
 
Press the cursor buttons in any order 
to set the password. Push the  MENU 
button  to exit the  dialog box. 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the  Security Lock is enabled. 
Enter the password in the order you 
set it at step 5. In case you forget the 
password, please contact the service 
center.  
Service center will validate the owner 
and help reset the password.  
 
 
–  15  –  
						

							
DLP® Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, lift the projector  [A] and press the height-adjuster 
button [B] .  
The height adjuster drops down  [C].  
2.  To lower the level of the projector, press the height-adjuster button and push down on 
the top of the projector. 
3.  To adjust the angle of the picture, turn the tilt-adjuster  [D] right or left until the 
desired angle has been achieved. 
 
 
– 16 –  
						

							
DLP® Projector – User’s Manual 
– 17  – 
Adjusting the Focus, Zoom and Keystone 
1.   Use the  Image-focus   
control (on the projector 
only) to sharpen the 
projected image
A. 
2.   Use the  Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and 
screen size 
B.  
3.   Use the  KEYSTONE  
buttons (on the projec-
tor or the remote 
control) to correct im-
age-trapezoid (wider 
top or bottom)  
effect. 
Remote control and OSD panel
 
4.   The keystone control  
appears on the display. 
  
						

							
DLP® Projector – User’s Manual 
Adjusting the Volume 
1.  Press the Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
 
 
2.  Press the  Left or Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/-.  
 
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
– 18 –  
						

							
DLP® Projector – User’s Manual 
– 19  – 
On-Screen Display (OSD) Menu Settings 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illust ration shows the corresponding buttons on the re-
mote control and on the projector. 
 
 
 
1.  To enter the OSD, press the  MENU button.  
2.  There are five menus. Press the cursor  ◄► button to 
move through the menus.  
3. Press the cursor  ▲▼ button 
to move up and down in a 
menu.  
4. Press  ◄► to change values 
for settings. 
5. Press  MENU to close the 
OSD or leave a submenu. 
Note: 
Depending on the video source, not all items in  the OSD are available. For example, the Horizon-
tal/Vertical Position  items in the Computer menu can only be modified when connected to a PC. 
Items that are not available cannot  be accessed and are grayed out.  
   
						

							
DLP® Projector – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
 
– 20 –  
						

							
DLP® Projector – User’s Manual 
OSD Sub-Menu Overview 
 
– 21  –  
						

							
DLP® Projector – User’s Manual 
Image Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  Image 
Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
values for settings. 
 
Item Description 
Display Mode Press the cursor ◄►  button to set the Display Mode.  
Brilliant Color Press the cursor ◄►  button to adjust the Brilliant Color value. 
Brightness Press the cursor ◄► button to adjust the display brightness. 
Contrast Press the cursor ◄►  button to adjust the display contrast. 
Sharpness Press the cursor ◄► button to adjust the display sharpness level. 
Gamma Press the cursor  ◄► button to adjust the gamma correction of the display.  
Press  (Enter) /  ► to enter the Advanced menu. See Advanced Feature on 
page Advanced 23. 
Reset Press  (Enter) /  ► to reset all settings to default values. 
 
– 22 –