Planar Pd7150 Projector User Manual

Appendix
33
Appendix 

34
Appendix
Maintenance
Cleaning the projector
„Unplug the power cord before cleaning the projector.
„Avoid using benzene or thinners, as these can damage the finish on the cabinet and operation panel.
„Do not use volatile agents, such as insecticides, on the projector.
„Do not leave rubber or plastic objects in contact with the projector for long periods, as they may damage 
the finish of the projector.
„Wipe off dirt gently with a soft flannel cloth.
„For hard-to-remove dirt, soak a cloth in a neutral...

Appendix
35
About the Lamp
The projector lamp has a life span of approximately 2000 hours. Maintain proper ventilation to 
keep the lamp operating throughout its lifetime. Do not subject the projector to unnecessary 
vibrations to ensure that the lamp does not break.
„It is recommended that the lamp (sold separately) be replaced after approximately 2,000 cumulative hours 
of use or when you notice a significant deterioration in the picture and color quality. The number of hours 
the lamp has been used...

36
Appendix
Removing and Replacing the Lamp
Follow these instructions to replace the lamp.
•  
Remove the lamp unit by the handle. Do not to touch the glass surface of the lamp unit or the inside of the 
projector.
•  To avoid injuring yourself and damaging the lamp, carefully follow the steps below.
•  Only loosen the screws for the lamp unit cover and lamp unit. 
(Only the silver screws are loosened).
1. If the projector is running, press   on the projector or   on the remote control to 
turn off the...

Appendix
37
4. Remove the lamp unit.
•  
Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction 
of the arrow.
   
5. Insert the new lamp unit.
•  
Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
•  Attach the lamp unit cover.
•  Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. 
•  Tighten the cover screw.
 Info
•  
If the lamp unit and lamp cover are not...

38
Appendix
Connecting Pin Assignments
DVI-D port: 25 pin connector
•  VI Digital INPUT
RS-232C Port: 9-pin D-sub Female connector of the DIN-D-sub RS-232Cvt cable 
pin connector
   
Pin No. Signal Pin No. Signal
1 T.M.D.S data 2- 16 Hot plug detection
2 T.M.D.S data 2+ 17 T.M.D.S data 0–
3 T.M.D.S data 2 shield 18 T.M.D.S data 0+
4 Not connected 19 T.M.D.S data 0 shield
5 Not connected 20 Not connected
6 DDC clock 21 Not connected
7 DDC data 22 T.M.D.S clock shield
8 Not connected 23 T.M.D.S clock+
9...

Appendix
39
Computer Compatibility Chart
Computer
•  Multiple signal support
Horizontal Frequency: 25–75 kHz, Vertical Frequency: 50–85 Hz, Pixel Clock: 25–108 MHz
•  Compatible with sync on green and composite sync signals
•  XGA compatible with advanced intelligent compression
The following is a list of modes that conform to VESA. However, this projector supports 
other signals that are not VESA standards.
PC/
MAC/
WSResolutionHorizontal 
Frequency 
(kHz)Ve r t i c a l  
Frequency 
(kHz)VESA...

40
Appendix
Video Compatibility Chart
1. Component 1/2 support signal formats are Y/Pb/Pr, Y/Cb/Cr
2. VGA port support signal formats are RGsyncB, RGBHV or RGBCsysc
3. “U” means manual setting is needed
DTV
ResolutionH-Freq 
(kHz)V-Freq    
(Hz)Comp1    
SupportComp2 
SupportS-Video 
SupportCompos-
ite SupportVGA
SupportDVI
Support
SD Video NTSC 640x480i 15.73 59.94/603333
PAL 768x576i 15.63 503333
SECAM 768x576i 15.63 503333
NTSC-4.43UUUU
PA L - MUUUU
PA L - NUUUU
NTSC-JUUUU
PAL-60UUUU
NTSC-50
ED TV...

Appendix
41
Troubleshooting
Problem Check
Projector does not startProjector power cord is not plugged into the wall outlet.
Remote control batteries have run out.
No pictureThe selected input mode is wrong.
Cables may be incorrectly connected to the rear panel of the projector.
Power to the external connected device is off.
The video signal format of the video equipment is not set correctly.
Color is fadedPicture adjustments are incorrectly set.
Picture is blurredFocus is incorrectly set.
The projection...

42
Appendix
Product Specifications
Item Description
Model No. PD7130/PD7150 DLP Front Projector
DLP Panel
Display method: PD7130→0.65” WXGA, DC3. 
                           PD7150→ 0.8” HD2 + DC3
Device method: Digital Light Processing (DLP
®)
Display Type DLP Chip, RGB optical shutter method
Resolution 1280 x 720 pixels
Lens 7130: F2.4~2.5, f=19.1~23.9
7150: F2.36~2.5, f=24.0~30.1
Projection Lamp 250 W / 200 W switchable UHP lamp
Input Sources Video VGA
YCbCr, YPbPr1, 2
CVBS (Composite Video)
S-Video...