Philips Velo 1 Manual

							11
To install the Windows CE 2.0 ROM Miniature Card
1Back up all files on your Velo 1 as described above.
2Turn off your Velo 1.
3On the bottom of your Velo 1, slide back the latch to
release the door to the Flash/ROM Miniature Card slot and
remove the door to the slot and the dummy card or Flash
Card.
4Insert the ROM Miniature Card into the slot, and push the
card down until it snaps into place.
5Replace the door.
Step 1: Set Up Your Velo 1 for the Upgrade 
						

							12
Philips Velo™1 User’s Guide
Note:Do not remove the Windows CE 2.0 ROM Miniature Card
from the Flash/ROM Miniature Card slot. After you install the ROM
Miniature Card, you will be unable to use the Flash/ROM Miniature
Card slot for other cards, such as flash memory upgrades or programs
that come on Miniature Cards.
1d: Install more RAM in your Velo 1.
If you do not have 12 MB of RAM installed on your Velo 1 you
will need to install enough RAM to bring your device up to 12
MB in order to proceed with the upgrade.
1Take your Velo 1 out of the Velo Dock.
2Remove the screw from the DRAM Miniature Card slot
and remove the slot door.
3If there is a card (or a plastic dummy card) already in the
slot, remove it.
4Insert the 8 MB DRAM Miniature Card in the slot by
pushing down the card until it snaps into position.
5Replace the door and the screw.
1e: Follow the steps below and reinsert the
main battery (or batteries) and the backup
battery.
1Plug the supplied AC adapter into your Velo 1 and a wall
outlet.
2Press the Power button to turn on the Velo 1.
3The Welcome Wizard appears; ignore it for now.
4 Unplug the AC adapter from the Velo 1.
5Insert the main battery and the backup battery. (See the
figures on page14.)
6 Plug the AC adapter into the Velo 1.
7Press the Power button to turn on the Velo 1.
8Tap 
 to close the Expansion Memory Detected dialog
window.
After you reinsert the batteries, go to “Step 2: Install Windows CE
Services 2.0 on Your Desktop Computer” on page 15. 
						

							13
Step 1: If you purchased the Velo 1 with 12 MB
of DRAM and the Microsoft Windows CE 2.0
Upgrade Card already installed, start here:
1Plug the supplied AC adapter into your Velo 1 and a wall
outlet.
2Press the Power button to turn on the Velo 1.
3The Setup Wizard appears; ignore it for now.
4 Unplug the AC adapter from the Velo 1.
5Insert the main battery and activate the backup battery.
(See the figures on the next page.)
aSlide the main battery door lock.
bOpen and detach the battery door.
cPull out the yellow plastic tab and discard it.
(This step activates the backup battery.)
dInsert the NiMH rechargeable battery pack.
eReplace the battery door.
6 Plug the AC adapter into the Velo 1.
7Press the Power button to turn on the Velo 1.
8Tap 
 to close the Expansion Memory Detected dialog
window.
Step 1: Set Up Your Velo 1 for the Upgrade 
						

							14
Philips Velo™1 User’s Guide
Bottom of Velo 1
-
+
Bottom view showing rechargeable battery pack insertion 
						

							15
Step 2: Install Windows CE Services 2.0
On Your Desktop Computer
System requirements
The minimum PC requirements for running Windows CE Services 2.0
are as follows:
wMicrosoft Windows NT
® Workstation 4.0 or Windows 95
wDesktop computer with a 486/33DX or higher processor
(Pentium P90 recommended)
w12 MB of memory for Windows NT Workstation 4.0
w8 MB of memory (12 MB recommended) for Windows 95
wHard disk drive with 10 to 50 MB of available hard-disk
space (actual requirements will vary, based on selection of
features and current system configuration)
wAvailable 9- or 25-pin communications port (25-pin port
requires adapter)
wCD-ROM drive
wVGA or higher-resolution graphics card (Super VGA
256-color recommended)
wKeyboard
wMicrosoft Mouse or compatible pointing device
In addition, the following optional system components will allow
you to use certain features of Windows CE Services:
wAudio card and speakers for sound
wMicrosoft Office 97 or Microsoft Office 95
wSerial or built-in infrared adapter for synchronization
wModem for remote synchronization
wEthernet LAN connection for remote synchronization
Step 2: Install Windows CE Services 
						

							16
Philips Velo™1 User’s Guide
In addition to Windows CE Services 2.0, the Microsoft Windows CE
compact disc contains Microsoft Schedule+, updates to the Windows
Messaging System (Microsoft Exchange), and Windows 95 Dial-Up
Networking and some optional items. The installation program will
check for and install these components as necessary to ensure that
you can set up and run Windows CE Services 2.0, as well as
applications including Pocket PowerPoint
® and Pocket Streets.
Installing Windows CE Services 2.0
The Windows CE Services 2.0 installation program includes several
steps. The steps you follow depend on your operating system
(Windows 95 or NT) and system configuration. When you run Setup,
it tests for installed components and prompts you to install only
those components you need. To ensure that you install all the
necessary components, simply click each button in order on the
Setup screen. You may be instructed to restart your computer
several times during the installation procedure.
To install Windows CE services on your desktop computer, follow
these steps:
1Insert the Microsoft Windows CE compact disc in a CD-ROM
drive on your desktop computer.
Setup begins automatically. If Setup does not begin
automatically, click Run on the Start menu, then type d:setup
(where d: is the letter of the drive containing the Microsoft
Windows CE CD) and press Enter.
2Follow the instructions on your screen to complete installation.
3When the “Get Connected” dialog box appears, click Cancel.
Proceed to Step 3 on page 17. 
						

							17
Step 3:  Prepare Your Velo 1 and Your
Desktop Computer for Velo 1 Application
Installation
Before you install Velo 1 applications, you must set the PC
connection on your Velo 1. Instructions for setting the connection
are below.
If you are an experienced user, you may want to set up your
Velo 1 and your computer to make the installation procedure go
much more quickly. Making these changes requires many more
steps, but greatly speeds up the installation process. If you choose
to make these changes, skip the instructions below (“To set the PC
connection on your Velo 1”) and follow the instructions on the next
page, “To increase the speed of data transfer between your Velo 1
and desktop computer.”
To set the PC Connection on your Velo 1
1Make sure your Velo 1 is turned on.
2Tap Start in the lower left-hand corner, tap Settings, then
tap Control Panel.
3Double-tap Communications.
4Tap the PC Connection tab.
5Tap the Change button.
6Under Connect to desktop computer using, select
Desktop @ 19200.
Important:   Even though Desktop @ 19200 is the default setting,
you still need to select it to make it active.
7Tap 
 to close the PC Connection dialog box.
8Tap 
 to save the Communications settings.
9Go to “Step 4: Install Velo Applications From the Velo 1
Upgrade CD” on page 20.
Step 3: Prepare for Velo 1 Application Installation 
						

							18
Philips Velo™1 User’s Guide
To increase the speed of data transfer between your
Velo 1 and desktop computer
1Disconnect the Velo 1 from the desktop computer.
2On the Velo 1, tap Start, tap Programs, tap
Communication, then tap Remote Networking.
3Double-tap Make New Connection.
4Under Type a name for the connection, type a name
(such as “Fastest”), then tap Next.
5Tap Configure, and then in the Baud Rate list, select the
desired rate (typically 115,200 baud is the fastest), then
tap 
.
6Tap Finish. Tap x to close the window.
7Tap the Start menu, tap Settings, then tap Control
Panel.
8Double-tap Communications.
9Select the PC Connection tab, then tap Change.
10Under Connect to desktop computer using, select
the connection you created above.
11Tap 
, then tap  again to close the Communications
control panel. Tap x to close the window.
12Reset your Velo 1 (tap Start, tap Run, type reset, then
tap 
). In the Reset Velo 1 dialog box, tap Ye s.
13On your desktop computer, open the Mobile Devices
window. In the File menu, click Communications, clear
Enable mobile device connection and click Apply.
14If you are using Windows 95, go to step 15. If you are using
Windows NT, go to step 16 on the next page. 
						

							19
Step 3: Prepare for Velo 1 Application Installation
15If you are using Windows 95:
aOn your desktop computer, click Start, point to
Settings, click Control Panel, then double-click the
System icon.
bClick the Device Manager tab, double-click Modem,
then select the port to which your Velo 1 is connected.
cClick Properties, click the Modem tab, and then under
Maximum speed select the same rate you specified on
your Velo 1. Tap 
 to close the window.
dClick OK, then click OK again to close the System
Properties dialog box. Tap 
 to close the window.
eGo to step 17 below.
16
If you are using Windows NT:
aOn your desktop computer, click Start, point to
Settings, then click Control Panel.
bDouble-click the Modems icon.
cSelect Dial-Up Networking Serial Cable between 2
PCs, then click Properties.
dSet the Maximum speed to the same rate you
specified on your Velo 1, click OK, then click Close.
eGo to step 17 below.
17In the Mobile Devices window, open the File menu, click
Communications, select Enable mobile device
connection, and click Apply.
18Close all desktop programs and restart your computer. 
						

							20
Philips Velo™1 User’s Guide
Step 4: Install Velo 1 Applications From
the 
Velo 1 Upgrade CD
The Philips Velo 1 Upgrade compact disc includes programs and
components of the Velo 1 applications and operating system. You
must install these components to ensure that all features of your
Velo 1 will function as intended. To install these programs from
the CD, follow these steps:
1Connect the Velo Dock’s cable to the desktop computer’s
serial port.
2Plug the AC power adapter into the DC jack on your Velo
Dock.
3Place your Velo 1 in the Velo Dock and firmly slide the
H/PC until it snaps into place and the green light comes
on. Open the lid of the Velo 1 and make sure it is on.
4In My Computer (on your desktop computer), browse to
the Mobile Devices folder and double-click the Velo 1
icon to start Windows CE Services 2.0.
Note:The first time you connect your Velo 1, Windows CE Services
2.0 may prompt you to select a communications port. Select the port
to which your Velo Dock or serial cable is connected, and make sure
the port speed is set to the speed you set your Velo 1 to in “Step 3:
Prepare Your Velo 1 and Your Desktop Computer for Velo 1 Application
Installation.”