Planar Pd7060 Projector User Manual

							31
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
Planar recommends changing the projection lamp after a warning message displays Warning: 
Lamp life time Over. It should only be replaced with a certifi ed replacement part, which you can 
order from your local dealer.
                      
Important!
The lamp contains a certain amount of mercury and should be disposed of 
according to local ordinance regulations.
Avoid touching the glass surface of the new lamp: Doing so may shorten 
its operation life. 1.
2.
Be sure to turn off and unplug the projector at least an hour before replacing 
the lamp. Failure to do so could result in a severe burn. 
1.Loosen the screw on the lamp 
compartment cover.
2.Open the lamp compartment 
cover. 
						

							32
3.Remove the three screws from 
the lamp module.
4.Lift the module handle up.
5. Pull fi rmly on the module 
handle to remove the lamp 
module.
6. Reverse steps 1 to 5 to install 
the new lamp module. 
						

							33
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.Press the Menu button to open the OSD 
menu.
2. Press the cursor ◄ ► button to move to 
the Service menu.
3. Press the cursor ▲▼ button to move 
down to Lamp Hour Reset.
4. Press the cursor ◄ ► or Enter button. 
A message screen appears.
5. Press the cursor buttons in this order: 
▼ ▲ ◄  ►.
The Status menu appears again showing 
the Lamp Hours reset to zero.
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation. 
Be sure to turn off and unplug the projector at least an hour before clean-
ing. Failure to do so could result in a severe burn.
Use only a dampened cloth when cleaning. Do not allow water to enter the 
ventilation openings on the projector. 
If a little water gets into the projector interior while cleaning, leave un-
plugged in a well-ventilated room for several hours before using.
If a lot of water gets into the projector interior when cleaning, have the pro-
jector serviced.  1.
2.
3.
4.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the 
projector lens.
Apply a little optic lens cleaner to a clean soft cloth. 
(Do not apply the cleaner directly to the lens.)
Lightly wipe the lens in a circular motion.
CAUTIONCAUTION
Do not use abrasive cleaners or solvents.
To prevent discoloration or fading, avoid getting cleaner on the projector 
case. 1.
2.
1.
2. 
						

							34
Using the Kensington® Lock
If you are concerned about security, attach one end of a security cable to a permanent object and 
the other to the Kensington slot and a projector. 
Contact your vendor for details on purchasing a suitable Kensington security 
cable.  The security lock corresponds to Kensington’s MicroSaver Security 
System. If you have any comment, contact: Kensington, 2853 Campus Drive, 
San Mateo, CA94403, U.S.A. Tel: 800-535-4242, 
http://www.Kensington.com. 
						

							35
TROUBLESHOOTING
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose 
connection. Check the following before proceeding to the problem-specifi c solutions.
Use some other electrical device to confi rm that the electrical outlet is working.
Ensure the projector is turned on.
Ensure all connections are securely attached. 
Ensure the attached device is turned on.
Ensure a connected PC is not in suspend mode.
Ensure a connected notebook computer is confi gured for an external display. (This is 
usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specifi c section, try the steps in the order suggested. This may help you to solve 
the problem more quickly.
Try to pinpoint the problem and thus avoid replacing non-defective parts. 
For example, if you replace batteries and the problem remains, put the original batteries back and 
go to the next step. 
Keep a record of the steps you take when troubleshooting: The information may be useful when 
calling for technical support or for passing on to service personnel.•
•
•
•
•
• 
						

							36
LED Error Messages
Before cooling, the LED will blink three (3) times in two (2) second intervals. The LED message is 
defi ned by the blinking sequence. A long blink is defi ned as 1 second.  A short blink is defi ned as 
0.3 seconds. The LED messages are listed below:
ERROR CODE MESSAGELED FLASH
Environment Over Temperature 1 long blink / 1 short blink
DMD Over Temperature  1 long blink / 2 short blinks
Lamp Over Temperature 1 long blink / 3 short blinks
Fan1 Locked
1 long blink / 4 short blinks
Fan2 Locked
2 long blinks / 2 short blinks
Fan3 Locked
2 long blinks / 3 short blinks
Fan4 Locked 2 long blinks / 4 short blinks
DMD Initial Fail 3 long blinks / 1 short blink
Lamp Initial Fail 3 long blinks / 2 short blinks
Ballast UART Error 3 long blinks / 3 short blinks
Temperature Sensor Fail 3 long blinks / 4 short blinks
Inter Lock Open 4 long blinks / 1 short blink 
						

							37
Common Problems and Solutions
This section describes some common problems and their solutions.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred 
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 7-meter (23-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect) 
1. Position the projector so it is as perpendicular to the screen as possible. 
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed or upside down
Check the Projection setting on the Utility menu of the OSD.
Problem: The image is streaked 
1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default 
settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer. 
Problem: The image is fl at with no contrast 
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
Lamp Problems
Problem: There is no light from the projector 
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections. 
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the 
projector. When the Power LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced. 
						

							38
Remote Control Problems
Problem: The projector does not respond to the remote control 
1. Direct the remote control towards remote sensor on the projector. 
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced. 
						

							39
SPECIFICATIONS
Hardware Specifi cations
MODELPD4010 PD7010 PD7060
Display typeTI DMD 0.55-inch x 1, 12 
degrees, DDR DMD with 
DDP2000TI DMD 0.65-inch x 1, 12 
degrees, LVDS DMD with 
DDP3020TI DMD 0.65-inch x 1, 12 
degrees, LVDS DMD with 
DDP3020
Resolution 480p (854x480) 720p (1280x720) 720p (1280x720)
Color 16.7 Million (24-bits/pixel)
Weight 4kg / 8.8lbs
Projection 
distance1.5 to 7 meters (59 to 275 inches)
Projection screen 
size0.76 to 3.81 meters (30 to 
150 inches)0.88 to 4.45 meters (35 to 
175 inches)0.88 to 4.45 meters (35 to 
175 inches)
Projection lens Manual zoom; manual focus
Zoom ratio 1.16:1
Horizontal 
keystone 
correctionN/A +/- 40 degrees +/- 40 degrees
Vertical
keystone 
correction+/- 15 degrees
Projection
methodsDesktop front/rear; ceiling front/rear
Data 
compatibilityIBM PC or compatibles 
(VGA, SVGA, XGA), MacIBM PC or compatibles 
(VGA, SVGA, XGA, 
SXGA), MacIBM PC or compatibles 
(VGA, SVGA, XGA, 
SXGA), Mac
SDTV/EDTV/
HDTV480i, 576i/480p, 
576p/720p, 1080i480i, 576i/480p, 
576p/720p, 1080i, 1080p480i, 576i/480p, 
576p/720p, 1080i, 1080p
Video 
compatibilityNTSC/NTSC 4.43, PAL (B/G/H/I/M/N 60), SECAM
H-Sync 15,31 - 70 kHz 15,31 - 90 kHz 15,31 - 90 kHz
V-Sync 50 - 85 Hz 50 - 85 Hz 50 - 85 Hz
Safety 
certifi cationFCC-B, UL, c-UL, TUV-GS, CB, CE, CCC, ICES-003 (class B), C-Tick, NOM, WEEE, 
RoHS, PCT, MIC/EK
Operation
temperature10° C ~ 35° C
Dimensions See “Projector Dimensions” on page 44
Power
consumptionTypical 255W (normal mode); Typical 230W (Eco mode)
Stand By < 1 watt
Lamp Boost mode: 230W; normal mode: 200W; Eco mode: 180W 
						

							40
Input/output Connectors
MODELPD4010 PD7010 PD7060
PC RGB RGB RGB /DVI-D
VideoComposite video (RCAx1)
Mini-jack to S-Video (Mini-DIN)
Component (RCA x3)
DVI-D (HDCP)
None HDMI (HDCP) HDMI (HDCP)
Security Kensington slot