Philips 47pfl7403d User Manual
Have a look at the manual Philips 47pfl7403d User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 619 Philips manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENGLISH FRANÇAISE ESPAÑOL EN-9 3.6 Switch on and setup the TV The TV switches on automatically after connecting the power cord. Press the GREEN Next button located on your remote control to proceed. Thank you for your purchase of this PHILIPS TV. Please proceed with the following steps to set-up your TV . Fo r the BESTpossible picture performanc e, contact your local Cable / Satellite signal pr ovider for High Definition signal options available in yo ur area. Next Follow the on-screen instructions to select your language and complete your TV setup. Installation takes approximately 10 minutes. Note: D If you connect your TV to a cable box or satellite set-top box, you do not need to install channels. Press the red button on the remote control to exit the channel installation stage of the setup. Finish the setup by selecting your location: If you choose • Retail store your settings will be are erased each time you turn off the TV. This mode is only to be used for retail store displays. If you choose • Home you are guided through a choice of picture display options. Use the left and right cursor to select your preferred screen.
EN-10 ENGLISH FRANÇAISE ESPAÑOL Use your TV 4. This section helps you perform basic TV operations. Switch your TV on/off or to standby 4.1 To switch the TV on Press • . POWER at the right side of the TV. POWER To switch to standby Press • . on the remote control. To switch on from standby without the remote control Press • . POWER at the right side of the TV to switch the TV off. Press • . POWER again to switch the TV on. To switch off Press • . POWER at the right side of the TV. Note D Energy consumption contributes to air and water pollution. When the power cord is plugged in, your TV consumes energy. Your TV has a very low standby power consumption. Watch TV 4.2 Switch channels Press a number (1 to 999) or press 1. CH+ or CH- on your remote control. For digital channels, press a number (1 to 999) followed by a dot "." and then the corresponding sub channel number (1 to 999). Ex. 108.30. Press 2. PREV CH to return to the previously viewed TV channel. Note D You can also switch channels by pressing CHANNEL - or + on the side controls of the TV. Adjust volume Press 1. VOL+ or VOL- on your remote control. Press 2. MUTE on your remote control to mute the sound. Press MUTE again or press VOLUME - or + to restore the sound. Note: D You can also adjust the volume by pressing VOLUME - or + on the side controls of the TV. To increase the headphone volume, press the volume button on the TV or remote control. When headphones are plugged into the TV, the loud speakers are automatically muted.
ENGLISH FRANÇAISE ESPAÑOL EN-11 Watch channels from a set-top box 4.3 Switch on the set-top box. 1. The picture from your set-top box might appear automatically on your screen. Use the remote control of your set-top box to select channels. 2. If the picture does not appear Press 1. SOURCE repeatedly to select the connected set-top box and wait a few seconds for the picture to appear. Use the remote control of your set-top box to select channels. 2. 4.4 Watch connected devices Switch the connected device on. 1. The picture from your connected device might appear automatically on the TV. If the picture does not appear Press 1. SOURCE repeatedly to select the connected device and wait a few seconds for the picture to appear. Watch a DVD 4.5 Insert a DVD disc in your player. 1. Press 2. Play Æ on the remote control of your player. The picture from the player might appear automatically on your screen. If the picture does not appear Press 1. SOURCE repeatedly to select the DVD player and wait a few seconds for the picture to appear.
EN-12 ENGLISH FRANÇAISE ESPAÑOL 5. Use more of your TV This section describes the advanced features of your TV. 5.1 Understand the remote control 21 4 2 3 9 15 6 12 13 16 18 14 1 11 19 8 7 17 10 20 5 . 1. Switches the TV on from standby or back to standby. The TV is never powered off completely unless it is physically unplugged. SOURCE 2. Selects connected devices. FAV 3. To display a list of all channels marked as favorite (including subchannels). FORMAT 4. Selects a picture format. See Change picture format on page 14. Color keys 5. Selects tasks. OPTION 6. Activates the quick access menu. For information, see Use the quick access menu on the next page . OK 7. To display the channel list or to activate a setting. Cursor buttons 8. Í Æ Î ï To navigate through the menus. INFO 9. Press to display information about the selected TV channel and program or accessory device. The quality and accuracy of the information on the information banner are transmitted from broadcasters. You may see a difference in broadcast time if the broadcaster is from a different time zone area. + CH - 10. Channel up/down Switches to the next or previous channel. MUTE 11. Mutes or restores sound. Number keys 0-9 12. Selects a channel, page or setting. ( . ) 13. Press the dot (.) for digital channels. PREV CH 14. Returns to the previously-viewed channel. +VOL- 15. Volume up/down Increases or decreases volume. MENU / EXIT 16. Toggles the menu on or off. BACK 17. To return to the previous menu. AUTO MODE 18. Toggles between preset picture and sound settings. For information, see Use Auto Mode on page 16. DEMO 19. Toggles the demo menu on or off. For information, see Use the demo mode on page 25. SLEEP 20. To set a delay after which the TV switches to standby. For information, see Set the sleeptimer on page 17. Active Control 21. The TV continuously measures and corrects incoming signals to provide the best picture possible.
ENGLISH FRANÇAISE ESPAÑOL EN-13 5.2 Use the quick access menu The quick access menu gives direct access to some often needed menu items. Note D When digital channels are installed and broadcast, the relevant digital options are displayed in the quick access menu. Press 1. OPTION on the remote control. Press 2. Î or ï and then OK to access one of the following menus: Audio language • For digital channels only, where multiple audio languages are broadcast. Closed captions • See View closed captions (subtitles) on page 21. Picture format • See Change picture format on the next page . Equalizer • See Change sound settings on page 15. Clock • See Set the clock on page 17. 5.3 Change picture and sound settings Change picture settings This section describes how to adjust your picture settings. Press 1. MENU on the remote control. Press 2. Æ to enter the TV settings menu. TV settings Settings assistant Pi cture Sound TV menu TV settings Fe atures Installation Press 3. ï and Æ to select the Picture menu. Picture Contrast Brightness Color Tint Sharpness Color temperature Dynamic contrast HD Natural Motion* TV Settings TV menu Settings assistant Picture Sound *Available in selected models Press 4. Î or ï to select one of the picture settings, and press Æ to enter the setting. Press 5. Î or ï to adjust the setting, and press Í or OK to confirm the change. Press 6. Menu to exit. Change picture settings by using the setting assistant This section guides you through a picture settings wizard. Press 1. MENU on the remote control. Press 2. Æ to enter the Settings assistant menu. Settings assistant Start now TV menu Installation TV settings Settings assistant Pi cture Sound Press 3. Æ to highlight Start now, and press OK to start the Settings assistant. You are guided through a choice of picture display options. Press the color keys, cursor keys and OK to make your selections and store your setup.
EN-14 ENGLISH FRANÇAISE ESPAÑOL Summary of picture settings The following picture settings can be configured. Depending on the format of the picture source, some picture settings might not be available. • Contrast - Sets the level of white in the picture. • Brightness - Sets the brightness of the picture. • Color - Sets the level of saturation. • Tint - Adjusts the color balance between red and green. • Sharpness - Sets the sharpness of fine details. • Color temperature - Sets the color temperature to normal, warm or cool. • Dynamic contrast - Enhances contrast in the darker and the brighter picture areas as the image on the screen changes. HD Natural Motion (HDNM) • - In selected TV models only. Reduces field and line flicker to display movement smoothly. You can switch HDNM on or off. • Digital Noise Reduction (DNR) - Automatically filters out and reduces image noise and improves picture quality when receiving weak video signals. You can switch DNR on or off. • MPEG artifact reduction - Smooths transitions on digital pictures. You can switch MPEG artefact reduction on of off. • Color enhancement - Makes colors more vivid and improves the resolution of details in bright colors. You can switch color enhancement on or off. • Active control - Corrects incoming signals to provide the best picture possible according to lighting conditions in the room. You can switch Active Control to one of these settings: Off, On with light sensor or On without light sensor. Picture format • - Changes the format of the picture. • Horizontal shift - Adjusts the horizontal position of the picture. • Vertical shift - Adjusts the vertical position of the picture. Change picture format Press 1. FORMAT on the remote control. Press 2. Î or ï to select a picture format and press OK to confirm your choice. Summary of picture formats The following picture formats can be selected. Depending on the format of the picture source, some picture formats might not be available. Automatic (Not for PC mode.) Enlarges the picture automatically to best fit the screen. The subtitles remain visible. Super zoom (Not for HD and PC mode.) Removes the black bars on the side of 4:3 broadcasts. There is minimal distortion. 4:3 Shows the classic 4:3 format. Movie expand 14:9 (Not for HD and PC mode.) Scales classic 4:3 format to 14:9. Movie expand 16:9 (Not for HD and PC mode.) Scales the classic 4:3 format to 16:9. Wide screen Stretches the classic 4:3 format to 16:9 Unscaled (In selected TV models only) (For HD and PC mode only) Allows maximum sharpness. Some distortion may be present due to the broadcaster's systems. Set your PC resolution to widescreen mode for best results.
ENGLISH FRANÇAISE ESPAÑOL EN-15 Change sound settings This section describes how to adjust your sound settings. Press 1. MENU on the remote control and select TV settings > Sound. Sound Equalizer Balance Digital audio language Alternate audio Mono/Stereo Incredible surround AVL BBE TV Settings TV menu Settings assistant Picture Sound Press 2. Î or ï to highlight a sound setting and press Æ to select the setting. Press 3. Î or ï to adjust the setting, and press OK to confirm the change. Press 4. Menu to exit. Summary of sound settings The following sound settings can be configured. Depending on the sound source, some sound settings might not be available. • Equalizer Changes the bass and treble. Select a bar to change the setting. Balance • Sets the balance of the left and right speakers. • Digital audio language Available for digital channels only, when multiple languages are broadcast. Lists available audio languages. • Alternate audio Available for analog channels only when a main and second audio program (SAP) is available from the broadcaster. Select the main or second audio program. Mono/Stereo • Select mono or stereo. Incredible surround • Sets modes for spatial or surround sound reproduction depending on the broadcast signal or on signals from external input. Select on or off. • Automatic volume leveling (AVL) Reduces sudden volume changes, for example, during commercials or when switching from one channel to another. Select on or off. • BBE Restore clarity for better speech intelligibility and musical realism. Select on or off. • Delta volume Levels out volume differences between channels or connected devices. Switch to the connected device as described in Watch connected devices on page 11 before changing the Delta volume.
EN-16 ENGLISH FRANÇAISE ESPAÑOL 5.5 Create and use lists of favorite channels This section describes how to create and use lists of your favorite channels. Select a list of favorite channels Press the 1. FAV key on the remote control. Your lists of favorite channels are displayed. Press 2. Î or ï to highlight a list, and press OK to select the list. Create or edit a list of favorite channels Press the 1. FAV key on the remote control to display your lists of favorite channels. Press 2. Î or ï to highlight a list, and press OK to select the list. Press the green key to enter 3. Edit mode. A list of channels is shown. Press 4. Î or ï to highlight a channel. Press 5. OK to select or deselect the highlighted channel. The channel is added to or removed from the list of favorite channels. Press the green key to exit. 6. Switch to one of the channels on a list Press the 1. OK key on the remote control to display the last list that you selected. Press 2. Î or ï to highlight a channel. Press 3. OK select the channel. The TV switches to that channel. 5.4 Use Auto Mode Press 1. Auto Mode to set your TV to a predefined picture and sound setting. Press 2. Î or ï to select one of the following settings: Personal • The customized settings you defined by using the Picture menu. Sports • Vivid picture settings and clear sound for high action. Standard • For normal TV viewing. Movie • Brilliant picture settings for a cinematic experience. Game • Optimized for PCs, games consoles and playstations. Power saver • Eco friendly settings for lower power consumption.
ENGLISH FRANÇAISE ESPAÑOL EN-17 5.6 Set the clock This section describes how set the time, date, time zone, and daylight saving. Set the time automatically Some digital channels transmit the time. For these channels, you can set the time automatically. Follow these steps to set the time automatically and to choose which channel to read the time from. Press1. MENU on the remote control and select Installation > Clock > Auto clock mode. Select 2. Automatic, and press Í to confirm your choice. Auto clock mode Manual Au tomatic Clock TV menu I Installation Au to clock mode Au to clock channel Time zone Daylight saving (Optional) Select the channel from which the TV will read the time. 3. Press • ï and Æ to enter the menu for Auto clock channel. Press • Î or ï to highlight a channel. Press • Í to confirm your choice. (Optional) Select the time zone. 4. Press • ï and Æ to enter the menu for Time zone. Press • Î or ï to highlight the time zone. Press • Í to confirm your choice. (Optional) Set daylight saving. 5. Press • ï and Æ to enter the menu for Daylight saving. Press • Î or ï to highlight Automatic or Off. Press • Í to confirm your choice. Press 6. MENU to exit. Set the time manually Press1. MENU on the remote control and select Installation > Clock > Auto clock mode. Press 2. Î or ï to select Manual, and press Í to confirm your choice. Au to clock mode Manual Automatic Clock TV menu I InstallationAu to clock mode Time Day Press 3. ï to select Time and then press Æ to set the time. Use the format HH:MM. Select AM/PM for morning or afternoon. Press 4. OK to confirm your choice. Press 5. ï and Æ to enter the menu for Day. Press 6. Î or ï to select the day. Press 7. OK to confirm your choice. Press 8. MENU to exit. Set the sleeptimer 5.7 This section describes how to program the TV to switch off automatically after a delay. Press 1. MENU on the remote control and select Features > Sleeptimer . SleeptimerFeatures TV menu Caption settings Sleeptimer Child lock Change PIN Demo 90 min Press 2. Î or ï to select a value from 0 to 180 minutes. For example, when you select 90, the TV switches to standby in 90 minutes. Press 3. MENU to exit. Tip E To turn the sleeptimer off, select 0 minutes.
EN-18 ENGLISH FRANÇAISE ESPAÑOL Use child control and rating locks 5.8 This section describes how to lock or unlock the TV. You can set a personal identification number (PIN) and prevent your children from watching certain programs or certain channels. Set or change your PIN Press1. MENU on the remote control and select Features > Change PIN. Enter a 4-digit PIN with the number keys on the remote control. 2. If you have a PIN, enter your current PIN. • If you do not have a PIN or if you have lost your PIN, enter • 0711 . Enter your new 4-digit PIN and then enter it again to confirm. 3. A message appears to confirm that your PIN has been changed. Press 4. MENU to exit. Lock the TV This section describes how to lock all channels on the TV. At the specified time, screen is blanked out and the audio is muted. Ensure that the clock is set with the current time. For information 1. about how to set the clock, see Set the clock on the previous page. Press2. MENU on the remote control and select Features > Child lock > Lock after. Enter your PIN. 3. If you do not have a PIN, set one as described in Set or change your PIN on this page. Press4. Æ to select Timer. Lock after Timer Time TV menu Features Of On Child lock Timer Press 5. ï to select On and activate the Lock after feature. Selecting Off deactivates the feature. Press 6. Í to confirm your choice. Press 7. ï to select Time and then press Æ to set the time. Use the format HH:MM. Select AM/PM for morning or afternoon. Press8. OK to confirm the time. Press 9. MENU to exit. Please restart your TV to activate this function. 10. Lock a channel This section describes how to lock specified channels. The channels can be selected but the screen is blanked out and the audio is muted. Press1. MENU on the remote control and select Features > Child lock > Channel lock. Enter your PIN. 2. If you do not have a PIN, set one as described in Set or change your PIN on this page. Channel lock Channel 1 Sport Child Lock TV menu Features Lock af ter Channel lock TV ratings lock Mo vie ratings lock Canada English ratings lock Canada French ratings lock Region ratings lock Channel 2 News Channel 3 Movies Channel 4 Channel 5 Channel 6 Channel 7 Press 3. Î or ï and then press OK to lock one or more channels or external sources. Each channel has a box-graphic in front of it to indicate whether it is locked: A box with • X indicates that the channel is locked An empty box indicates that the channel is not locked • Press 4. MENU to exit.