Philips Mcd107 User Manual

							22
Select sampling rate
You can select the Linear Pulse Code 
Modulation (LPCM) output sampling rate. The 
higher the sampling rate, the better the sound 
quality.
1Press 6$8,26(783@ (audio setup) > 
>2:16$03/(@ (down sample), then 
press 
.
3Select an option, then press 2..
[ ‡.@: For discs recorded at sampling 
rate of 48kHz.
[ ‡.@: For discs recorded at sampling 
rate of 96 kHz.
[ ‡.@: For discs recorded at 
sampling rate of 192 kHz.
4Press 6 [1,*+702(@ (night mode), then 
press 
.
3Select an option , then press 2..
‡>21@ (on): Enjoy quiet viewing at 
night.
‡>2))@ (off ): Enjoy surround sound 
with its full dynamic range.
4Press 6 
>2:10,;@ (downmix), then press 
.
3Select an option, then press 2..
‡>/757@: Select this if the unit is 
connected to a Dolby Pro Logic 
decoder.
‡>67(5(2@ (stereo): Select this when 
output delivers sound from only the 
two front speakers.
4Press 6 
>352&(66,1*@ (3d processing), then 
press 
.
3Select an option, then press 2..
‡>2))@ (of f ), 
‡>&21&(57@ (concer t) 
‡>&+85&+@ (ch u r ch) 
‡>3$66,9(@ (passive)
‡>:,(@ (wide) 
[ ‡/,9(@ (live)
4Press 6
						

							23
Set the sleep timer
This unit can switch to standby automatically 
after a set period of time.
1When the unit is turned on, press SLEEP
repeatedly to select a set period of time 
(in minutes).
When sleep timer is activated, the  »
display shows 
.
7RGHDFWLYDWHVOHHSWLPHU
1Press SLEEP repeatedly until >2))@ is 
displayed.
When sleep timer is deactivated,  »
disappears on the display.
/LVWHQWRDQH[WHUQDOGHYLFH
You can listen to an external device through 
this unit.
1Press 03/LQN to select the MP3 link 
source. 
Connect the supplied MP3 link cable to:
‡03/LQN jack (3.5 mm) on the unit
the headphone jack on an external  ‡
device.
3Star t to play the device (see the device 
user manual).
 2WKHUIHDWXUHV
Set the alarm timer
This unit can be used as an alarm clock. The 
DISC, USB or TUNER is activated to play at a 
preset time.
1Ensure that you have set the clock 
correctly.
In standby mode, press and hold 7,0(5.
3Press ,6&,781(5 or USB to select a 
source.
4Press 7,0(5WRFRQ
						

							24
)0
Tuning range 87. 5 - 108 MHz
Tuning grid 50 kHz
Sensitivity
 - Mono, 26 dB S/N ratio 82dB/m/W
*HQHUDOLQIRUPDWLRQ
AC power 220 - 230 V, 50 Hz
Operation power 
consumption 20 W
Standby power 
consumption 
						

							25
 7URXEOHVKRRWLQJ
Warning
Never remove the casing of this apparatus. ‡
To keep the warranty valid, never tr y to repair 
the system yourself. 
If you encounter problems when using this 
apparatus, check the following points before 
requesting ser vice. If the problem remains 
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact 
Philips, ensure that the apparatus is nearby 
and the model number and serial number are 
available.
No power
Ensure that the AC power plug of the  ‡
unit is connected properly.
Ensure that there is power at the AC  ‡
outlet.
As a power-saving feature, the unit  ‡
switches off automatically 15 minutes 
af ter track play reaches the end and no 
control is operated.
No sound or poor sound
No sound or poor sound
Adjust the volume. ‡
Disconnect the headphones. ‡
Check that the speakers are connected  ‡
correctly.
Check if the stripped speaker wires are  ‡
clamped.
/HIWDQGULJKWVRXQGRXWSXWVUHYHUVHG
Check the speaker connections and  ‡
location.
86%SOD\DELOLW\LQIRUPDWLRQ
&RPSDWLEOH86%GHYLFHV
86%
						

							26
86%GHYLFHQRWVXSSRUWHG
The USB device is incompatible with the  ‡
unit. Tr y another one.
Poor radio reception
Increase the distance between the unit  ‡
and your T V or VCR .
Fully ex tend the FM antenna. ‡
7LPHUGRHVQRWZRUN
Set the clock correctly. ‡
Switch on the timer. ‡
&ORFNWLPHUVHWWLQJHUDVHG
Power has been interrupted or the power  ‡
cord has been disconnected. 
Reset the clock /timer. ‡ 1RUHVSRQVHIURPWKHDSSDUDWXV
Disconnect and reconnect the AC power  ‡
plug, then turn on the system again.
As a power-saving feature, the system  ‡
switches off automatically 15 minutes 
af ter track play reaches the end and no 
control is operated.
5HPRWHFRQWUROGRHVQRWZRUN
Before you press any function button,  ‡

						

							27

LJLWDO$XGLR
Digital Audio is a sound signal that has been 
conver ted into numerical values. Digital sound 
can be transmitted through multiple channels. 
Analog sound can only be transmitted through 
two channels.
LVFPHQX
A screen display that allows election of images, 
sounds, subtitles, multi-angles, etc., recorded 
on a DVD.
LY;
						

							28
Surround
A system that creates realistic, three-
GLPHQVLRQDOVRXQG