Philips Respironics User Manual

9
Menu Navigation (Therapy ON) and Optional Humidification Settings
While the device is delivering therapy, you can adjust Tube Temperature or Humidifier Settings. Rotate the control dial 
to choose either setting. Press and rotate the dial to change the setting.
Note: If you are using the Humidifier without the Heated Tube, simply just rotate the control dial to change the 
Humidifier setting.
Therapy Pressure Screen
#FeatureDescription
1Therapy PressureDisplays the current delivered pressure....

10
Menu Navigation (Therapy OFF)
From the Home screen, you can scroll between the following four options: 
          My Info          Preheat    My Provider   My Setup
My Info: This menu provides summary statistics of your therapy use.
Preheat: This function lets you warm up your humidifier for 30 minutes before starting a therapy session.
My Provider: This menu contains information that your provider may direct you to read to them so they can 
better assist you over the phone.
My Setup: This menu...

11
Preheat:
  
Preheat On Screen Preheat Off Screen
When using a humidifier, the device can preheat the water tank for up to 30 minutes prior to starting therapy.
In order to activate the preheat mode, the blower must be “off ” and a humidifier must be attached. When “Preheat” 
is selected, you will be able to turn the control dial to choose between “on” or “off ”. Press the control dial again to 
make your selection. During the 30 minute preheat, you will still be able to use the control dial to select...

12
IconTextDescription
UploadAllows user to initiate a modem call when an optional Cellular Modem or Wi-Fi 
Accessory is installed. Signal strength is indicated at the top right of this screen. 
After the modem upload has finished, the screen will either display a green 
checkmark with the text “Completed” to indicate a successful upload, or a red X 
with the text “Failed” to indicate an unsuccessful upload. If the upload fails, initiate 
an upload a second time, or contact your home care provider if the...

13
IconTextDescription
Mask TypeThis setting allows you to adjust the level of air pressure relief based on the 
specific Philips Respironics mask. Each Philips Respironics mask may have a 
“System One” resistance control setting. Contact your home care provider if 
you cannot find this resistance setting for your mask.
Note: If a lock icon  is displayed on this screen, it indicates that your 
provider has locked this setting and you cannot change it.
Tube TypeThis setting allows you to select the...

14
Bluetooth Wireless Technology
Your device has Bluetooth wireless technology. which is one method by which you can transfer your therapy device’s 
data to DreamMapper. DreamMapper is a mobile and web-based system designed to help Obstructive Sleep Apnea 
(OSA) patients enhance their sleep therapy experience.
Pairing your therapy device to your Bluetooth enabled Mobile Device
   Note: You can only pair your therapy device to one mobile device at any given\
 time.
   Note: Pairing works best when your...

15
Check Mask Fit
The optional check mask fit feature can be enabled or disabled by your home care provider. This feature allows you to 
check the fit of your mask prior to starting therapy. This is done by measuring the amount of leak. Put on your mask 
assembly. Refer to your mask instructions if needed. Navigate to the Check Mask Fit screen under “My Setup” and 
press the control dial to initiate the check. 
The device will deliver a test pressure while the screen counts down 40 seconds. A green bar...

16
Device Alerts
Device alerts are pop-ups that show up on the UI screen. There are 5 types of alerts described here:
•  Status: These alerts are just the pop-up screen. 
•  Notification: These alerts consist of the pop-up screen in addition to a blinking Power LED on top of the device.
•  Alert 1: These alerts consist of the pop-up screen, a blinking Power LED and an audible beep when displayed. This 
alert will not occur during therapy.
•  Alert 2: These alerts consist of the pop-up screen, a blinking...

17
AlertIconTypeDescriptionPossible CauseAction
SD Card 
Removed.
Notification
or Alert  2
Indicates SD card 
has been removed 
from therapy device 
and not reinserted 
before the start of 
the current therapy 
session.
SD card was not 
reinserted into device.
Reinsert SD card, or 
click to clear alert.  
Oximetry: Good 
Study 
(icon only)
NotificationNotifies that user has 
a achieved at least 4 
hours of therapy and 
oximetry  use. Appears 
at the end of therapy.
n/aPress Control Dial 
to acknowledge...

18
AlertIconTypeDescriptionPossible CauseAction
Heated Tube 
Error. Contact 
support if the 
problem persists.
StatusHeated tube error 
(only when heated 
tube is present)
Heated tube may 
be overheated or 
damaged.
Turn off device.  
Detach heated tube 
from humidifier, 
make sure that tube 
is not covered or 
obstructed, and then 
reattach to humidifier. 
If alert continues, 
contact your provider.
The attached 
power supply 
does not support 
humidification.
Alert 2Indicates that the 
attached power...