Planar Pr2020 Projector User Manual

DLP® Projector – User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
 
Item Label Description See page:
1.   (POWER) Turns the projector On or Off  11 
2.  SOURCE 
Detects the input device 10 
3.  AUTO  Optimizes image size, position, and resolution 
4.  ▲ (Up cursor) / 
KEYSTONE  Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
5.  ►
 (Right cursor) / VOL.  Navigates and changes settings in the OSD 
Quick Menu – For Volume 
18 
On 
System over temperature 
6.  OVER...

DLP® Projector – User’s Manual 
Rear view 
 
 
Item Label Description See page: 
1.  AC IN  Connect the power cable 11 
2.   (USB) Connect the USB cable from a computer  
(service only) 
3.  S-video 
Connect the S-Video cable from a video device 
4.  Video Connect the video cable from a video device  
5.  Audio-in Connect the audio cable from the input device  
6.  RGB  Connect the RGB cable from a computer and 
components 
10 
7.   (Security Lock) Secure to permanent object with a Kensington® 
Lock...

DLP® Projector – User’s Manual 
Bottom view 
 
Item Label Description See page: 
1.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
2.  Tilt adjustor  
Rotate adjuster lever to adjust angle position.  15 
3.  Lamp cover Remove when changing the lamp. 34 
4.  Height adjustor  Adjuster drops down when adjuster button is 
pushed. 
5.  Height adjustor button 
Push to release adjustor. 
15 
 
Note: 
When installing, ensure that you  use only UL Listed...

DLP® Projector – User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with  bright fluorescent lighting turned on. Certain high-frequency fluores-
cent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the  path between the remote control and  the projector. If the path between 
the remote control and the projector is obstructed, you can bounce the signal off certain reflective sur-
faces such as projector screens. 
 
3. The buttons and keys on the...

DLP® Projector – User’s Manual 
— 7 — 
 
Item Label Description See page: 
1.  Up cursor Navigates and changes settings in the OSD  
2.  Enter  Changes settings in the OSD 
18 
3.  Power Turns the projector On or Off 11 
4.  Right cursor Navigates and changes settings in the OSD 18 
5.  Volume +  Increase volume 
6.  Volume -  Decrease volume 
17 
7.  Mute  Mutes the built-in speaker 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device 10 
10.  Auto  Auto adjustment for...

DLP® Projector – User’s Manual 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radius of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the  projector does not respond to the remote control, 
move a little closer....

 – 9  –
 
Setup and Operation 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the di-
rection of the arrow (A). Pull out the 
cover (B). 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the battery when not usi ng the projector for prolonged periods. 
 
 
 
  

DLP® Projector – User’s Manual 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS  players, as well as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to confirm it has  the appropriate output connector.  
 
Item Label Description 
A 
 (USB) Connect the USB cable from a 
computer (service only). 
B 
S-video Connect the S-video cable from a video...

DLP® Projector – User’s Manual 
– 11  – 
Starting and Shutting down the Projector 
1.  Connect the power cord to the pro-
jector. Connect the other end to a 
wall outlet. 
The 
 POWER  and READY  LEDs 
on the projector light. 
2.  Turn on the connected devices.  
3.  Ensure the READY LED displays a 
solid orange and not a flashing or-
ange. Then press the 
  POWER  
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are de-
tected. 
 
See Setting an Access...

DLP® Projector – User’s Manual 
– 12 – 
5.  When the “Power Off? /Press 
Power again” message appears, 
press the POWER button. The pro-
jector turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the READY  LED stops flashing–indicating the projector has 
cooled down.