Planar Pr3010 Projector User Manual

User’s Manual 
– 14 – 
7.  
 
 
8.  
 
When the “Power Off?/Press Power again” 
message appears, press the Power button. 
The projector turns off. 
Turn off the main Power switch when the 
Ready LED stops flashing. 
.  
 
 
Caution: 
Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has 
cooled down.  

DLP® Projector – User’s Manual 
– 15 – 
Setting an Access Password (Security Lock) 
You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the 
projector. When enabled, the password must be entered after you power on the projector. (See 
“Navigating the OSD” on page 32 and “Setting the OSD Language” on page 32 for help on using 
OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the...

User’s Manual 
– 16 – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Be sure cables are not in the way or can cause the projector to be knocked over. 
 
 
 
6.  To raise the level of the projector, lift the projector [A] and press the height-adjuster 
button [B].  
The height adjuster drops down [C].  
7.  To lower the level of the...

DLP® Projector – User’s Manual 
– 17 – 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom 
control (on the projector 
only) to resize the 
projected image and 
screen size.
 
B 
2.  Use the Image-focus 
control (on the projector 
only) to sharpen the 
projected image 
A. 
 
3.  Press the Keystone button 
on the remote control. 
The keystone control 
appears on the display.  
 
4.  Use the Keystone button 
to correct image 
distortion. 
 
Adjusting the Volume 
1.  Press the Volume +/- 
button...

User’s Manual 
– 18 – 
3.  Press the Mute button to 
turn off the volume. (For 
remote only) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

DLP® Projector – User’s Manual 
– 19 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the 
remote control and on the projector. 


                
1.  To open the OSD, press the Menu button....

User’s Manual 
– 20 – 
Setting the OSD Language 
You may want to reference the OSD on your projector while reading this section. Set the OSD 
language to your preference before continuing. (The default language is English.) 
1. Press the Menu button. The Main menu appears. 
 
2. Press the cursor  button until Tool is highlighted.  
 
3. Press the cursor  button until Tool is highlighted.  
4. Press the 
 button until your language is displayed. 
5. Press the Menu button twice to close the OSD....

DLP® Projector – User’s Manual 
– 21 – 
Setting the OSD Language 
Use the following illustration to quickly find a setting or determine the range for a setting.  
  

User’s Manual 
– 22 – 
Main Menu  
Press the Menu button to open the OSD menu. Press the cursor  button to move to the Main 
menu. Press the cursor 
 button to move up and down in the Main menu. Press  to change 
values for settings, and then press Enter or 
 to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT 
Brightness  Press the cursor  button to adjust the brightness. (Range: 0 – 100)  50 
Contrast  Press the cursor  button to adjust the contrast. (Range: 0 – 100)  50 
Sharpness  Press the...

DLP® Projector – User’s Manual 
– 23 – 
Main Menu Functions Available for Connected Source 
Function RGB DVI Component VideoComposite Video S-video 
Brightness x x  x  x  x 
Contrast x x  x  x  x 
Sharpness x x  x  x  x 
Color Temp x x  x  x  x 
Color Saturation    x  x  x 
Color Tint    x  x  x 
Gamma x x  x  x  x 
Color Space x x  x  x  x 
Reset x x  x  x  x 
x = available to video source