Philips Proscreen Pxg30 Inpact Projector User Manual

							21
7.OperationAdjusting the Screen
Adjusting the Screen
The message disappears after 4 seconds.
The message disappears after 4 seconds.
Zoom Adjustment
Focus Adjustment
Press zoom – / +button to adjust the image.
Keystone Adjustment
Press D-keystbutton on the remote control or select
Keystone on Setting menu.  (Refer to page 36.)  Keystone
dialog box appears.
Correct the keystone distortion by pressing Cursor
Up/Down/Left/Rightbutton(s).  Press Cursor Upbutton to
reduce the upper part of the image, and press Cursor Down
button to reduce the lower part.  Press Cursor Leftbutton to
reduce the left part, and press Cursor Rightbutton to reduce
the right part.  
If a projected picture has keystone distortion, correct the image
with Keystone adjustment.
–The arrows are white in no correction.
– The arrow(s) of direction being corrected
turn(s) orange.
– The arrow(s) disappear(s) at the maximum
correction.
– If you press resetbutton on the remote
control while the keystone dialog box is
being displayed, the keystone adjustment
will be canceled.
Lens Shift Adjustment
Note:
Focus adjustment may not function properly if the image is
corrected by Keystone adjustment.
Reduce the upper width
with Cursor Upbutton. Reduce the lower width with
Cursor Downbutton.  Reduce the left part with
Cursor Leftbutton.  Reduce the right part with
Cursor Right button.  
1
2
– Top Control
Press Lensbutton and select Zoomfunction. Press Cursor
Up/Downto adjust the image
– Remote Control
– Top Control
Press Lensbutton and select Focusfunction. Press Cursor
Up/Downto adjust the focus of the image.
Press focus – / +button to adjust the focus of the image.
– Remote Control
Press lens shift – / +button to move up / down the image.
– Top Control
Press Lensbutton and select Lens shiftfunction. Press Cursor
Up/Downto move up / down the image.
– Remote Control 
						

							22
Adjusting the Screen
Sound Adjustment
7.Operation
Press D-freezebutton on the remote control to capture a moving
picture.  To cancel, press D-freezebutton once again or press any
other button.
Press AV Mutebutton on the top control or the remote control to
black out the image and to mute the sound .  To restore to normal,
press AV Mutebutton again or press any other button.
A/V Mute Function Picture Freeze Function
Message disappears after 4 seconds.
Presstimer button on the remote control.  The timer display
“00 : 00” appears on the screen and the timer starts to count time
(00 : 00 ~ 59 : 59).  
To stop the timer display, press timerbutton.  Press again to
cancel this function.
SmartTimer Function
Press Menubutton to display the On-Screen Menu. Press
Cursor Left/Rightbuttons to select Sound Menuicon.  –
Volume
Press Volume + / – button(s) on the top control or on the remote
control to adjust volume.  Volume dialog box appears on the
screen for a few seconds.
+button for increasing volume, and –button for decreasing.
–
Mute
Press Mutebutton on the remote control to mute the sound.  To
restore sound to its previous level, press Mutebutton again or
press Volume + / –button(s).
To increase volume, press Cursor Rightbutton, and press Cursor
Leftbutton to decrease volume. 
Press Cursor Left/Rightbutton(s) to mute the sound.  Dialog box
display is changed to “On” and sound is muted.  To restore sound
to its previous level, press Cursor Left/Rightbutton(s) again.
Press Cursor Downbutton to select the item to be adjusted,
and then press OKbutton.
Indicates approximate
level of volume.
Close Sound Menu.
Sound Adjustment
Direct Operation
Menu Operation
Volume
Mute
Indicates approximate
level of volume.
Press Mutebutton to set
Mute function On or Off.
The display disappears after 4 seconds.  
SOUND MENU
Sound Menuicon
1
2 
						

							23
8. Computer InputSelecting Input Source
Selecting Input Source
Menu Operation Direct Operation
Select an Input source by any of the followings:
–Press Databutton on the top control or CH+
button on the
remote control.The button toggles among Data1, Data2 and
Data3.
–Press D1, D2or D3button on the remote control.
If the projector cannot project properly, select a correct input
source following the Menu Operation as shown below.  
Press Menubutton to display the On-Screen Menu.  Press
Cursor Left/Rightbutton to select the Input Menuicon.
Press Cursor Up/Downbutton to select Data 2and then press
OKbutton.  
Data/CH+ button
toggles as follows
Data1
Data 3
Select Data1 and press OK
button.
Select Data orRGB (Scart)
and press OK button.
Source Select Menu
INPUT MENU (Selecting Data 1)
Input Menuicon
When Data 3 in/Data out socket is used as Data 3
in, select Data (In)
When Data 3 in/Data out socket is used as Data
out, select Data (Out)
Data 2
PressMenubutton to display the On-Screen Menu.  Press
Cursor Left/Right button to select the Input Menuicon.
Press Cursor Up/Downbutton to select Data 1and then press
OKbutton.  Source Select Menuwill appear.   
Press Cursor Up/Downbutton select  Data or RGB(Scart)
and press OKbutton.
Select Data(In)or Data(Out)
and press OK button.
Source Select Menu
INPUT MENU (Selecting Data 2)
Data 1 : Data / RGB (Scart)
Input Menuicon
Select Data 2and press
OK button.
When computer output is connected to Data 1 in
socket, select Data.Data
When video equipment is connected to Data 1 in
socket, select RGB (Scart). Refer to page 31.RGB (Scart)
Remote Control
2
3
1
Data 2 : Data
2
1
Data 3 : Data(In) / Data (Out)
PressMenubutton to display the On-Screen Menu.  Press
Cursor Left/Rightbutton to select the Input Menuicon.
Press Cursor Up/Downbutton to select Data 3and then
press OKbutton.  Source Select Menuwill appear.   2
1
Press Cursor Up/Downbutton to select Data (In) or Data
(Out) and press OKbutton.3
Data (In)
Data (Out)
INPUT MENU (Selecting Data 3)
Input Menuicon
Select Data 3and press
OK button.
Note:
Data 3(D3) cannot be selected when Data (Out) is set as Data 3
source. Refer to the Menu Operation below. 
						

							24
Selecting Computer System8. Computer Input
This projector accepts various kinds of computer signals including VGA, SVGA, XGA and SXGA. By selecting a Data input as a
signal source, it automatically detects the signal format and tune itself to project a proper image without any additional
settings. (Signal formats provided in this projector is shown on Page 49.)
When the projector cannot recognize connected signal
as PC system provided in this projector, Auto Image
Adjustment function operates to adjust the projector
and the message “Auto” is displayed on System
Menu icon.  (Refer to page 25.) 
There is no signal input from a computer. Make sure
the computer and the projector are properly connected.
(Refer to Installation on page 15.)
Auto
––––
System Menu icon
Displays system being
selected.
PC SYSTEM MENU
Select Computer System Manually
System Menu icon 
Displays selected system.
The systems on
this dialog box
can be selected.
Press Menubutton to display the On-Screen Menu.  Press
Cursor Left/Right buttons to select PC System Menu icon.
Press Cursor Downbutton to select the system that you want
to set, and then press 
OKbutton.  
PC SYSTEM MENU
Custom Mode(1~5) set in PC
Adjust Menu.  (P26, 27)
PC system can be also selected manually.
Selecting Computer System
2
1
Note:
If the image is not provided properly, manual adjustment may be
required. Refer to the section Manual PC Adjustment.(page 26~27)
Note : The projector may display one of the following messages. 
						

							25
PC Adjustment
Auto Image Adjustment
Auto Image Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer.  This function can be operated as follows.
Press Menubutton to display the On-Screen Menu. Press
Cursor Left/Rightbutton to select PC Adjust Menuicon.
Press Cursor Downbutton to select Auto Imageicon and
then press OKbutton twice.
This Auto Image can be also executed by pressing autobutton
on the remote control.
Select Auto Imageicon and press
OKbutton.
PC ADJUST MENU Auto Image
PC Adjust Menuicon
✽To store  adjusted parameters.
Parameters adjusted with Auto Image function can be store in
this projector.  Once parameters are stored, the setting can be
done just by selecting Mode in PC System Menu (P24).  Refer to
step 3 of Manual PC Adjustment section (P27).
Note:
–Fine sync, Total dots and Picture Position of some computers
can not be fully adjusted with Auto Image function. In this case,
manual adjustments will be required.  (Refer to page 26, 27.)
–Auto Image function cannot be operated when “RGB”, “1035i
(HDTV)”, “1080i (HDTV)” is selected on PC System Menu (P24).
2
1
8. Computer InputPC Adjustment 
						

							26
8. Computer InputPC Adjustment
This projector can automatically tune the display signals from the most of personal computers currently distributed.  However,
some computers employ the special signal formats which may not be tuned by SmartSetof this projector. In this case, the
image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture, and
projected improperly. 
The Manual PC Adjustment function allows you to manually adjust several parameters to match these special signal formats.
Also, you can store these adjusted parameters in the 5 independent memory areas, enabling you to call up whenever you
need. 
Press Menubutton to display the On-Screen Menu.  Press
Cursor Left/Rightbutton to select PC AdjustMenu icon.
Press Cursor Downbutton to select the item to adjust and
then press OKbutton.  Adjustment dialog box will appear.
Press Cursor Left/Rightbutton to adjust the value.
Select the item and 
press OKbutton.
PC ADJUST MENU
PC AdjustMenu icon
Adjusts an image as necessary to eliminate flicker from the
display.  Press Cursor Left/Rightbutton to adjust value.(From 0 to
31.)Fine sync
Adjusts the number of total dots in one horizontal period.  Press
Cursor Left/Rightbutton(s) to adjust the number to match your
PC image.Total dots
Adjusts horizontal picture position.  Press Cursor Left/Right
button(s) to adjust the position.Horizontal
Adjusts vertical picture position.  Press Cursor Left/Right
button(s) to adjust the position.Vertical
Press OKbutton to show the information of the selected
computer .Current mode
Adjusts clamp level.  When the image has a dark bar(s), try this
adjustment.Clamp
Press OKbutton at this icon to adjust
“Clamp,” “Display area (H/V)” or set
“Full screen.”Press Cursor Left/Right
button to adjust the value.Shows status
(Stored / Free) of the
selected Mode. Selected Mode
Press OK button at Current
mode icon to show the
information of the connected
computer 
Current mode
2
1
Manual PC Adjustment 
						

							27
PC Adjustment8. Computer Input
Selects the area displayed by this projector.  Select the resolution
at Display area dialog box.Display area
Adjusts the horizontal area displayed by this projector.  Press
Cursor Left/Rightbutton(s) to decrease/increase value and then
press OKbutton. Display area H
Adjusts the vertical area displayed by this projector.  Press Cursor
Left/Rightbutton(s) to decrease/increase value and then press OK
button.Display area V
Press Cursor Left/Rightbutton(s) to switch Full screen function to
“On” or “Off.”  Set “On” to resize the image with 4 x 3 aspect
ratio to fit the screen.Full screen
Reset
Store
Closes PC Adjust Menu.
Quit
To store adjusted parameters, select Storeicon and press OK
button.  Select any of Mode 1 to 5 that you want to store to
and then press OKbutton.
Resets all the adjusted parameters on adjustment dialog box to
previous figure.
Mode free
Vacant ModeShows values of “Total dots,”
“Horizontal,” “Vertical,”
“Display area H,” and “Display
area V.”
Storeicon
Mode freeiconClose this dialog box.
To store adjustment data
To clear adjustment data
To clear adjusted parameters previously set, select Mode free
icon and press OKbutton.  Select the Mode that you want to
clear and press OKbutton.Display area
Press Cursor Left
/Right button(s) to
adjust value and then
press OKbutton. Press OKbutton at Display area
icon and Display area dialog box
appears.
This Mode has parameters being stored.
Note : Fine sync, Display area, Display area H, Display area V and
Full screen cannot be adjusted when “RGB”, “1035i
(HDTV)”, “1080i(HDTV)”is selected on PC System Menu
(P24).
3 
						

							28
8. Computer InputPicture Image Adjustment
Picture Image Adjustment
Image Level Select (Menu)
Press Menubutton to display the On-Screen Menu. Press
Cursor Left/Rightbutton to select Image SelectMenu icon.
Press Cursor Downbutton to select the level that you want to
set and then press OK button.
Select the level and
press OKbutton.
The  selected level.
IMAGE SELECT MENU
Normal picture level preset on this projector.Standard
Picture level with improved halftone for graphics.Real
User preset picture adjustment in Image AdjustMenu (P29). Image 1~4
Image Select
Menu icon
Image Level Select (Direct)
Select image level from Standard, Real, Image 1, Image 2, Image
3 and Image 4 by pressing V-effectbutton on the remote control.V-effect button
Standard
Real
Image 1
Image 2
Image 3
Image 4
Normal picture level preset on this projector.  
Picture level with improved halftone for graphics.
User preset image adjustment in Image Adjust Menu (P29). Standard
Real
Image 1~4
2
1 
						

							29
Picture Image Adjustment8. Computer Input
Press Cursor Left/Right
buttons to adjust value.
Reset all adjustment to previous figure.
Reset
Store
Closes the Image Menu.
Quit
Press Menubutton to display the On-Screen Menu.  Press
Cursor Left/Right buttons to selectImage AdjustMenu icon.
Press Cursor Downbutton to select the item that you want to
adjust. and then press OKbutton.  The level of each item is
displayed.  Adjust each level by pressing Cursor Left/Right
button(s).
Select an item and
then press OKbutton.
IMAGE ADJUST MENU
Image Level Adjustment
Press Cursor Left/Rightbutton to adjust the image contrast
(From 0 to 63.)
Press Cursor Left/Rightbutton to adjust the image brightness.
(From 0 to 63.)Contrast
Brightness
Press either Cursor Left or Rightbutton to obtain better balance
of contrast.  (From 0 to 15.)Gamma
To store manually preset image, select Storeicon and press
OK button.  Image LevelMenu will appear. Select one from
Image 1 to 4 where you want to set and then press OK button.
Storeicon
Press OKbutton at this icon to store
the adjustment.Image Adjust
Menu icon
Press Cursor Left/Rightbutton to adjust the red tone.  (From 0 to 63.) White balance (Red)
Press Cursor Left/Rightbutton to adjust the green tone. (From 0 to 63.) White balance (Green)
Press Cursor Left/Rightbutton to adjust the blue tone.  (From 0 to 63.) White balance (Blue)
Selected Image level
Color temp.
Press either Cursor Leftor Rightbutton to select the Color temp.
level. (XLow, Low, Mid or High) 
2
1
3
Image Level Menu
Select one from image 1
to 4 where you want to
set  and then press OK
button. 
						

							30
8. Computer InputPicture Screen Adjustment
Picture Screen Adjustment
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press Menubutton to display the On-Screen Menu.  Press
Cursor Left/Rightbutton(s) to select Screen Menuicon.
When Digital zoom +is selected, the On-Screen Menu
disappears and the message “D-Zoom +” is displayed.  Press OK
button to expand image size.  And press Cursor
Up/Down/Left/Right button(s) to pan the image.  Panning function
can work only when the image is larger than screen size.
A projected image can be also expanded by pressing D-zoom +
button on the remote control.
To cancel Digital Zoom +/– mode, press any button except D-
zoom + / –, OK, Cursorbuttons.
Select the function
and press OKbutton.
Press Cursor Downbutton to select the function and then
pressOK button.
Wide
Digital zoom +
Provides image to fit screen size.Normal
True
SCREEN MENU
Screen Menuicon
When Digital zoom – is selected, the On-Screen Menu disappears
and the message “D-Zoom –” is displayed.  Press OKbutton to
compress the image size. 
A projected image can be also compressed by pressing D-zoom –
button on the remote control unit.  Digital Zoom –
Provides an image in its original size.  When the original image size
is larger than the screen size (1024 x 768), this projector
automatically enters “Digital zoom +” mode. 
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly.  This function can be used for providing a
squeezed video signal at 16 : 9.
Note:
–Picture screen adjustment cannot be operated when
“1035i (HDTV)”, “1080i (HDTV)”is selected on PC
System Menu  (P24).
–Wide cannot be selected when “720p (HDTV)” is
selected on PC System Menu  (P24).
–True and Digital zoom +/– cannot be operated when
“RGB” is selected on PC System Menu  (P24).
–This projector cannot display any resolution higher
than 1280 X 1024.  If your computer’s screen
resolution is higher than 1280 X 1024, reset the
resolution to the lower before connecting the
projector.
–The image data in other than XGA (1024 x 768) is
modified to fit the screen size in initial mode.
–Panning function may not operate properly if the
computer system prepared on PC Adjust Menu is
used.
2
1