Philips Bcool Xg1 Projector User Manual

For computer signal input, the following ‘Picture’ adjustments can be made.
Picture adjustments
•Press Menu and select ‘Picture’ in the menu bar. The following ‘Picture’ adjustments can now
be made according to the instructions under ‘General explanation’:
– Brightness
adjusts brightness of the displayed picture;
– Contrast
adjusts the overall contrast intensity;
– Sharpness
controls the contour impression of the picture:
– Frequency
changes the display data frequency to match the frequency of your...

Features adjustments
Press Menu and select ‘Features’ in the menu bar. The following ‘Features’ adjustments can now
be made according to the instructions under ‘General explanation’:
– PIP (Picture In Picture)
switches the PIP window on and off. PIP enables projection from a second source in the
currently projected computer or component video picture. The currently projected
computer or component video picture can also be used as input source.
Please note that the second source can only be displayed in...

Setup adjustments
•Press Menu and select Setup in the menu bar. The following Setup adjustments can now be
made according to the instructions under ‘General explanation’:
– Language
selects the required menu language;
– Keystone
corrects picture distor tion of the ver tical keystone type by internal scaling;
– Mirror
mirrors the picture for use of the projector in various positions with respect to the
user(s) and the projection screen;
-- Source
selects the current projection source (Auto, Computer, DVI,...

Switch off and disconnect the projector before cleaning.
1Press the Standby button twiceto switch off the projector.
– The Standby indicator star ts lights up red.
2Wait until the cooling fan has stopped (about 1 minute after the projector has been put in
Standby) and disconnect the mains lead and all other cables.
Cleaning the cabinet
•When the cabinet is dusty, clean it by gently wiping with a soft cloth.
•A chamois leather slightly moistened with water is sufficient for cleaning the housing.
•Do not...

>
When operation time reaches the last 1400 hours of the average lamplife, the message ‘Lamp
life has almost exceeded’ will be displayed on the screen, When operation time reaches 1500
hours, the message ‘Lamp life has exceeded’ will be displayed.
The lamplife remaining can be checked using the OSD menu.
1Press Menu.
2Use Cursor Control to move the cursor to ‘Setup’.
3Use Cursor Control to select ‘Lamp counter’.
1Switch off the projector and wait until the lamp has cooled down before disconnecting the...

>
1Press Menu.
– The menu bar appears on the screen.
2Use cursor control to select ‘Setup’ in the menu bar.
3Use cursor control to select ‘Lamp counter’ in the sub menu.
4Press OK to reset the lamp counter.
5If required, select another item you wish to adjust or press Menu to exit.Resetting the lamplife
time
Philips Multimedia Projector26English User guide bCool XG1
6. Maintenance
Temp.OK
Menu
Source Auto Image
LampTemp.OK
Menu
Source Auto Image
Lamp 

>
If a fault occurs, first check the points listed below before taking the projector for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or ser vice
organisation.
Under no circumstances should you tr y to repair the projector yourself as this could invalidate the
guarantee.
– Possible cause
•Solution
General
– Mains lead is not correctly connected.
•Correctly connect mains lead.
– Lamp holder cover is not closed correctly or the lamp holder is damaged.
•Close...

>
•Adjust ‘Brightness’, ‘Contrast or ‘Colour tracking’ (see ’Picture adjustment’ under ‘Operation’ -
‘On Screen Display Menu’).
•Reset all projector settings in the ‘Setup’ menu (‘Factor y settings’).
– Image is not focused.
•Adjust focus ring.
– Distance between projector and screen is not correct.
•Adjust the distance between the projector and the screen.
– Signal cable is not correctly connected.
•Connect signal cable correctly.
– Signal cable is not correctly connected.
•Connect signal cable...

– ’Childlock’ active.
•Switch off ‘Childlock’ in the ‘Features’ menu.
•Check that the batteries are installed properly in the remote control and/or replace the
batteries.
•Check that the projector receives the signals from the remote control.
•Check that the USB cable has been properly connected.
•Check that both projector and computer are switched on.
•Unplug the USB cable and then reconnect.
•Connect another USB device (mouse, scanner, webcam, etc.) and see if it works.
If it does not work there is a...