Philips Proscreen Pxg20 Projector User Manual

19 Auto Sync Display Function
Normally, an image is not superimposed during Auto Sync
adjustment. You can, however, choose to superimpose a
background image during Auto Sync adjustment.
1.Press Menu.2.Press 1 /2to select ‘Fine sync’3.Press 3 /4to select ‘Auto Sync Disp’.
4.Press 1 /2to select ‘’ to superimpose a background
image or ‘’ to remove the background image during Auto
Sync adjustment.
5.To exit from the GUI, press Menu.
DATA MODE / VIDEO MODE DISPLAY
Picture adjustments
For Data / Video signal...

20
8. OPERATION
Selecting signal type
This function allows you to select the input signal type
(Computer/RGB or Component) for Data in 1 or 2 port.
1.Press Menu.2.Press 1 /2to select ‘Picture’.3.Press 3 /4to select ‘Signal Type’, and then press2.
4.Press 3 /4to select ‘Computer/RGB’ or ‘Component’.5.Press OK to save the setting.6.To exit from the GUI, press Menu.
Interlaced (I)/Progressive (P) conversion
This function allows you to select either an interlaced display
or a progressive display of a video...

21
PERSONAL PREFERENCES
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these settings
are stored, they can be easily selected each time you connect
the computer to the projector.
Saving/changing the adjustment setting
1.Press Menu.2.Press 1 /2to select ‘Fine Sync’.
3.Press 3 /4to select ‘Save Setting’, and then press OK.
4.Press 3 /4to select the desired memory location of the
setting.
5.Press OK to save the setting.
6.To exit from the GUI, press...

9. OTHER SETTINGS
REVERSE/INVERT IMAGE FUNCTION
This projector is equipped with a reverse/invert image function 
which allows you to reverse or invert the projected image for
various applications.
Front Normal image
Ceiling+Front Inverted image
Rear Reversed image
Ceiling+Rear Reversed and inverted image
1.Press Menu.2.Press 1 /2to select ‘PRJ Mode’.
3.Press 3 /4to select the desired projection mode.
4.Press OK to save the setting.5.To exit from the GUI, press Menu.Projection using a mirror
–Place a...

23
DIGITAL IMAGE MAGNIFICATION (D-ZOOM)
This function allows you to magnify a specific portion of an
image. This is useful when you want to display a detailed
portion of the image. 
1.Press D-Zoom. Each time D-Zoom is pressed, the image will
be magnified.
2.When the image is magnified, you can pan and scan around
the image by using 3 ,4 , 1 or2.
–Each time D-Zoom is pressed, image magnification toggles
as shown below.
x1 x2 x3 x4 x6 x8
–If the input signal is changed during digital image
magnification,...

9. OTHER SETTINGS
Picture display mode 
(V-Format) (on projector keyboard only)
24
DATA MODE
4:3 aspect ratio
Other aspect ratios
SVGA (800 x 600)
XGA (1024 x 768)
UXGA (1600 x 1200)
SXGA (1280 x 1024)
NORMAL
1024 x 768
1024 x 768
1024 x 768
960 x 768
FIT TO SCREEN
–
–
–
1024 x 768
DOT BY DOT
800 x 600
1024 x 768
1600 x 1200
1280 x 1024
VIDEO MODE
4:3 aspect ratio, 480I/P,
NTSC, PAL, SECAM
16:9 aspect ratio, 720P,
1080i
4:3
Letterbox
Squeeze
480I/P,720P,1080i
NORMAL
1024 x 768
1024 x 768
–
–
WIDE
1024 x...

25
ON-SCREEN DISPLAY OVERRIDE FUNCTION
This function allows you to turn off the on-screen messages
that appear during ‘input select’. Once ‘OSD Display’ is set to
‘’ in the GUI menu, the on-screen messages will not
appear when Data 1, Data 2 or Video are pressed on the
projector or Input on the remote control.
1.Press Menu.2.Press 1 /2to select ‘Options’.3.Press 3 /4to select ‘OSD Display’.
4.Press 1 /2to select ‘’ to turn on or ‘’ to turn off
the On-Screen Display.
5.To exit from the GUI, press Menu....

26
9. OTHER SETTINGS
4.Enter the new password using 3/ 4to select the desired
number, and then press 2to select the next digit. Continue
this procedure for the remaining three digits, and then press
OK.
5.Enter the password again (‘Reconfirm’) using 1/2/3/4, and
then press OK
6.To exit from the GUI, press Menu.
Note:
After setting the password, be sure to write it down in a secure
location so as not to forget it.
Changing the Password
1.
Follow steps 1 to 3 in ‘Setting the Password’ above.2.Enter the old...

27
1.Press Menu.2.Press 1 /2to select ‘Options’.3.Press 3 /4to select ‘Background’, and then press 2.
4.Press 3 /4to select the background image you want to
display on the screen.
5.Press OK to save the setting.6.To exit from the GUI, press Menu.
SELECTING A STARTUP IMAGE
–This function allows you to specify the image to be
displayed upon the projector’s startup.
Description of Startup ImagesSelected item Background image
Philips PHILIPS default image
None Black screen
1.Press Menu.2.Press 1 /2to select...

10. MENU TREE
28
MAIN MENU
Picture
Fine Sync
Audio
Options
Language
PRJ Mode
StatusContrast
Bright
Color(Compo.input only)Tint(Compo.input only)Sharp(Compo.input only)Red
Blue
CLR Temp
Reset
Signal Type
I/P Conversion
Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp
Vo l u m e
Balance
Treble
Bass
Reset
Lamp Timer
AV mute Disp
OSD Display
Background
Startup Image
MNTR Out/RS232C
Auto Power Off
Key Lock Level
Password
English
Deutsch
Espanol...