Planar Pr2010 Projector User Manual

							DLP® Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projec-
tor. When enabled, the password must be enter ed after you power on the projector. (See Navigating 
the OSD  on page  18 and Setting the OSD Language  on page 19 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact your rese ller for information on clearing the password. 
 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move 
to the Installation I  menu. 
 
3.  Press the cursor ▲▼ button to select  
Security Lock. 
4.  Press the cursor  ◄► button to enable 
or disable security lock function. 
A password dialog box automatically  
appears. 
 
–  13  –  
						

							DLP® Projector – User’s Manual 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
Press the cursor buttons in any order 
to set the password. Push the MENU 
button  to exit the  dialog box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the  Security Lock is enabled. 
Enter the password in the order you 
set it at step 5. In case you forget the 
password, please contact the service 
center.  
Service center will validate the owner 
and help reset the password.  
 
 
– 14 –  
						

							DLP® Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
•  Position the projector so that it is perpendicular to the screen. 
•  Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, lift the projector  [A] and press the height-adjuster 
button [B] .  
The height adjuster drops down  [C].  
2.  To lower the level of the projector, press the height-adjuster button an\
d push down on 
the top of the projector. 
3.  To adjust the angle of the picture, turn the tilt-adjuster  [D] right or left until the 
desired angle has been achieved. 
 
–  15  –  
						

							DLP® Projector – User’s Manual 
Adjusting the Focus and Keystone 
1.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image. 
 
2.  Use the KEYSTONE 
buttons (on the projec-
tor or the remote 
control) to correct im-
age-trapezoid (wider 
top or bottom)  
effect. 
 
Remote control and OSD panel 
 
3.  The keystone control  
appears on the display. 
 
 
– 16 –  
						

							DLP® Projector – User’s Manual 
Adjusting the Volume 
1.  Press the Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  Left or Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/-.  
 
 
 
 
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
–  17  –  
						

							DLP® Projector – User’s Manual 
– 18 – 
On-Screen Display (OSD) Menu Settings 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illust ration shows the corresponding buttons on the re-
mote control and on the projector. 
 
 
 
1.  To enter the OSD, press the  MENU button.  
2.  There are five menus. Press  the cursor  ◄► button to 
move through the menus.  
3.  Press the cursor  ▲▼ button 
to move up and down in a 
menu.  
4. Press  ◄► to change values 
for settings. 
5. Press  MENU to close the 
OSD or leave a submenu. 
Note: 
Depending on the video source, not all items in  the OSD are available. For example, the Horizon-
tal/Vertical Position  items in the Computer menu can only be modified when connected to a PC. 
Items that are not available c annot be accessed and are grayed out.   
						

							DLP® Projector – User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2. Press the cursor ▲▼  button until Language is highlighted.  
 
3. Press the cursor ◄►  button until the language you want is highlighted.  
4. Press the MENU button twice to close the OSD.   
– 19  –  
						

							DLP® Projector – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
 
– 20 –  
						

							DLP® Projector – User’s Manual 
OSD Sub-Menu Overview 
 
– 21  –  
						

							DLP® Projector – User’s Manual 
Image Menu  
Press the MENU button to open the OSD menu. Press the cursor  ◄► button to move to the  Image 
Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
values for settings. 
 
Item Description 
Display Mode  Press the cursor ◄► button to set the Display Mode.  
Brilliant Color  Press the cursor ◄► button to adjust the Brilliant Color value. 
Brightness Press the cursor ◄► button to adjust the display brightness. 
Contrast  Press the cursor ◄►  button to adjust the display contrast. 
Sharpness Press the cursor ◄► button to adjust the display sharpness level. 
Gamma  Press the cursor ◄► button to adjust the gamma correction of the display.  
Advanced  Press  (Enter) / 
► to enter the Advanced menu. See Advanced Feature  on 
page 23. 
Reset Press  (Enter) /  ► to reset all settings to default values. 
 
– 22 –